Heath Zenith 7308 Manual de usuario
V
O
L
U
M
E
TUNE–HOLD
1SECOND
SYNC–PRESS
ANDRELEASE
RESET–HOLD
10SECONDS
Wireless Chime
© 2018 HeathCo LLC 209670-01A
1. Remove orange battery tab from push button.
Remove back of case by pushing in tab on bottom
with a small screwdriver (see Figure 1). Remove
orange battery tab.
2. Install 3 alkaline“AA”batteries. Press in latch on
rear of chime and lift off battery cover (see Figure 2).
Install 3 alkaline “AA” batteries (not included) into
chime. Make sure batteries are installed according
to the diagram inside the chime (see Figure 3).
Replace battery access door onto back of chime.
3. Test range. Temporarily position chime and push
button where you want them mounted. Press push
button to verify chime and push button work prop-
erly. If chime does not sound, see Troubleshooting.
4. Adjust volume control to desired volume (see
Figure 2).
Figure 1
Figure 2
Figure 3
WARNING:To prevent possible SERIOUS
INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify
doctor.
This chime requires 3 “AA” alkaline batteries (not included). In typical use,
alkaline batteries will last up to one year.
This package includes (Style of push button and chime may vary from illustration):
Model
Wireless
chime Wireless push
button Hardware
pack
7308 ✔ ✔ ✔
Chime Volume Control
V
O
L
U
M
E
TUNE–HOLD
1SECOND
SYNC–PRESS
ANDRELEASE
RESET–HOLD
10SECONDS
Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
2
V
O
L
U
M
E
TUNE– HOLD
1SECOND
SYNC– PRESS
ANDRELEASE
RESET– HOLD
10SECONDS
5. Mount push button. Use either screws or double
sided tape to mount push button.
•
Screw Mounting: To mount with screws, remove
back of case by pushing in tab on bottom with a
small screwdriver (see Figure 1). Note: Remove
material in screw holes (if needed) before mounting
with screws. Attach back of case to door jamb or
wall (see Figure 4). Snap front of push button on.
• Tape Mounting: When attaching push button
using double sided tape, make sure the surface
of the door jamb or wall is clean.
6. Mount chime. Determine mounting location.
• Use template on back cover of manual for screw
placement. Mark two hole locations 1-13/16"
(46 mm) apart. Note: Make sure holes are level
before drilling.
• Drill two 7/32" (5.5 mm) diameter pilot holes for
wall anchors and insert anchors.
• Mount keyhole screws to wall leaving about 1/8"
(3 mm) of the screw threads exposed.
•
Using keyholes on back of chime base, hang base
on screws (see Figure 5).
Figure 5
Figure 4
Keyhole Slots
Keyhole Screw (x2)
3
Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
Inside Push Button
Tune Settings
The chime has different selectable tunes: Ding (one note tune) or a selectable musical
tune.This tune can be changed by following the instructions in the Tune Setting Table.
Note: All chime models are designed to work with up to 5 push buttons (sold
separately). All chimes are designed to play only two different tunes no matter how
many push buttons are used.
V
O
L
U
M
E
TUNE – HOLD
1 SECOND.
SYNC – HOLD
3 SECONDS.
RESET – HOLD
10 SECONDS.
Jumper Off Jumper On Back of Chime
Tune Setting Table
Push Button Chime Tune
Jumper - ON
(Back Door)
——— Ding
Jumper - OFF
(Front Door)
Press and release button on chime.
Listen for selected tune. Repeat to
select different tune.
Selected Musical
Tune
Tune Selection Guide
Front Door
Ding-Dong
Westminster
Whittington
Auld Lang Syne
Beethoven's Fifth
Relax
Back Door
Ding
A23
A23
Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
4
Troubleshooting
1. PROBLEM: Chime does not sound.
A. POSSIBLE CAUSE: Push button and chime are not synced.
A. CORRECTIVE ACTION: Sync the push button and chime.
• Press and hold the button on the chime until the chime sounds a “Beep-
Beep”.
• Press the push button within 30 seconds. The chime will sound a “Beep-
Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
B. POSSIBLE CAUSE: Batteries not installed correctly.
B. CORRECTIVE ACTION: Make sure batteries are installed according to the
diagram inside the push button and chime.
C. POSSIBLE CAUSE: Batteries are dead.
C. CORRECTIVE ACTION: Check charge of push button and chime batteries
and replace if necessary.
2. PROBLEM: Batteries seem okay, but the chime does not work after installation.
A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near metal
studs. Note: Metal reduces transmission range.
