Heath Zenith Lighting Control Panel 598-1136-04 Manual de usuario

Lighting Control

Panel

Features

• Operational range of up to 100 feet.

• ControlsallHeath®/ZenithRFTechCommunica-

tions™ products.

• Adds programmable ON/OFF function for up to

16 lighting controls.

• UL/cUL listed power supply.

• FCC/IC tested and approved.

• 12/24 Hour Digital Clock Display.

• 9 volt battery backup to prevent program loss

due to power failure (9V battery not included).

• Flash control on compatible receivers when using the Panic feature.

Battery Installation and Battery Backup

The Lighting Control Panel is designed for 120VAC operation using the included

DC power converter, but has the added feature of an onboard battery backup

to prevent program memory loss. To install battery:

1. Remove battery cover on rear of

housing by sliding cover down.

2. Install 9 volt battery (not included)

according to polarity markings.

3. Close battery compartment by re-

versing the previous instructions.

Upon power failure, the battery backup

will automatically shut down all non-

essential functions. The display and

keypad will not work. The battery

backup will last in excess of 5 hours.

When power is restored, the unit will

restart the display and set all channels

to the OFF position. All programming

will be maintained unless the battery is

depleted. If the battery is depleted, reprogramming of the time and automated

functions will be required.

Note: If Lighting Control Panel will be disconnected from 120VAC power for

a prolonged period of time, disconnect 9V battery connector from battery to

prevent discharging of battery.

OFF

DIM

GROUP

MODE

ALL

OFF

PANIC

OFF

DIM

OFF

DIM

OFF

DIM

OFF

DIM

OFF

DIM

OFF

DIM

OFF

DIM

•

••

9V Battery

Battery

Cover

DC Power

Connector

9 Volt

Battery (Not

Included)

Battery Connector

Installing 9 Volt Battery and

DC Power Connector

It is recommended that the battery is replaced at least once a year.You might

want to choose a date that will be easy to remember (i.e.Birthday, Anniversary,

New Years, Daylight savings time changes, etc.).

2598-1136-04

PM A

A B

OFF

DIM

GROUP

MODE

ALL

OFF

PANIC

DIM

OFF

DIM DIM

OFF

DIM DIM

OFF

DIM DIM

– Select Time Set Program+

1 2

Product Identiﬁcation

Clock

Light Control - ON, OFF, DIM* with

indicator light.

Light Program Modes - Select Mode

1, 2, 1 & 2, or OFF (lights will indicate

which mode(s) are selected.

ALL ON - Turns all lights within a

GroupON.Selecteither GroupA

or B then press ALL ON.

Control Group - Select Group A or B

lighting controls.

PANIC* - All lights within a Group will ﬂash

ON and OFF. Select either Group A or B

then press PANIC.

TIME SET - Set the time and select

between 12-hour or 24-hour mode.

SELECT, (-, +) - Set hours and

minutesforclockandON/OFF

program setup.

AM, PM, 24 Hour

Clock Set - Lights

indicate AM or PM

setting. No light

indicates 24 Hour

setting.

ALL OFF - Turns all lights within a

Group OFF. Select either Group A or

B then press ALL OFF.

Control Group Indicator- Light on is

Group A, light off is Group B (Note:

also ﬂashes upon Program entry).

PROGRAM - Program ON/OFF times

for light controls (light is on when in

program mode).

Control Identiﬁcation -

Remove clear plastic ﬁlm

by placing two ﬁngers on

the plastic and“pinching”

theplastic.Remove card.

Usethedecals(included)

or write on the card to la-

beleachcontrol.Replace

card and plastic ﬁlm.

*DIM Control: Dims lighting controls that are equipped with the dimming feature.

Pressing DIM will toggle through the different dim levels. Each time the DIM

button is pressed, the control LED will momentarily light.

The receiver saves the last dim setting used.To recall the last dim setting, press

the DIM control once.

Note: Not all lighting controls have the DIM and PANIC (ﬂash) feature.

3598-1136-04

Setting The Time

PM A

A B

OFF

DIM

GROUP

MODE

ALL

OFF

PANIC

DIM

OFF

DIM DIM

OFF

DIM DIM

OFF

DIM DIM

– Select Time Set Program+

1 2

➊Press Time Set button. The hour numbers are highlighted.

PM A

A B

OFF

DIM

GROUP

MODE

ALL

OFF

PANIC

DIM

OFF

DIM DIM

OFF

DIM DIM

OFF

DIM DIM

– Select Time Set Program+

1 2

A B

OFF

DIM

OFF

DIM

GROUP

MODE

ALL

OFF

DIM

OFF

DIM DIM

OFF

DIM DIM

1 2

PM A

A B

OFF

DIM

GROUP

MODE

ALL

OFF

DIM

OFF

DIM DIM

OFF

DIM DIM

1 2

➋Press (+) and (-) buttons to the desired time.

➌Press Select button - Note minute numbers will highlight.

➍Press (+) and (-) buttons to the desired time.

➎Press Select button - The AM/PM/24-hour mode is now adjustable.

➏Press (+) and (-) buttons to toggle between 12-hour and 24-hour mode.

Note: The AM or PM indicator will light when the 12-hour mode is selected. If

neither AM nor PM indicator is lit, the 24-hour mode is selected.

➐If additional changes need to be made to the time, use the SELECT button

to scroll to the desired position.

➑Press TIME SET button when ﬁnished setting desired time.

Note: Pressing and holding the (+) or (-) buttons will scroll through the numbers

more rapidly.

4598-1136-04

PM A

A B

OFF

DIM

GROUP

MODE

ALL

OFF

PANIC

DIM

OFF

DIM DIM

OFF

DIM DIM

OFF

DIM DIM

– Select Time Set Program+

1 2

EXAMPLE 1 – Set Up Receivers

Following is one example of how the Lighting Control Panel can be programmed

to operate multiple light sources within a home.

The Control Panel has two “Groups” (A and B) with up to eight lighting controls

in each group. In this example, the eight controls within Group A will operate

the following light sources: Family Room (3), Kitchen, Front Porch, Back Porch,

Garage, and Foyer.

Light: Family Room Lamp #1 and #2

Receiver: Plug-In (1 per lamp)

Plug-In Code Setting:

1 2 3 4