Heatilator A36R Manual de usuario

Heatilator • A36/42R, A36/42RH • Installers Manual • 4017-259 • Rev I • 06/29/15 1

WOODBURNING FIREPLACE

Fire Risk.

WARNING

For use with solid wood fuel only.

Other fuels may overre and generate

poisonous gases (i.e. carbon monoxide).

Model(s):

Installation Manual

Installation and Fireplace Setup

WARNING

HOT SURFACES!

Glass and other surfaces are hot during

operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ammable

materials.

• Keep clothing, furniture, draperies and other ammable

materials away.

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

A36R, A36RH

A42R, A42RH

NOTICE: DO NOT discard this manual!

• DO NOT store or use gasoline or other am-

mable vapors and liquids in the vicinity of this

or any other appliance.

• DO NOT overre. Overring will void your

warranty.

• Comply with all minimum clearances to com-

bustibles as specied. Failure to comply may

cause house re.

WARNING: If the information in these

instructions is not followed exactly, a re

or explosion may result causing property

damage, personal injury, or death.

Installation and service of this

appliance should be performed by

qualied personnel. Hearth & Home

Technologies recommends HHT

Factory Trained or NFI certified

professionals.

Heatilator • A36/42R, A36/42RH • Installers Manual • 4017-259 • Rev I • 06/29/15

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Indicates practices which may cause damage to the replace or to property.

Table of Contents

1 Product Specic & Important Safety Information

A. Fireplace Certication 4

B. Non-Combustible Materials 4

C. Combustible Materials 4

2 Getting Started

A. Typical Fireplace System 5

B. Design and Installation Considerations 6

1. Selecting Fireplace Locations 6

2. Locating Fireplace & Chimney 7

C. Tools and Supplies Needed 8

D. Inspect Fireplace and Components 8

E. Fireplace System Requirements 8

3 Framing and Clearances

A. Fireplace Dimensions 9

B. Clearances 10

Minimum Clearances to Combustibles 10

C. Construct the Chase 11

D. Frame the Fireplace 12

E. Secure and Level the Fireplace 12

F. Protective Metal Hearth Strips 13

G. Outside Air Kit (optional) 14

4 Chimney and Termination Requirements

A. Chimney Requirements 15

B. Offsets/Returns 16

C. Termination Requirements 17

5 Chimney Installation

A. Typical Chimney System 18

B. Assemble Chimney Sections 19

C. Secure Offset/Return 20

D. Install Ceiling Firestops 20

E. Install Attic Insulation Shield 21

F. Roof Penetration 22

G. Install Chase/Chase Top 22

H. Termination Cap Requirements 23

I. Install Termination Cap 23

6 Shrouds

A. Radiation Shield 25

B. Field Constructed Shrouds 25

1. Open Top Shroud 25

2. Mailbox Style Shroud 26

3. Roofed Style Shroud 26

7 Finishing

A. Finishing Material 27

B. Hearth Extension, Building and Finishing 28

1. Fireplace Installed Flush on the Floor

and Hearth Extension Raised to Bottom

of Firebox Opening 29

2. Raised Hearth Extension and Raised Fireplace 30

3. Fireplace Opening and Hearth Extension Flush

with the Floor 31

C. Non-Combustible Sealant Material 31

D. Mantel and Wall Projections 32

E. Sidewalls/Surrounds 33

8 Fireplace Setup

A. Gas Log/Lighter Provision 34

B. Wood Burning Inserts 34

9 Reference Materials

A. Chimney Components 35

B. Optional Components 39

►

Heatilator • A36/42R, A36/42RH • Installers Manual • 4017-259 • Rev I • 06/29/15 3

Customer:

Lot/Address

Model (circle one): A36R A36RH

A42R A42RH

YES IF NO, WHY?

Dealer/Distributor Phone #

Serial #:

Roof flashing installed.

Termination installed.

Fireplace Install

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjuction with, not instead of, the instructions contained in this installation

manual.

Date Installed:

Location of Fireplace:

Installer:

WARNING! Risk of Fire or Explosion! Failure to install fireplace acording to these instructions can lead to a fire or

explosion.

Verified that the chase is insulated and sealed. (Pg. 11)

Verified clearances to combustibles. (Pg. 10)

Fireplace is leveled and secured. (Pg. 12)

Hearth extension size/height decided. (Pg. 28)

Chimney configuration complies with diagrams.

Chimney installed, locked and secured in place with proper clearance.

Chimney air kit installed.

Firestops installed.

Protective hearth strips installed per manual requirements. (Pg.13)

Outside air kit installed. (Pg 14)

Chimney Section 4 & 5 (Pg. 15)

Attic insulation shield installed.

Shrouds Section 6 (Pg. 25)

Shroud is installed properly per instructions.

