Highly Components HC-61 Manual de usuario
HC-61
Installation Manual
Welcome to use HC-61 Infrared LED Sensor Lamp!
The product is an energy-saving automatic sensor lamp, adopting integrated circuit and precise
detecting components. It gathers automatism, convenience, safety, saving-energy and practical
functions. Its performance is stable. It can identify day and night. The lamp can turn on when one
enters detection field and can turn off automatically when one leaves detection field.
SPECIFICATION:
Power Source: 220-240V/AC Detection Range: 240°
Power Frequency: 50/60Hz Detection Distance: 5-10m(<24℃)adjustable
Ambient Light: <3-2000LUX (adjustable) Working Temperature: -20~+40℃
Time Delay: Min.10sec±3sec Working Humidity: <93%RH
Max.15min±2min Installation Height: 1.8-2.5m
Rated Load: 30W (2200LM) Detection Moving Speed: 0.6-1.5m/s
Additional switching capacity: 500W IP Class: IP65
FUNCTION:
Can identify day and night: The consumer can adjust working state in different ambient light.
It can work in the daytime and at night when it is adjusted on the “sun” position (max). It can
work in the ambient light less than 3LUX when it is adjusted on the “3” position (min). As for
the adjustment pattern, please refer to the testing pattern.
SENS adjustable: It can be adjusted according to using location. The detection distance of
low sensitivity could be only 5m and high sensitivity could be 10m which fits for large room.
Time-Delay is added continually: When it receives the second induction signals within the
first induction, it will restart to time from the moment.
Adjustable Time Delay: the length of time delay could be set according to the customers’
requirement, the minimum time of this item is 10sec ± 3sec, the maximum is 15min±2min.
Good sensitivity Poor sensitivity
INSTALLATION:
Switch off the power.
Screw off the nail on the bottom of sensor lamp and
unload the bottom. Open the wire hole in the
bottom and pass the wire through the hole.
Fix the bottom on the selected position with the inflated screw.
Connect the power wire into connection-wire column according to the connection-wire
diagram.
Fix back the sensor lamp on the bottom. Switch on the power and then you can test it.
It not only can install on the wall directly but also can install in the outer corner with the
help of the widget (refer to photograph below):
Flat mounted Outer corner mounted
The LED can tilt up/down, turn left/right according to
the customers’requirement as the right drawing:
CONNECTION-WIRE DIAGRAM:
Another way as follows if connecting with electric fan or other lamp:
SENSOR INFORMATION:
TEST:
Turn the SENS knob clockwise on
the maximum (+). Turn the TIME
knob anti-clockwise on the
minimum (10s). Turn the LUX
knob clockwise on the maximum
(sun).
Switch on the power; the lamp will
have no signal at the beginning. After Warm-up 30sec, the lamp can start work. If it receives
the induction signal, the lamp will turn on. While there is no another induction signal any
more, the lamp should stop working within 10sec±3sec.
Turn LUX knob anti-clockwise on the minimum (3). If the ambient light is more than 3LUX,
the lamp should not work. If you cover the detection window with the opaque objects (towel
etc), the lamp would work. Under no induction signal condition, the lamp should stop
working within 10sec±3sec.
Note: when testing in daylight, please turn LUX knob to (SUN) position, otherwise the
sensor lamp could not work!
NOTE:
Should be installed by electrician or experienced person;
Avoid installing it on the uneven object;
There should be no hindrance and moving objects in front of the detection windows to affect
detection;
Avoid installing it near air temperature alteration zones such as air condition, central heating,
etc;
Considering your safety, please do not open the cover when you find the hitch after
installation;
If there is difference between instruction and the function the product has, please give
priority to product and sorry not to inform you additionally.
SOME PROBLEM AND SOLVED WAY:
The load does not work:
a. Please check if the connection of power source and load is correct.
b. Please check if the load is good.
c. Please check if the settings of working light correspond to ambient light.
The sensitivity is poor:
a. Please check if there is any hindrance in front of the detector to affect it to receive
the signals.
b. Please check if the ambient temperature is too high.
c. Please check if the induction signal source is in the detection field.
d. Please check if the installation height corresponds to the height required in the
instruction.
e. Please check if the moving orientation is correct.
The sensor can not shut off the load automatically:
a. Please check if there is continual signal in the detection field.
b. Please check if the time delay is set to the maximum position.
c. Please check if the power corresponds to the instruction.
Height of installation: 1.8-2.5m
Detection Distance: Max.10m
Otros manuales de Luz exterior de Highly Components
Manuales populares de Luz exterior de otras marcas
Lindby
Lindby 9949029 Manual de usuario
HEPER
HEPER DOGO Side LW6048.585-US Instrucciones de instalación y funcionamiento
HEPER
HEPER LW8034.003-US Instrucciones de instalación y funcionamiento
Maretti
Maretti VIBE S 14.6080.04.A Manual de usuario
BEGA
BEGA 84 253 Manual
HEPER
HEPER MINIMO Instrucciones de instalación y funcionamiento
LIGMAN
LIGMAN BAMBOO 3 Manual de usuario
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Manual de usuario
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Manual de usuario
urban ambiance
urban ambiance UQL1273 Manual de usuario
TotalPond
TotalPond 52238 Manual de usuario
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Manual de usuario