Henny Penny 301 Manual de usuario

Thecontrols havefour programming levels,afirst level mode,a

secondlevel mode,athird level mode,andaspecialprogram

mode. In eachlevel,pressingthe setswitch advancesthrough

the programmableitems. Programmodecanbeenteredat

anytimeexceptduring analarm. The left displaydescribesthe

item beingprogrammed. Theright display showsthe item set-

ting andcanbechangedby pressingtheright Up andDown

Switches.

The Low Level ProgramMode allows theoperatorto program

the “global“ setpoint temperature(if enabled),cookandhold

time, andsetupto four alarmsfor the selectedproduct.

1. Pressandhold SetandTemperatureSwitch for atleast

five seconds.A tonewill sound,andthe left displayshows

“OF”andtheright displayshowsthesetpoint temperature.

ThetemperatureLED andall product indicator LED’s flash.

2. Presstheright Up andDown Switchesto program

desiredsetpoint temperaturefor all products.

3. Pressthe setswitch andleft display shows“Slct” and

theright displayshows“Prod”. TheproductLED also

flashes.

4. Presseitherthe left or right Up andDown Switchesto select

aproductto program,andthe LED will belit next,to the

desiredproduct.

5. Pressthe setswitch andthetime LED flashes. The left

displaysshows“Fry” andthe right displayshowsthecook

time. Pressingtheright Up andDown Switchesadjuststhe

cooktime.

6. Pressthe setswitch andthetime LED continuesto flash.

The left display shows“Hold,” theright display showsthe

hold time andcanbeadjustedwith theright Up andDown

Switches.

7. Pressthe setswitch andthe alarmLED flashes. The left

display shows“AL 1”)the right display showsthe alarm

time andcanbeadjustedwith the right Up andDown

Switches.

8. Repeatstep8for alarms2,3, and4.

9. Pressandhold the SetSwitch to exit program mode,or

continueto secondlevelmode.

The SecondLevel ProgramMode allowsthe operatorto pro-

gramloadcompensation,loadanticipation, proportional control,

filter cycle for the selectedproduct,andthe idle parameters.

1. While in the first level mode,pushandhold the Setand

Exit Melt Switchesfor five seconds.The beeperwill sound

the left display will show“Slct” (Select)andthe right display

will show “Prod” (Product). TheProductLED alsoflashes.

2. Presseither theright or left Up andDown Switchesto

selectaproduct to program.

3. PressSetSwitch andtheOther LED flashes. The left display

shows“LdCo,” andtheright display showsload compen-

sationsetting,andcanbeadjustedwith the right Up and

Down Switches.

4. Pressthe SetSwitch andtheOther LED continuesto flash.

The left display shows“PC,” theright display showsthe

proportional control setting,andcanbeadjustedwith the

right Up andDown Switches.

5. Pressthe SetSwitch andtheOther LED continuesto flash.

The left display shows.“LdAn,” andtheright display shows

loadanticipation setting,andcanbeadjustedwith the right

Up andDown Switches.

6. Pressthe SetSwitch andthe OtherLED continuesto flash.

The left display shows“Filtr,” andthe right display shows

filter cyclessetting,andcanbeadjustedwith the right Up

andDown Switches.

~ 7. Pressthe SetSwitch andthe ProductLED flashes. Press

eitherright or left Up andDown Switchesto selectanother

productto program. Pressandhold the SetSwitch to exit the

programmode,or continueon to thethird level program

mode.

4-3. I ING

8. Also, with the Product LED flashing, pressing the right

Up and Down Switches will access the Idle Mode

parameters. The idle LED will be flashing, the left display

will continue to show “Slct” and the right display shows

“Prod.” Pressing the Set Switch allows the operator to

program the idle parameters (See Section 4-3).

The Idle Mode must be enabled for the operator to accessthis

mode.

1. While in the SecondProgram Mode, and the Product LED

isflashing, press the right Up and Down Switches to select

the idle mode items. The Idle LED will be flashing.

2. Press the Set Switch and the Time LED flashes, the left

display shows “idle,” and the right display shows “ON or

OFF”. Pressing the right Up and Down Switches to turn

idle on or off.

3. Press the Set Switch and the Time LED flashes. The left

display shows “Auto” and the right display shows

automatic idle time. Adjust the automatic idle time with

the right Up and Down Switches, and to disable the auto

idle feature set time to “OFF.”

4. Press the Set Switch and the Temperature LED flashes.

The left display shows “F” or “C”, and the right display

showsthe idle temperature setpoint, which canbe adjusted

with the right Up and Down Switches.

5. Press Set Switch and the Product LED flashes. Press and

hold the Set Switch to exit the program mode or continue

to the third level program mode.

The Third Level Program Mode allows the operator to enable,

or disable “global” setpoints, program Fahrenheit or Celcius,

probe calibration, alarm duration, and hold duration.

1. While in the third level program mode, press and hold Exit

Melt and Temp switches until the buzzer sounds, and the

left display flashes “glob” and OF”, and the right display

shows “ON” or “OFF.” Pressing the right Up and Down

Switches enables, or disables the global setpoint

programming.

2. Press the Set Switch and the left displays shows “deg”

and the right display shows “OF” or ““C.” Pressing the

right Up and Down Switches allows the operator to select

Fahrenheit, or Celcius.

30113Q21303

3. Press the Set Switch and the left display flashes “Prob”

and “Calib.” The right display shows the actual pot

temperature, and the right Up and Down Switches are

used for calibration.

4. Press the Set Switch and the left display flashes “AL”

and “dur.” The right display shows the duration of this

alarm at the end of a cook cycle, and can be adjusted with

the right Up and Down Switches.

5. Press the Set Switch and the left display flashes “Hold”

and “dur.” The left display shows the duration of the hold

alarm at the end of the hold cycle, and can be adjusted

with the right Up & Down Switches.

6. Press and hold the Set Switch to exit the program mode.

The Special Program Mode allows the operator to initialize

the program, or to perform an input/output test.

1. Turn Power Switch off, then press and hold the right Up

and Down Switches while turning power switch back on.

The left display shows “init” and the right displays shows

“sgs.” Press and hold the right Up or Down Switch for

five secondsto initialize all settings. SpecialProgram Mode

is automatically exited if initialize is done.

2. While in the Special Program Mode, press the Set Switch

and the left display shows “10” and the right display shows

“test,” then they go blank. By pressing all switches,

enables all LED’s and displays. Pressing temp. switch

turns on heat. Press and hold Set Switch exits SpecialPro-

gram Mode.

Otros manuales para 301

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Freidora de Henny Penny

Henny Penny

Henny Penny FM05-032-G Manual de usuario

Henny Penny

Henny Penny PFG-690 Manual de usuario

Henny Penny

Henny Penny Evolution Elite EEE-154 Manual de usuario

Henny Penny

Henny Penny PFE-500 Manual de usuario

Henny Penny

Henny Penny PFG-691 Manual de usuario

Henny Penny

Henny Penny Evolution Elite Manual de usuario

Henny Penny

Henny Penny 291 Instrucciones de funcionamiento

Henny Penny

Henny Penny 580 KFC Manual de usuario

Henny Penny

Henny Penny LOV LVE-102 Manual de usuario

Henny Penny

Henny Penny 8000 Computron Manual del propietario

Henny Penny

Henny Penny F5 Manual de usuario

Henny Penny

Henny Penny PFE-591 Manual de usuario

Henny Penny

Henny Penny 520 Manual de usuario

Henny Penny

Henny Penny PFE-590 Manual de referencia

Henny Penny

Henny Penny OFG-392 Manual de usuario

Henny Penny

Henny Penny OFE-341 Manual de usuario

Henny Penny

Henny Penny 500 Manual de usuario

Henny Penny

Henny Penny OE 301 Manual de usuario

Henny Penny

Henny Penny LVE-102 Manual de usuario

Henny Penny

Henny Penny LOV LVE-100 Series Manual de usuario

Henny Penny

Henny Penny 500 Manual de usuario

Henny Penny

Henny Penny PFE-591 Manual de usuario

Henny Penny

Henny Penny 500 Manual de usuario

Henny Penny

Henny Penny OFE-342 Manual de usuario

Manuales populares de Freidora de otras marcas

Innsky

Innsky 55SA1US Manual de usuario

Falcon

Falcon G350/11 Guía del usuario

GoWISE USA

GoWISE USA GW22612 Manual de usuario

Wolf

Wolf IF15/S Manual de usuario

Electrolux

Electrolux Thermetic 9CHG583284 Guía rápida

Gourmia

Gourmia GAF799 Manual de usuario

DeLonghi

DeLonghi D677UX Manual de usuario

SEVERIN

SEVERIN DEEP FRYER - Guía del usuario

Toastmaster

Toastmaster TMFG18-NAT Manual de usuario

Domo

Domo DO465FR Manual de usuario

Farberware

Farberware FBW FT 43721 B Manual de usuario

GERMANICA

GERMANICA GEAF5L3LD Manual de usuario

Roller Grill

Roller Grill MF 120 R Manual de operación

Philips

Philips HD9211 Manual de usuario

Linea 2000

Linea 2000 Domo DO536FR Manual de usuario

Lakeland

Lakeland 31796 Manual de usuario

Dash

Dash Tasti-Crisp DFAF755 Manual de usuario

Fagor

Fagor F-200 Manual de usuario