Heatmaster ENVIRO Instrucciones de funcionamiento
ALL PLUMBING AND ELECTRICAL WORK TO BE CARRIED OUT BY A QUALIFIED TECHNICIAN
Heatmaster Pty Ltd
Email: sales@heatmaster.com.au
Website: www.heatmaster.com.au
ACN 006 442 717 ABN 64 641 709 587
FOR FURTHER INFORMATION PLEASE
CONTACT YOUR LOCAL DEALER.
ALL PLUMBING AND ELECTRICAL WORK
TO BE CARRIED OUT BY A QUALIFIED
TECHNICIAN
The Trouble shooting - Heatmaster enviro
Issue
Cause
Solution
Unit not starting
1. Insufficient power
2. Igniters and or sensor is
shorting out
3. Desired temperature is set
below room temperature
Turn on isolation switch
Clean soot off
igniters/sensor and make
sure they are running
parallel with burner
(see below)
Increase desired room
temperature
Turning on 1 - 3 sec
1. Soot build up on flame
sensor
2. Insufficient power
Clean flame sensor with
a dry cloth
Make sure no extension
cord or power board are
being used.
Be sure no pebbles
or the pebble racks
come in contact with
the two igniters
(running to the right)
and the flame sensor
(running to the left)
This may cause the unit
to malfunction
ALL PLUMBING AND ELECTRICAL WORK TO BE CARRIED OUT BY A QUALIFIED TECHNICIAN
Heatmaster Pty Ltd
Email: sales@heatmaster.com.au
Website: www.heatmaster.com.au
ACN 006 442 717 ABN 64 641 709 587
FOR FURTHER INFORMATION PLEASE
CONTACT YOUR LOCAL DEALER.
ALL PLUMBING AND ELECTRICAL WORK
TO BE CARRIED OUT BY A QUALIFIED
TECHNICIAN
Turning on 5 sec
1. Insufficient air
2. Insufficient gas pressure
Make sure that air intake
flue is not crushed
Compressed.
Make sure incoming gas
pressure is sufficient and
there are no blockages or
obstructions.
Turning off after 5-6 min and
then turning back on then off
again
1. Insufficient air
2. Room temperature has
reached desired
temperature
Make sure that flue air
intake is connected to
cowl (may be the case in
brick chimney)
making sure sufficient
clearances are from cowl
to eve, ground, side wall
Increase desired
temperature on remote
control.
The sensors should be kept
clear of pebbles, log or coals
at all times,
They should not be obstructed
in any way.
(see image)
The flame sensor should sit
approx. 10mm off the burner
The igniters should sit approx.
5mm off the burner
ALL PLUMBING AND ELECTRICAL WORK TO BE CARRIED OUT BY A QUALIFIED TECHNICIAN
Heatmaster Pty Ltd
Email: sales@heatmaster.com.au
Website: www.heatmaster.com.au
ACN 006 442 717 ABN 64 641 709 587
FOR FURTHER INFORMATION PLEASE
CONTACT YOUR LOCAL DEALER.
ALL PLUMBING AND ELECTRICAL WORK
TO BE CARRIED OUT BY A QUALIFIED
TECHNICIAN
Flame turning off by itself
1. Remote is on “Auto”
2. Unit goes over desired
temp
Turn remote to manual
Use manual controls on
unit
Unit not turning on when you
have programmed it.
1. Remote on “Manual”
2. Remote power button not
turned “on”
Turn remote to Auto
Turn power button “On”
The enviro remote
should be only on
“auto” mode if you
have programmed
the unit to come on
and off at specific
times
Otherwise it should be
on “manual” mode.
ALL PLUMBING AND ELECTRICAL WORK TO BE CARRIED OUT BY A QUALIFIED TECHNICIAN
Heatmaster Pty Ltd
Email: sales@heatmaster.com.au
Website: www.heatmaster.com.au
ACN 006 442 717 ABN 64 641 709 587
FOR FURTHER INFORMATION PLEASE
CONTACT YOUR LOCAL DEALER.
ALL PLUMBING AND ELECTRICAL WORK
TO BE CARRIED OUT BY A QUALIFIED
TECHNICIAN
Issue
Cause
Solution
Unit not coming on (no spark,
flames or fans)
1. Power not turned on
2. Fuse has blown
Turn on isolation switch
Remove and replace fuse
Issue
Cause
Solution
Unit not coming on (no spark,
flames or fans)
1. No power
2. Manual control not
plugged in or is damaged
3. Fuse has blown
Ensure manual control is
plugged in (see image
below) and not damaged
Turn on isolation switch
Remove and replace fuse
The fuse is found in a
plastic protective
case at the bottom
left hand side of the
unit.
The fuse is 1.5AMP
IMPORTANT
Make sure the isolation
switch is turned off
before removing.
ALL PLUMBING AND ELECTRICAL WORK TO BE CARRIED OUT BY A QUALIFIED TECHNICIAN
Heatmaster Pty Ltd
Email: sales@heatmaster.com.au
Website: www.heatmaster.com.au
ACN 006 442 717 ABN 64 641 709 587
FOR FURTHER INFORMATION PLEASE
CONTACT YOUR LOCAL DEALER.
ALL PLUMBING AND ELECTRICAL WORK
TO BE CARRIED OUT BY A QUALIFIED
TECHNICIAN
Issue
Cause
Solution
Manual controls not working
1. Manual control not
plugged in or is damaged
2. Fuse has blown
Ensure manual control is
plugged in (see image
above) and not damaged
Turn on isolation switch
Remove and replace fuse
You can hear the unit try and
spark but there is not visual
spark inside the unit.
1. One or both igniters are
arching out
2. Igniters not plug in
correctly
3. Igniters damaged
Ensure igniters are
correctly plugged in and
rubber coating is sealed
Replace igniters
The igniters are found at the front of
the blue box and the flame sensor at
the rear.
Make sure the plastic/rubber protective
coating is sealed.
Be sure to
plug in the
manual
control prior
to attaching
the fascia.
ALL PLUMBING AND ELECTRICAL WORK TO BE CARRIED OUT BY A QUALIFIED TECHNICIAN
Heatmaster Pty Ltd
Email: sales@heatmaster.com.au
Website: www.heatmaster.com.au
ACN 006 442 717 ABN 64 641 709 587
FOR FURTHER INFORMATION PLEASE
CONTACT YOUR LOCAL DEALER.
ALL PLUMBING AND ELECTRICAL WORK
TO BE CARRIED OUT BY A QUALIFIED
TECHNICIAN
Issue
Cause
Solution
Unit not sparking
1 Igniters are shorting out
2 Blockage in fluing
Check igniter leads from blue
box to unit making sure the
plastic coating is not damaged.
Clean flues and cowl, make
sure there is nothing blocking
or restricting air intake and
exhaust.
Issue
Cause
Solution
Flames running on low only
1 Modulating wires are
loose or not
connected properly
Ensure wires are
connected properly (see
image below) and not
damaged
The white and orange
modulating wires are
found at the top of the Gas
valve (see image left)
Make sure they are both
connected properly and not
damaged.
Otros manuales para ENVIRO
3
Otros manuales de Chimenea de interior de Heatmaster
Heatmaster
Heatmaster Seamless Manual de usuario
Heatmaster
Heatmaster enviro 17 Manual de usuario
Heatmaster
Heatmaster A450 Manual de usuario
Heatmaster
Heatmaster HVF36-BB Manual de usuario
Heatmaster
Heatmaster ENVIRO Manual de usuario
Heatmaster
Heatmaster HM2-IPI-ECO Manual de usuario
Heatmaster
Heatmaster HVF-36 Manual de usuario
Heatmaster
Heatmaster Oak Ridge Creek 24” Manual de usuario
Heatmaster
Heatmaster SBS-18NG Manual de usuario
Heatmaster
Heatmaster A series Manual de usuario
