Helios Power Solutions PF 1 6K Manual de usuario

PF 1 6K/10K Online UPS

Uninterruptible Power Supply System

Version: 1.3

User Manual

Please comply with all warnings and operating

instructions in this manual strictly. Save this

manual properly and read carefully the following

instructions before installing the unit. Do not

operate this unit before reading through all

safety information and operating instructions

carefully.

Table of Contents

1. SAFETY AND EMC INSTRUCTIONS ................................................................................................. 1

1-1. TRANSPORTATION AND STORAGE...............................................................................................................1

1-2. PREPARATION.......................................................................................................................................1

1-3. INSTALLATION ......................................................................................................................................1

1-4. CONNECTION WARNINGS ...............................................................................................................2

1-5. OPERATION .........................................................................................................................................3

1-6. STANDARDS .........................................................................................................................................3

2. INSTALLATION AND OPERATION .................................................................................................. 4

2-1. UNPACKING AND INSPECTION ...................................................................................................................4

2-2. REAR PANEL VIEW.................................................................................................................................4

2-3. RACK/TOWER INSTALLATION (ONLY FOR RT MODEL) ......................................................................................6

2-4. SINGLE UPS INSTALLATION .....................................................................................................................7

2-5. UPS INSTALLATION FOR PARALLEL SYSTEM..................................................................................................9

2-6. SOFTWARE INSTALLATION .....................................................................................................................11

3. OPERATIONS................................................................................................................................ 12

3-1. BUTTON OPERATION ............................................................................................................................12

3-2. LED INDICATORS AND LCD PANEL ..........................................................................................................12

3-3. AUDIBLE ALARM..................................................................................................................................13

3-4. SINGLE UPS OPERATION ......................................................................................................................14

3-5. PARALLEL OPERATION ..........................................................................................................................17

3-6. ABBREVIATION MEANING IN LCD DISPLAY.................................................................................................19

3-7. LCD SETTING ....................................................................................................................................19

3-8. OPERATING MODE/STATUS DESCRIPTION .................................................................................................25

3-9. FAULT CODE ......................................................................................................................................28

3-10. WARNING INDICATOR ........................................................................................................................28

3-11 WARNING CODE ................................................................................................................................28

4. TROUBLE SHOOTING ................................................................................................................... 29

5. STORAGE AND MAINTENANCE..................................................................................................... 30

5-1. STORAGE ..........................................................................................................................................30

5-2. MAINTENANCE....................................................................................................................................30

6. SPECIFICATIONS ......................................................................................................................... 31

1. Safety and EMC instructions

Please read carefully the following user manual and the safety instructions before installing the unit or using

the unit!

1-1. Transportation and Storage

Please transport the UPS system only in the original package to protect against shock and

impact.

The UPS must be stored in the room where it is ventilated and dry.

1-2. Preparation

Condensation may occur if the UPS system is moved directly from cold to warm environment.

The UPS system must be absolutely dry before being installed. Please allow at least two hours for the

UPS system to acclimate the environment.

Do not install the UPS system near water or in moist environments.

Do not install the UPS system where it would be exposed to direct sunlight or nearby heater.

Do not block ventilation holes in the UPS housing.

1-3. Installation

Do not connect appliances or devices which would overload the UPS (e.g. big motor-type

equipment)) to the UPS output sockets or terminal.

Place cables in such a way that no one can step on or trip over them.

Do not block air vents in the housing of UPS. The UPS must be installed in a location with good

ventilation. Ensure enough space on each side for ventilation.

UPS has provided earthed terminal, in the final installed system configuration, equipotential

earth bonding to the external UPS battery cabinets.

The UPS can be installed only by qualified maintenance personnel.

An appropriate disconnect device as short-circuit backup protection should be provided in the

building wiring installation.

An integral single emergency switching device which prevents further supply to the load by the

UPS in any mode of operation should be provided in the building wiring installation.

Connect the earth before connecting to the building wiring terminal.

Installation and Wiring must be performed in accordance with the local electrical laws and

regulations.

1-4. Connection Warnings

•In accordance with safety standard EN-IEC 62040-1, installation has to be provided with a《Backfeed

Protection》system, as for example a contactor, which will prevent the appearance of voltage or

dangerous energy in the input mains during a mains fault. There is no standard backfeed protection

inside of the UPS. Please isolate the UPS before working according to below diagram. The isolation

device must be able to carry the UPS input current.

External backfeed protection wiring

There can be no derivation in the line that goes from the «Backfeed Protection» to the UPS, as

the standard safety would be infringed.

•Warning labels should be placed on all primary power switches installed in places away from the device

to alert the electrical maintenance personnel of the presence of a UPS in the circuit. The label will bear

the following or an equivalent text:

•This UPS should be connected with TN earthing system.

•The power supply for this unit must be single-phase rated in accordance with the equipment nameplate.

It also must be suitably grounded.

WARNING

HIGH LEAKAGE CURRENT

EARTH CONNECTION ESSENTIAL

BEFORE CONNECTING SUPPLY

Before working on this circuit

-Isolate Uninterruptible Power System (UPS)

-Then check for Hazardous Voltage between all

terminals including the protective earth.

Risk of Voltage Backfeed

•Use of this equipment in life support applications where failure of this equipment can reasonably be

expected to cause the failure of the life support equipment or to significantly affect its safety or

effectiveness is not recommended. Do not use this equipment in the presence of a flammable anesthetic

mixture with air, oxygen or nitrous oxide.

•Connect your UPS power module’s grounding terminal to a grounding electrode conductor.

•The UPS is connected to a DC energy source (battery). The output terminals may be live when the UPS

is not connected to an AC supply.

1-5. Operation

Do not disconnect the earth conductor cable on the UPS or the building wiring terminals in any

time since this would cancel the protective earth of the UPS system and of all connected loads.