Comments communicated to party responsible

4017-261 • Rev A • 2-19-13

• Photographing the installation and copying this checklist for your file.

Combustible materials not installed in non-combustible areas.

All packaging and protective materials removed.

Optional doors properly installed.

Refractory installed correctly.

Grate is properly installed.

Firescreen installed properly.

(Builder/Gen. Contractor) (Installer) (Date)

Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:

Manual bag and all of its contents are removed from the fireplace and given to the party

responsible for use and operation.

• That this checklist remain visible at all times on the fireplace until the installation is complete.

__________________________ by ______________________on _________

Hearth extension installed per manual requirements.

Verified all clearances meet installation manual requirements.

Mantels and wall projections comply with installation manual requirements.

Fireplace Setup Section 8 (Pg. 34)

Hearth & Home Technologies recommends the following:

Finishing Section 7 (Pg. 27)

Heatilator • A36/42R, A36/42RH • Installers Manual • 4017-259 • Rev I • 06/29/15

WARNING! Risk of Fire! Hearth & Home Technologies

disclaims any responsibility for, and the warranty and

agency listing will be voided by the following actions.

DO NOT:

• installoroperatedamagedreplace

• modifyreplace

• install other than as instructed by Hearth & Home

Technologies

• operate the fireplace without fully assembling all

components

• overre

• installunventedgaslogset

• installanycomponentnotapprovedbyHearth&Home

Technologies

• installpartsorcomponentsnotListedorapproved

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. For

assistance or additional information, consult a qualied

installer, service agency or your dealer.

B. Non-Combustible Materials

• Materials which will not ignite and burn, composed of

any combination of the following:

- Steel - Iron

- Brick - Tile

- Concrete - Slate

- Glass - Plasters

• Materials reported as passing ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube

Furnace at 750° C

C. Combustible Materials

• Materials made of or surfaced with any of the following

materials:

- Wood - Compressed paper

- Plant bers - Plastic

- Plywood/OSB - Sheet rock (drywall)

• Any material that can ignite and burn; ame proofed or

not, plastered or un-plastered

1 Product Specic & Important Safety Information

A. Fireplace Certication

This replace may be installed in sleeping rooms. This

is not approved for installation in manufactured homes.

If installed with a gas log set, provisions for the National

Fuel Gas Code must be met.

This replace has been tested and listed for use with

the optional components specied in this manual. These

optional components may be purchased separately and

installed at a later date. An outside air kit, gas insert, gas

log set or gas log-lighter should be installed at the time of

replace installation.

Heatilator is a registered trademark of Hearth & Home

Technologies.

This replace system has been tested and listed in accor-

dance with UL 127 and ULC-S610 standards by Under-

writers Laboratories Inc. for installation and operation in

the United States and Canada.

Heatilator • A36/42R, A36/42RH • Installers Manual • 4017-259 • Rev I • 06/29/15 5

2 Getting Started

A. Typical Fireplace System

Figure 2.1 Typical Fireplace System

)

))

)

Non-combustible

roof flashing maintains

minimum clearance

around chimney

Additional lateral

support for chimney

above roof (or enclosed

in chase) if needed

Ceiling firestop

on floor of attic

Support straps

on rafter support

chimney (not shown)

Termination cap

Chimney penetrates roof

preferably without affecting

roof rafters

Offset & Return (with hanger straps)

Framing headed off

in ceiling joists

Enclosed space above

and around fireplace

Mantel and surround

Decorative facing

and trim

Hearth extension

Factory-built fireplace

Protective metal

hearth strip(s)

Outside

combustion air

Combustible framing/header

on top of V-shaped standoffs

Chimney system

Attic insulation shield must be used

here to keep insulation away from

chimney if attic is insulated

Storm Collar

Chimney Air Kit

Required in

Canada. Outlet

must be no

less than 4 ft.

(1.22 m) off

ground level.

Heatilator • A36/42R, A36/42RH • Installers Manual • 4017-259 • Rev I • 06/29/15

Across a

corner

As a

room

divider

48 in.

(1219 mm)

minimum

Along a wall

A1/2 in. (13 mm) all

configurations

3/4 in. (19 mm) min. air

space from fireplace to

combustible materials. 1/2

in. (13 mm) allowed at

nailing flanges.

Note:

In an exterior chase

or projecting into a

garage

Note: Measurements are FRAMING dimensions only and do

not include drywall either in the cavity or on the interior walls.

*8 in. (203 mm) extra space

included for outside air

connection. If outside air duct

has no bend, this dimension

may be reduced as long as

minimum clearances are met.

Model # A B C D E F G H

in. 51 43 74 7/8 35 3/4 15 3/4 53 23

mm 1295 1092 1902 908 400 1346 584

in. 57 49 77 1/2 38 7/8 18 54 7/8 23

mm 1448 1245 1969 987 457 1394 584

A36

A42

12 in. (305 mm)

Minimum from FP

opening to any

perpendicular wall.

