Heden NeptoLux 3K Manual de usuario

Emergency escape lighting system

Installation instruction NEPTO 3K

Oy Hedengren Security Ab, +358 (0)207 638 000, sales +358 (0)207 638 635,

security@hedengren.fi, tuotetuki@hedengren.fi, hedengrensecurity.fi, neptolux.fi

NEPTOLUX 
 
2 
LIST OF CONTENTS 
1. GENERAL......................................................................................................................................................4 
 STANDARDS...............................................................................................................................................5 
 CABLES AND CABLE SHEATHINGS.................................................................................................................5 
 INSTALLATION ENVIRONMENT ......................................................................................................................5 
2. HOUSING.......................................................................................................................................................6 
 INSTALLATION.............................................................................................................................................6 
3. ADDRESS BUS .............................................................................................................................................8 
 PRINCIPLE..................................................................................................................................................8 
 INSTALLATION OF EXIT AND ROUTE LIGHTS ...................................................................................................8 
 LIGHTS ....................................................................................................................................................12 
3.3.1. Route lights .....................................................................................................................................12 
Route light NFW68-O ............................................................................................................................................12 
Route light NFW68-C.............................................................................................................................................12 
Guide light NFW68-0.............................................................................................................................................13 
Guide light NFW89-C.............................................................................................................................................13 
3.3.2. Emergency exit lighting...................................................................................................................16 
Emergency exit light NFW20-x..............................................................................................................................16 
Emergency exit light NFW40-x..............................................................................................................................17 
Emergency exit light NAH70-x...............................................................................................................................18 
Step lighting unit, NA55.........................................................................................................................................19 
 NEPTO-IO..............................................................................................................................................20 
4. NL-KLG KEYPAD PANEL...........................................................................................................................23 
 GENERAL.................................................................................................................................................23 
 INSTALLATION...........................................................................................................................................24 
 CONNECTION ...........................................................................................................................................25 
 SETTINGS ................................................................................................................................................26 
 START-UP ................................................................................................................................................27 
5. NEPTO-3K CONNECTIONS........................................................................................................................28 
5.1.1. Fuses...............................................................................................................................................29 
5.1.2. Relay outputs ..................................................................................................................................29 

NEPTOLUX 
 
 
 
3 
5.1.3. Voltage output 24DC.......................................................................................................................29 
5.1.4. Inputs...............................................................................................................................................30 
5.1.5. Installing an extra communication card...........................................................................................30 
5.1.6. Nepto 3K networking.......................................................................................................................30 
6. TCH-B200 ADDRESS' PROGRAMMING UNIT..........................................................................................33 
7. CABLE LENGTH .........................................................................................................................................34 
 ILLUMINATION POINTS ...............................................................................................................................34 
7.1.1. Equidistant lighting units .................................................................................................................34 
7.1.2. Examples.........................................................................................................................................35 
Single-storey building ............................................................................................................................................35 
Multi-storey building...............................................................................................................................................36 
 OTHER EQUIPMENT...................................................................................................................................37 
7.2.1. Equidistant devices .........................................................................................................................39 
The minimum operating voltage 6.5V....................................................................................................................39 
The minimum operating voltage 7.5V....................................................................................................................39 
The minimum operating voltage 8.5V....................................................................................................................40 
7.2.2. Devices at cable ends.....................................................................................................................42 
The minimum operating voltage 6.5V....................................................................................................................42 
The minimum operating voltage 7.5V....................................................................................................................43 
The minimum operating voltage 8.5V....................................................................................................................44 
8. TECHNICAL INFORMATION ......................................................................................................................45 
 CENTRE...................................................................................................................................................45 
9. FAULT FINDING..........................................................................................................................................46 
 RS485 DATA CONNECTION.......................................................................................................................46 
 EARTH LEAKAGE.......................................................................................................................................46 
9.2.1. Interference in the operating device data line (potential wrong code, tamper alarm).....................46 
 LIGHTING BUS...........................................................................................................................................46 
9.3.1. Input voltage....................................................................................................................................46 
9.3.2. The line's data communication........................................................................................................47 
9.3.3. Overcurrent/double address............................................................................................................47 

NEPTOLUX

General

1. General

These instructions cover the installation of the NEPTO-3K system.

The features and technical values, e.g. number of lines, is dependent on the centre model.

NEPTOLUX

General

Standards

The system complies with device testing, fault monitoring and reporting according to standards SFS-EN

50172 and ATS 62034 either locally or remotely.

Cables and cable sheathings

The cables used must be equipped with cable sheathings. All the calculations in these instructions have

been done using a 0.8-mm conductor diameter.

The cable type used is KLMA 2x0.8+0.8 or ELQYB 2x1.0 mm, conductor diameter 0.8 mm, conductor

pair's loop resistance 74/km, conductor pair's capacitance 60nF/km.

The insulation resistance between the conductors and earth potential must be > 500kIf the insulation

resistance is lower, uncontrolled earth currents reach the system and cause interference. Problems may

be caused by e.g. metal mounting boxes, in which the cable sheathing is fixed, if the box is earthed to

the building frame with connecting screws.

All cable sheathings must be fixed to the central housing. Therefore, e.g. the cable sheathings at the

end of a handset are fixed to the conductor's S pin (shield). The protective sheathing must be extended

into the unit switching point of each address bus.

The cable running between the transformer and the centre must be type MSK 2x1mm. The cable must

be less than 1 m long. The cable comes with the centre.

Installation environment

The operating conditions of the system and the attached components must be taken into account when

the installation environment is chosen.

NEPTOLUX

Housing

2. Housing

Installation

The weight of the housing must be taken into account when it is fixed onto a wall.

•Drill 4 pcs. 6 mm2 holes for the anchor fixings. Depth of hole must be 20-25mm. Position

of holes. See image.

•Fix anchor fixings.

•Screw 4mm. 4.2 mm screws into the anchor fixings, ensuring they stay fixed.

•Lift the housing onto the wall directing the screws to the screw grooves in the housing.

•Hang the housing on the screws.

•Tighten the screws.

•Pull the cables between the wall and the housing. Thread the cables through the cable

feedthrough. Please note: The feedthrough on the bottom of the housing is for the transformer

cable. The feedthroughs at the top are for other cables.

•Shorten the cables before the installation.

•Peel the cables for installation.

•The insulation resistance must be measured before the connection cable is attached.

•The insulation resistance must be measured on every connection cable, including the sheathing,

against protective earth. The insulation resistance must be >1M.

•After this the cable sheathing can be fixed to the housing's switching point. See image.

NEPTOLUX

Housing



10A mA COM V-

NEPTOLUX

Address bus

3. Address bus

Principle

The system's lighting units and bus units are addressable, smart units equipped with the own batteries

(lighting). The centre polls the units over approximately 0.75-s periods per address. Thus the units (127

pcs) in the entire bus are checked over < 100s. The lighting units also work as independent units if the

central cable snaps.

The address for all the previously unused lighting units is 127 (factory setting). The lighting units

must be programmed with a TCH-B200 programming device before installation into the base.

The units do not need to be in the bus in the address order.

The maximum length of the address bus is 1 km, the conductor's loop resistance is max 74The

cable's conduction capacitance must be <0.7F.

A maximum of 127 units can be connected to one address bus, depending on the power consumption of

the unit. The unit's power consumption also restricts the cable distance.

Installation of exit and route lights

The common mounting base for the lighting units is Hochiki's YBN-R/3.

When the common mounting base is installed, the direction of the pip in the base must

be noted. The pip should point to the right at a 90° angle in relation to the exit direction.

For a two-sided sign, the pattern pointing to the left determines the direction of the pip in

the base. The base has a small adjustment range for the angle. A template should be used for

drilling.

All equipment must be attached to an even surface to ensure that the unit does not bend.

The base can be attached to the ceiling or the wall.

The address bases are attached with screws with a 3-mm diameter.

Do not tighten the screws too tight to ensure that the plastic does not crack.

The bus cable must be installed for each lighting unit. The bus can be cabled to a star network as well

as via each lighting unit. The bus cable's sheathing is attached to the frame of the centre.

Fixing YBN-R/3 base

1 bus +

2 bus +

3 cable sheathing

4 not in use

5 bus -

6 bus -

NEPTOLUX

Address bus

Installation of emergency lights to base YBN-R/3

Tighten the lighting unit to the common mounting base so that the pip on the cap is fixed in a "quarter

to" position in relation to the mounting base's corresponding pip. After this, keep hold of the cap and

screw clockwise until the lighting unit locks into place.

NFW 68/89

NEPTOLUX

Address bus

Fixing the signpost plastic to the signpost's frame

Tabla de contenidos

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario