3
Fly high with Hitec
zGvaGyGlGOGP
The KIT version of the Sky Scout only includes the airframe, associated hardware, along with the prop and spinner assembly. The following additional
parts and eTuipment are needed to complete the assembly. 9isit a Radio Control Hobby shop or consult an experienced Àier about purchasing the right
equipment for your needs.
&KDQQHO$LUFUDIW5DGLR
The Sky Scout requires at least a -channel radio to Ày. Adding the
optional ailerons requires a 4th channel, though a 5 or higher channel
radio with mixing features will allow for additional Àight performance.
We recommend Hitec models such as the Optic 5 or Optic 6 Sport for
optimal operational performance
5HFHLYHU
We recommend at least a 5 channel aircraft receiver that matches your
radio system for maximum Àexibility. Models such as the Hitec Minima
6T or 6S will ¿t this need if you are using a Hitec brand .4 *H]Radio.
6HUYRV
You will need at least two Sub Micro servos to complete your model. If
you choose to add the optional ailerons you will need an additional two
sub-micro servos. Hitec recommends using the HS-55 or HS-555M*
on all surfaces. These servos are available at most Radio Control
Hobby stores.
0RWRU
You will need a brushless outrunner motor designed for aircraft use.
We recommend the minimum of a -watt 11Kv motor. The motor
dimensions need to be no more than mm in diameter and mm in
length. To avoid having to use a special adapter make sure the output
shaft is either or .mm in diameter. The Sky Scout Kit contains Prop
adapters in both of these si]es.
(6&
You will also need an Electronic Speed Control with built in BEC that is
suitable for the motor you purchased. Hitec recommends using an ESC
with a minimum rating of an 1A and a BEC output of at least 1.5 amps
%DWWHU\&KDUJHU
For optimal performance Hitec recommends a 3-cell 11.1V 1300mAh
LiPo battery with at least a 15C discharge rating. You will also need a
charger capable of charging this battery as well. tions you are using.
3-4 CH AIR TX
1
RECEIVER
2
SERVOS
3
zGvaGvGzGzG}G
Radio, Receiver and Power Set Components for Each Version
(READY TO GO) stock# 13207
This version includes everything you need to Ày your Sky Scout after a few easy assembly steps.
Semi-assembled model
Semi-assembled model
Hitec Lite 4 .4*H]4-channel Radio w/4AA aIkaline batteries
Hitec Minima 6S Receiver installed
Hitec HS-55 Servos installed
(HITEC TO GO) stock# 13209
This version allows you to Ày your Sky Scout with the Hitec radio you already have or may wish to purchase. Any of Hitec’s
AFHSS .4*H]radios, or radios using a Spectra .4*H]module, can be linked with the Minima 6S included in the H*O set.
Semi-assembled model
Hitec Minima 6S Receiver installed
Hitec HS-55 Servos installed
C1-1100 Brushless Outrunner Motor installed
(PLUG-IN TO GO) stock# 13210
This Sky Scout version is for modelers who already own the additional products needed for Àying. A transmitter, receiver,
charger and suitable batteries are required needed to Ày the model plane.
Semi-assembled model
Hitec HS-55 Servos installed
C1-1100 Brushless Outrunner Motor installed
Hitec HBE-1A ESC installed
C1-1100 Brushless Outrunner Motor installed
Hitec HBE-1A ESC installed
HLP-3S 1300mah Li-Po battery included
C*-115 DC Balancing Charger included
Hitec HBE-1A ESC installed
HLP-3S 1300mah Li-Po battery included
C*-115 DC Balancing Charger included
CHARGER
6
BATTERY &
ESC
5
MOTOR
4