Figure 2.2 Fireplace Locations

NOTICE:

• Illustrationsandphotosreecttypicalinstallationsand

are FORDESIGNPURPOSESONLY.

• Illustrations/diagramsarenotdrawntoscale.

• Actualinstallation/appearancemayvaryduetoindividual

design preference.

• Hearth&HomeTechnologiesreservestherighttoalter

its products.

NOTICE: In addition to these framing dimensions, also

reference the following section: Clearances (Section 3).

NOTICE:

Aminimum3/4in.(19mm)airclearanceatthe

backandsidesofthereplaceassemblymustbe

maintained.

Chimney sections at any level require a 2 in. mini-

mum air space clearance between the framing

and chimney sections.

B. Design and Installation Considerations

NOTICE: Check building codes prior to installation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult insurance carrier, local building inspector, re

ofcials or authorities having jurisdiction over restrictions,

installation inspection and permits.

• Before installing, determine the following:

- Where the replace is to be installed.

- The vent system conguration to be used.

- Gas supply piping.

- Electrical wiring

- Framing and nishing details.

- Whether optional accessories - devices such as a

fan, wall switch or remote control - are desired.

1. Selecting Fireplace Locations

This replace may be used as a room divider, installed

along a wall, across a corner or used in an exterior chase.

See Figure 2.2.

Locating the replace in a basement should be avoided.

Locating near frequently opened doors, central heat

outlets or returns, or other locations of considerable air

movement can affect the performance.

Consideration should be given to these factors before

deciding on a location.

Heatilator • A36/42R, A36/42RH • Installers Manual • 4017-259 • Rev I • 06/29/15 7

2. Locating Fireplace & Chimney

Location of the replace and chimney will affect perfor-

mance.

• Install within the warm airspace enclosed by the building

envelope. This helps to produce more draft, especially

during lighting and die-down of the re.

• Installing the replace in a basement is not recommended.

• Penetrate the highest part of the roof. This minimizes

the effects of wind loading.

• Locate termination cap away from trees, adjacent

structures, uneven roof lines and other obstructions.

• Minimize the use of chimney offsets.

• Consider the replace location relative to oor and ceiling

and attic joists.

• Take into consideration the termination requirements in

Sections 4 and 5.

Marginal Location:

• Below peak

Location NOT recommended:

• Not the highest point of the roof

• Wind loading possible

Multi-level Roofs

Windward

Leeward

Recommended Location:

• Above peak

Recommended:

• Insulated exterior chase

in cooler climates

Recommended Location:

• Above peak

• Inside heated space

Location NOT recommended:

• Too close to tree

• Below adjacent structure

• Lower roof line

• Avoid outside wall

Marginal Location:

• Wind loading possible

Figure 2.3 Recommended Chimney Locations

• Install the outside air kit with the intake facing prevailing

winds during the heating season.

• Ensure adequate outdoor air for all combustion

appliances and exhaust equipment.

• Ensure furnace and air conditioning return vents are not

located in the immediate vicinity of the replace.

• Avoid installing the replace near doors, walkways or

small isolated spaces.

• Recessed lighting should be a “sealed can” design.

• Attic hatches weather stripped or sealed.

• Attic mounted duct work and air handler joints and seams

taped or sealed.

Heatilator • A36/42R, A36/42RH • Installers Manual • 4017-259 • Rev I • 06/29/15

C. Tools and Supplies Needed

Before beginning the installation be sure the following

tools and building supplies are available:

Reciprocating saw Framing material

Pliers Non-combustible sealant

Hammer Gloves

Phillips screwdriver Framing square

Flat blade screwdriver Electric drill and bits

Plumb line Safety glasses

Level Tape measure

1/2-3/4 in. length, #6 or #8 self-drilling screws

Misc. screws and nails

D. Inspect Fireplace and Components

WARNING! Risk of Fire and/or Explosion! Damaged

parts could impair safe operation. DO NOT install dam-

aged,incompleteorsubstitutecomponents.Keepre-

place dry.

• Remove replace and components from packaging and

inspect for damage.

• Vent system components and doors are shipped in

separate packages.

• Report to your dealer any parts damaged in shipment.

• Read all the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum safety

and benet.