A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims to
move chime or push button away from metal surface.
B. POSSIBLE CAUSE: Chime is mounted near concrete floor or wall. Note:
Concrete may reduce range.
B. CORRECTIVE ACTION: Move chime away from concrete surface.
C. POSSIBLE CAUSE: Chime and push button are installed too far apart.
C. CORRECTIVE ACTION: Locate chime closer to push button.
5
Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
3. PROBLEM: Chime sounds when not intended (false triggers).
POSSIBLE CAUSE: Chime is receiving interference from another wireless
device.
CORRECTIVE ACTION: Reset chime and push button.
• Remove push button battery. Wait 30 seconds.
• Press and hold the push button for 10 to 15 seconds within 60 seconds
after installing battery into the push button.
• Press and hold the button on the chime until the chime sounds a “Beep-
Beep-Beep-Beep”.
• To re-sync the push button and chime, press and hold the button on the
chime until the chime sounds a “Beep-Beep”.
• Press the push button within 30 seconds. The chime will sound a “Beep-
Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
Note: The push button and chime come synced from the factory. The range of the
wireless chime can vary with location, temperature, and battery condition.
V
O
L
U
M
E
TUNE – HOLD
1 SECOND.
SYNC – HOLD
3 SECONDS.
RESET – HOLD
10 SECONDS.
V
O
L
U
M
E
TUNE – HOLD
1 SECOND.
SYNC – HOLD
3 SECONDS.
RESET – HOLD
10 SECONDS.
Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
6
Please contact us for assistance
before returning product to the
store or to HeathCo LLC.
If you experience a problem, follow this
guide.You may also contact us between
8:00 AM to 5:00 PM CST (M-F).
When contacting Technical Service,
please include the following informa-
tion: Name, Street Address, Daytime
Phone Number, Email Address, Model
Number, Date of Purchase, Place of
Purchase, Product Issue, and DATED
SALES RECEIPT FOR WARRANTY
REQUESTS.
Technical Service
No Service Parts Available for this
Product
HeathCo LLC
P.O. Box 90045
2445 Nashville Road
Bowling Green, KY 42101, USA
ATTN: Technical Service
Internet: www.hzsupport.com
Phone: 1-800-858-8501 (English Only)
Fax: 1-270-846-8500
7
Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
HeathCo LLC reserves the right to discontinue and to change specifications at any
time without notice without incurring any obligation to incorporate new features in
previously sold products.
ONE YEAR LIMITED WARRANTY
This is a “Limited Warranty” which gives you specific legal rights. You may
also have other rights which vary from state to state or province to province.
For a period of one year from the date of purchase, any malfunction caused by
factory defective parts or workmanship will be corrected at no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse,
abuse or negligence, light bulbs, batteries, and other expendable items are
not covered by this warranty. Any damage to the light fixture resulting from the
use of chemicals or a pressure washer machine are not covered by this war-
ranty. Unauthorized service or modification of the product or of any furnished
component will void this warranty in its entirety. This warranty does not include
reimbursement for inconvenience, installation, setup time, loss of use, unauthor-
ized service, or return shipping charges.
This warranty covers only HeathCo LLC assembled products and is not extended
to other equipment and components that a customer uses in conjunction with
our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION
OR CONDITION OF MERCHANT ABILITY OR THATTHE PRODUCTS ARE FIT
FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF
ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUS-
TOMER ANDTHERE SHALL BE NO LIABILITY ON THE PART OF HEATHCO
LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS
OR PROFITS,WHETHER OR NOT FORESEEABLE.Some states or provinces
do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
Please keep your dated sales receipt,it is required for all warranty requests.
Campana Inalámbrica
© 2018 HeathCo LLC 209670-01 S
1. Retire la pestaña naranja de la batería del botón
pulsador. Extraer la parte posterior de la caja pre-
sionando la aleta en el botón con un destornillador
pequeño (vea la Figura 1).Quite la aleta anaranjada
de la batería.
2.
Coloque las 3 pilas alkalinas “AA”.
Presione el
seguro en la parte de atrás de la campana y levante
la tapa de la pila (vea la Figura 2).Instale 3 baterías
alcalinas “AA” (no se incluyen) en la campanilla.
Asegúrese de que las baterías estén instaladas
según el diagrama del interior de la campanilla (vea
la Figura 3).Volver a colocar la puerta de acceso de
la batería sobre la parte posterior de la campanilla.
3. Pruebe el alcance. Ponga provisionalmente la
campana y el pulsador en la posición donde los
quiera instalar. Presione el pulsador para verificar
que la campana y el pulsador funcionen apropia-
damente. Si la campana no suena, vea Análisis de
Averías.
ADVERTENCIA: Para prevenir una posible
LESIÓN SERIA o LA MUERTE:
• NUNCA deje que los niños estén cerca de las
baterías.
• Si se traga una batería, notifique inmediata-
mente al doctor.
Esta campana requiere 3 pilas alcalinas tipo “AA” (no incluidas). Con un uso
normal, las pilas alcalinas durarán hasta 1 año.
Este paquete tiene (El estilo del pulsador y de la campana puede variar de la
ilustración):
Modelo
Campana
inalámbrica Pulsador
inalámbrico Paquete de
ferretería
7308 ✔ ✔ ✔
Figura 1
Figura 2
Figura 3
V
O
L
U
M
E
TUNE–HOLD
1SECOND
SYNC–PRESS
ANDRELEASE
RESET–HOLD
10SECONDS
Control del volumen
de la campana
V
O
L
U
M
E
TUNE–HOLD
1SECOND
SYNC–PRESS
ANDRELEASE
RESET–HOLD
10SECONDS
9
Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501
Figura 4
4.
Ajuste el control del volumen al volumen desea-
do (vea la Figura 2).
5. Instale el pulsador. Use ya sean tornillos o cinta
adhesiva por ambas caras para instalar el pulsador.
• Montaje con tornillos: Para montar con tornillos,
quite la parte de atrás de la caja empujando
hacia adentro la lengüeta de abajo con un
destornillador pequeño y girando la cuchilla
(vea la Figura 1). Nota: Quite la suciedad de los
orificios para tornillos (si es necesario) antes de
poner los tornillos. Coloque la parte de atrás de
la caja contra la jamba o la pared (vea la Figura
4). Encaje a presión la parte frontal del pulsador.
• Montaje con cinta adhesiva: Cuando fije el
pulsador usando cinta adhesiva por ambas caras,
asegúrese que la superficie de la pared o la del
batiente de la puerta estén limpias.
6. Monte la campana. Determine el sitio para el
montaje.
• Use la plantilla de la tapa posterior del manual
para marcar la posición de los tornillos. Marque
las posiciones de dos orificios separados por
46 mm (1-13/16 pulgadas) Nota: Asegúrese que
los orificios estén a nivel antes de taladrar.
• Taladre dos orificios guía de 5,5 mm (7/32 pul-
gadas) de diámetro para las anclas de pared e
inserte las anclas.
• Coloque en la pared los tornillos para los agujeros
piloto, dejando expuesta 3 mm (1/8 pulgada) de
la rosca del tornillo.
• En los agujeros piloto de la parte posterior de
la base de la campana, cuelgue la base en los
tornillos (vea la Figura 5).
Figura 5
V
O
L
U
M
E
TUNE– HOLD
1SECOND
SYNC– PRESS
ANDRELEASE
RESET– HOLD
10SECONDS
Agujeros de alineación
Tornillo para el agujero
de alineación (x2)
Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501
10
Programación del tono
La campanilla tiene diferentes melodías que se pueden seleccionar: Ding (melodía
de una nota) o una melodía musical para seleccionar.Esta melodía se puede cambiar
siguiendo las instrucciones de la Tabla de Programación de Melodías.
Nota: Todos los modelos de campanillas están diseñados para trabajar hasta con
5 botones pulsadores (se venden por separado). Todas las campanillas están
diseñadas para reproducir solo dos melodías diferentes, sin importar cuántos
botones pulsadores se utilicen.
V
O
L
U
M
E
TUNE – HOLD
1 SECOND.
SYNC – HOLD
3 SECONDS.
RESET – HOLD
10 SECONDS.
Dentro del Pulsador
Tabla de Programación de Melodías
Botón
pulsador
Campanilla Ajustes
Puente:
ENCENDIDO
(Puerta posterior)
———
Ding
Puente:
APAGADO
(Puerta principal)
Presione y suelte el botón de la campana.
Escuche el tono seleccionado. Repita
para seleccionar un tono diferente.
Melodía
musical
seleccionada
Parte de atrás de la
campana
Puente Apagado (Off) Puente Encendido (On)
Guía de Selección de Tonos
Puerta del frente
Ding-Dong Auld Lang Syne
Westminster Beethoven's Fifth
Whittington Relax
Puerta de atrás
Ding
A23
A23
Tabla de contenidos
Idiomas:
Otros manuales de Sistema de intercomunicación de Heath Zenith