The UPS system features its own, internal current source (batteries). The UPS output sockets or

output terminal blocks may be electrically live even if the UPS system is not connected to the building

wiring outlet.

In order to fully disconnect the UPS system, first press the “OFF” button and then disconnect the

mains.

Ensure that no liquid or other foreign objects can enter into the UPS system.

The UPS can be operated by any individuals with no previous experience.

1-6. Standards

* Safety

IEC/EN 62040-1

* EMI

Conducted Emission...............................:IEC/EN 62040-2

Category C3

Radiated Emission..................................:IEC/EN 62040-2

Category C3

*EMS

ESD.........................................................:IEC/EN 61000-4-2

Level 4

RS........................................................ ...:IEC/EN 61000-4-3

Level 3

EFT......................................................... :IEC/EN 61000-4-4

Level 4

SURGE................................................... :IEC/EN 61000-4-5

Level 4

CS........................................................... :IEC/EN 61000-4-6

Level 3

Power-frequency Magnetic field.............. :IEC/EN 61000-4-8

Level 4

Low Frequency Signals............................:IEC/EN 61000-2-2

Warning: This is a product for commercial and industrial application in the

second environment-installation restrictions or additional measures may be

needed to prevent disturbances.

2. Installation and Operation

There are two different types of online UPS: standard and long-run models. Please refer to the following

model table.

Model

Type

Model

Type

6K/6KRT

standard model

6KL/6KRTL

Long-run model

10K/10KRT

10KL/10KRTL

We also offer optional parallel function for these two types by request. The UPS with parallel function is

called as “Parallel model”. We have described detailed installation and operation of Parallel Model in the

following chapter.

2-1. Unpacking and Inspection

Unpack the package and check the package contents. The shipping package contains:

● One UPS

●One user manual

● One monitoring software CD

●One RS-232 cable (option)

●One USB cable

●One parallel cable (only available for parallel model)

●One share current cable (only available for parallel model)

● One battery cable (option)

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged

during transportation. Do not turn on the unit and notify the carrier and dealer immediately if there is any

damage or lacking of some parts. Please keep the original package in a safe place for future use.

2-2. Rear Panel View

Tower Model

Diagram 1: 6K/10K Diagram 2: 6KL/10KL

Rear Panel Rear Panel

1) Share current port (only available for parallel model)

2) Parallel port (only available for parallel model)

3) External battery connector

4) Intelligent slot

5) RS-232 communication port

6) USB communication port

7) Emergency power off function connector (EPO

connector)

8) Maintenance bypass switch

9) Cooling fan

10) Input circuit breaker

11) Output terminals

12) Ground

13) Input terminals

RT Model

Diagram 1: UPS Rear Panel

Diagram 2: 2U battery pack Diagram 3: 3U battery pack

1) Share current port (only available for parallel model)

2) Parallel port (only available for parallel model)

3) External battery connector

4) Intelligent slot

5) RS-232 communication port

6) USB communication port

7) Emergency power off function connector (EPO connector)

8) Input circuit breaker

9) Output terminals

10) Ground

11) Input terminals

12) Cooling Fan

13) External maintenance bypass switch port

14) Battery pack output circuit breaker

15) External battery connector

2-3. Rack/Tower Installation (only for RT model)

2-3-1 Tower Installation

The UPS system is shipped with two sets of feet and 6 extensions (2 short extensions plus 4 long extensions)

that can be used to tower install the UPS module in 2U or UPS module with one battery bank in 4U.

Install UPS module in 2U

Assemble two feet and one short extension as one tower stand shown in step 1. Align the two stands

approximately 35cm apart in step 2. Then, put UPS module in the stands as shown in step 3.

Step 1 Step 2 Step 3

Install UPS module and one battery bank in 4U

Assemble two feet and two long extensions as one tower stand shown in step 1. Align the two stands

approximately 35cm apart in step 2. Then, put UPS module and battery bank in the stands as shown in step

Step 1 Step 2 Step 3

2-3-2 Rack Installation

Please follow below steps to mount UPS into 19”rack or rack enclosure.

Step 1: Attach mounting ears to the side mounting

holes of UPS using the screws provided and the ears

should face forward. Please refer to chart 1.

Chart 1

Step 2: Lift the UPS module and slide it into rack

enclosure. Attach the UPS module to the rack with

screws, nuts and washers (user-provided) through

its mounting ears and into the rack rails. Please

refer to chart 2.

Chart 2

2-4. Single UPS Installation

Installation and wiring must be performed in accordance with the local electric laws/regulations and execute

the following instructions by professional personnel.

1) Make sure the mains wire and breakers in the building are enough for the rated capacity of UPS to

avoid the hazards of electric shock or fire.

NOTE: Do not use the wall receptacle as the input power source for the UPS, as its rated current is less than

the UPS’s maximum input current. Otherwise the receptacle may be burned and destroyed.

2) Switch off the mains switch in the building before installation.

3) Turn off battery breaker before installation (only for RT model).

4) Turn off all the connected devices before connecting to the UPS.

5) Prepare wires based on the following table:

Model

Wiring spec (AWG)

Input

Output

Battery

Ground

6K/6KRT

6KL/6KRTL

10K/10KRT

10KL/10KRTL

NOTE 1: The cable for 6K/6KL/6KRT/6KRTL should be able to withstand over 50A current. It is

recommended to use 10AWG or thicker wire for safety and efficiency.

NOTE 2: The cable for 10K/10KL/10KRT/10KRTL should be able to withstand over 63A current. It is

recommended to use 8AWG or thicker wire for safety and efficiency.

NOTE 3: The selections for color of wires should be followed by the local electrical laws and

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario