Herma LP Morgan POP Manual de usuario

LP morgan

user manual

www.lpmorgan.com.au

POP Screen

Important information

Unpacking 3

Installation

Installation - Top Grip Kit 4

Installation - Side Grip Kit 5

Installation - Stabilising Bars 6

Installation - Framed Screens 7

Appendix

Maintenance & Troubleshooting 10

Warranty Information 11

Notes and Cautions

WARNING: A notice indicates potential damage to ceiling and tells you how to avoid the problem.

DANGER: A caution indicates a potential for property damage, personal injury or death.

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without permission of Herma Technologies is strictly forbidden.

Trademarks used in this text: Herma, the Herma Logo, LP Morgan and LP Morgan logo are registered

trademarks of Herma Technologies.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the

marks and names or their product. Herma Technologies disclaims interest in trademarks and trade names

other than its own.

Apr 2006 Version 4.1

Table of contents

To the owner

Congratulations on purchasing an LP Morgan Pop Screen. A high quality,

rigid and low cost rear projection screen, designed for visual merchandising

applications. Please take a moment to review this manual, it will ensure

you many years of trouble-free service from your new POP Screen vertical

mounting kit.

TIP: A tip indicates important information that helps you make better use of your screen.

Important

information

Unpacking the Pop Screen

Supplied

2 x 2m Cable with top

grip suspension kit

2 x 2m Cable with side

grip suspension kit

Stabilising bar kit (for 45’’, 49”, 60” & 69” size screens only):

2 x Stabilising Bars 10 x Screen Grips

4 x End Caps

2 x Sliding mounts

Depending on the size of the screen chosen and the conﬁguration

you have chosen to mount your screen, you should have a selection

of the components shown below:

Frame Kits (NB: frame is pre-assembled if size is either 77” or 84”)

4 x Pieces of frame

extrusion

4 x corner

bracket plate

4 x corner

bracket

8 x M6 grub

screws

misc:

1 x POP screen

cut to size

2 x slide nuts

2 x frame tabsM6 x 12 bolts

2 x M4x12

Grub Screws

installation instructions | 3

4 | installation instructions

Mechanical

Installation

Installation: Top Grip Kit

1. Position universal grips to POP Screen

(See fig 1. and Detail-A)

2. A-1 to secure wire; then A-2 to secure screen.

3. Screw top boss to ceiling

(See Fig 2, Detail-B) Determine desired screen

height, trim wire to length.

(Default wire length = 2000mm).

4. Secure wire at the top with grub screw B-1

Detail B

Detail A

A-2

A-1

B-1

Fig 1: Top Grip Assembly

universal

grip

Fig 2:

Top Grip Hanging

Kit detail Assembly

Top

Boss

to ceiling

installation instructions | 5

Mechanical

Installation

Installation: Side Grip Kit

1. Attach universal grip to POP Screen (See Fig 4a,

step 1) using 2mm allen key (supplied) to tighten M4

grub screw.

2. Screw bosses to ceiling (or wall) - See Fig 5 at the

appropriate spacing (depending on the size of the

screen.

3. Determine desired cable length and trim

appropriately.

4. Screw bottom boss to floor (or wall) (See Detail B)

5. Attach side grips to cable (see Fig. 4a step 2) and

secure screen at the desired height.

Detail A

Detail B

Fig 4: Side Grip Assembly

Fig 5: Side Grip Hanging

Kit Assembly detail

(Detail B)

Fig. 4a:

(Detail A)

1. Secure

to screen

2. Secure

wire

boss

6 | installation instructions

Mechanical

Installation

Installation: Stabilising Bars

1. Remove plastic caps on both ends of top and bottom stabilising bars and

remove clear plastic slide out screen grips (see fig. 6a)

2. Attach plastic grips to top and bottom edges of POP Screen. Make sure

they are securely fastened. Slide in plastic slider into top stabilising bar.

3. Slide in screen with screen grip attached into channel of top and bottom

stabilising bars. Replace

4. Secure Top Bosses (See fig 2 - Detail B) to ceiling at the appropriate

spacing (this depends on the size of the screen).

5. Determine desired cable length and trim appropriately.

6. Secure universal grip to top stablising bar (see fig. 6b).

Mounting Surface

Fig 6a: Stabilising Bar Assembly Detail

Fig 7: Assembled POP Screen with Stabilising Bars

Remove plastic caps

Slide out screen grips

plastic slider

Fig 6b: Universal grip

attachment detail

Tighten

installation instructions | 7

Mechanical

Installation

Position &

align frame

sections

Installation: Framed Screens

Frame Assembly:

• Note: If your screen has been pre-assembled, proceed to page 9.

Fig. 8:

Frame Assembly detail

1. Place two slide nuts into channel of frame section which is intended to

be directly above top edge of image.

2. With frame pieces overturned, place corner bracket on corner bracket

plate and slide both into channel as far as possible as shown in ﬁg. 8.

3. Tighten M6 grub screw using a ﬂathead screwdriver.

4. Repeat for three other corners placing brackets and frame pieces in

position as shown in ﬁg. 9

5. Position and align frame sections, tighten remaining grub screws to

secure the frame.

Corner bracket

plate

Fig. 9: Bracket ﬁxturing for frame assembly.

Place slide nuts

into this channel.

Tighten

8 | installation instructions

Mechanical

Installation

Installation: Framed Screens

1. Place the frame face up on a flat and stable

surface.

2. Open the frame covers (located along the inner

edge of the frame). To do this, reach inside of inner

edge of frame and pull frame covers toward outer

edge of frame.

3. Repeat for three other edges.

4. Place screen into the frame so that it is securely

housed into the base of the frame.

5. Close all four opened frame covers over the frame.

Open Frame

cover

Place screen

into the frame

Fig 10: Securing the screen into the frame

Screen Assembly:

installation instructions | 9

Mechanical

Installation

Installation: Framed Screens

Hanging Attachments and Conﬁguration:

Mounting Surface

Fig 12 : Suspended Frame with Top Grip Suspension Kit

See Fig 2 for Hanging

kit installation

1. Determining appropriate spacing between hanging cables, secure

top grip kits to ceiling. See page 4 of this instruction manual on details

of how to do this.

2. Secure frame tabs to frame with M6 bolt passing through larger hole

of frame tab to slide nut inside of frame channel.

3. Your framed POP screen should appear as that depicted in ﬁg 12.

To slide nut

secure frame tab

with grub screw.

Universal

Grip

M6x12

Bolt

Frame tab

Fig 11: Hanging detail for framed screens.

10 | installation instructions

Maintenance &

Troubleshotting

Maintenance and troubleshooting

Cleaning instructions:

The screen surface on your Pop Screen is extremely delicate. Special attention

to these instructions should be followed when cleaning.

1. A draftsman’s style brush may be used to lightly whisk away any loose dirt or

dust particles. Do not use a sharp instrument to remove any particles. Softly

brush from the centre to the edges.

2. The screen may be cleaned with a mild solution of detergent and water and

a sponge or soft lint free cloth. Rub lightly to remove any stubborn marks, then

blot with a damp sponge to absorb excess water. Use a clean sponge with

clear water to wash off the detergent residue. Dry the screen with a soft cloth/

towel so that the detergent does not have time to dry on the screen.

3. NEVER attempt to use solvents, chemicals or abrasive cleaners on the

screen.

4. We encourage you to keep your screen clean. Avoid getting any foreign

materials on it, as cleaning may prove to be very difficult or even impossible

(scratches, paint, ink, etc.). Never paint in the vicinity of the screen unless the

screen surface is completely protected.

With reasonable care you may expect years of trouble free use of your LP

Morgan POP screen.

Tabla de contenidos

Otros manuales de Pantalla de proyección de Herma

Herma

Herma 2C504 Manual de usuario

Manuales populares de Pantalla de proyección de otras marcas

FART PRODUKT

FART PRODUKT Standard SCREEN Manual de usuario

Draper

Draper E Series Manual

Elite Screens

Elite Screens Elite Tripod Series Manual de usuario

Laarhoven

Laarhoven Companion II Manual de usuario

Renogy

Renogy RMS-LFPS-US Manual de usuario

Da-Lite

Da-Lite ExecutiveElectrol Manual de usuario

Samsung

Samsung S*H65* Manual de usuario

FONESTAR

FONESTAR PPTR-43100-FA Manual de usuario

Slide Clear

Slide Clear Varro XL Manual de usuario

Elite Screens

Elite Screens M85XWS1-SRM Manual de usuario

OS РХ-090Н Manual de usuario

Niko

Niko 10-845 Manual de usuario

Speaka Professional

Speaka Professional 2357532 Manual de funcionamiento

Sima

Sima XL-72 Manual de usuario

Jasic

Jasic EVO 2.0 ET-200P Manual de usuario

Elite Screens

Elite Screens Starling 2 Series Manual de usuario

InFocus

InFocus SC-WALL GRY-92H Manual

Barco

Barco OverView MVL-615 Manual de usuario