E. Fireplace System Requirements

The Heatilator replace system requirements consist of

the following:

• Fireplace

- Refractory (included with replace)

- Firescreen (included with replace)

- Grate (included with replace)

- Hearth Extension (required, sold separately)

• Outside Air System (optional)

- Air Inlet Hood

- Flex

• Chimney System

- Attic Insulation Shield (included with replace)

- Chimney air kit (required in Canada, sold separately)

- Chimney termination cap (required, sold separately)

• Non-combustible nish material

Heatilator • A36/42R, A36/42RH • Installers Manual • 4017-259 • Rev I • 06/29/15 9

3 Framing and Clearances

A. Fireplace Dimensions

Figure 3.1 Fireplace Dimensions

Model # A B C D

in. 36 42 28-1/4 14-1/8

mm 914 1067 718 359

in. 42 48 30-7/8 15-1/2

mm 1067 1219 784 394

A36

A42

4-1/4 in.

(108 mm)

9-5/8 in.

(244 mm)

8-5/8 in.

(219 mm)

13-1/2 in.

(343 mm)

Gas Knockout

Outside

Air

9-1/4 in.

(235 mm)

4-1/4 in.

(108 mm)

9-1/4 in.

(235 mm)

41-3/8 in.

(1051mm)

3-7/8 in.

(92 mm)

7-1/2 in.

(191 mm)

13-1/2 in.

(343 mm)

41-1/4 in.

(1048 mm)

(effective height)

Gas Knockout

Junction

Box

8-3/4 in.

(222 mm)

22-3/4 in.

(578 mm)

10-1/2 in.

(267 mm)

dia.

6-1/4 in.

(159 mm)

37-11/16 in.

(957 mm)

23-3/8 in.

(594 mm)

8-1/16 in.

(205 mm)

Heatilator • A36/42R, A36/42RH • Installers Manual • 4017-259 • Rev I • 06/29/15

B. Clearances

WARNING! Risk of Fire!

You must comply with all minimum air space clearances

tocombustiblesasspeciedinFigure3.2.DO NOT pack

required air spaces with insulation or other materials.

Framing or nishing material used on the front of, or in

frontof,thereplacecloserthantheminimumslistedmust

be constructed entirely of non-combustible materials (i.e.,

steel studs, concrete board, etc.). Failure to comply may

causere.

Figure 3.2 Clearances to Combustible Materials

Minimum Clearances to Combustibles

WITHIN ENCLOSURE AREA

Fireplace to backwall 3/4 in. (19 mm)

Fireplace to sidewall 3/4 in. (19 mm)

Top standoffs to header 0 in. (0 mm)

Door opening to sidewall 12 in. (305 mm)

MANTEL

Mantel minimum height 12 in. (305 mm)

above opening

Maximum mantel depth 12 in. (305 mm)

(insulation)

0 in. to level

of standoffs

Attic

Insulation

Shield

(ceiling)

(roof)

(attic)

(ceiling)

Ceiling Firestop

Offset/Return (secured

with hanger straps)

Storm Collar

Roof Flashing

3/4 in. (19 mm) to back &

sides of appliance

(except at nailing flanges

where it is 1/2 in. [13 mm])

Must have 2 in. (51 mm)

minimum clearance

to header

0 in.

to floor

2 in. (51 mm) min.

Shaded areas

represent

2 in. (51 mm) min.

air space clearance

required around pipe

Combustible Object

48 in.

1219 mm

Adapter attached here

(not shown)

Otros manuales para A36R

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Chimenea de interior de Heatilator

Heatilator

Heatilator Wood Burning Fireplace ST36D Manual de usuario

Heatilator

Heatilator CRAVE4836 Manual de usuario

Heatilator

Heatilator Maxus MAX60 Manual

Heatilator

Heatilator Wood Burning Fireplace EL36 Series Manual de usuario

Heatilator

Heatilator CNXT70PLUS Manual de usuario

Heatilator

Heatilator HR36 Manual de usuario

Heatilator

Heatilator HEIR36H-IFT Manual de usuario

Heatilator

Heatilator NA36AI Manual de usuario

Heatilator

Heatilator BIR36-B Manual de usuario

Heatilator

Heatilator LM42 Manual de usuario

Heatilator

Heatilator NDI30-C Manual de usuario

Heatilator

Heatilator CI80 Manual de usuario

Heatilator

Heatilator Wood Burning Fireplace EL42 Series Manual de usuario

Heatilator

Heatilator SCKVP-B Manual de usuario

Heatilator

Heatilator NB3630 Manual de usuario

Heatilator

Heatilator G136 Instrucciones de funcionamiento

Heatilator

Heatilator BIR42-B Manual de usuario

Heatilator

Heatilator NOVUS series Manual

Heatilator

Heatilator CNXT4236 Manual de usuario

Heatilator

Heatilator Birmingham BIR42 Manual de usuario

Heatilator

Heatilator G160 Manual

Heatilator

Heatilator Direct Vent Gas Appliance CD4236MR Manual de usuario

Heatilator

Heatilator NBV3630I Manual de usuario

Heatilator

Heatilator Direct Vent & B-Vent Gas Fireplace Caliber Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación