HealthyAir HA-CMSC-G2-W-AEA Manual de usuario
Ceiling-Mount Aerosol Extractor
HA-CMSC-G2-W-AEA
Owner’s Manual
Table of Contents
HealthyAir® Series-1219-CM Filters
1
Important Safety Instructions
2
Technical Specifications
3
Packaging Reference
4-5
Component Reference
6-7
Installation Instructions
8-25
Electrical Wiring Instructions
26
Electrical Wiring Schematic
27
Operation Guidelines
28-29
Filter Replacement
30-34
Maintenance
35
Basic Service and Troubleshooting
36-40
1-Yeart Limited Warranty
41
Product Registration Form
42
Healthy Air Inc.
800-259-2535
www.HealthyAir.com
1
HealthyAir® Ceiling-Mount Aerosol Extractor
w/ Articulating Extraction Arm
HA-CMSC-G2-W-AEA
HA-SERIES-1219-CM
Replacement Filters
www.HealthyAir.com
2
WARNING
Cut power to the unit before servicing or replacing filters. Failure to
do so could result in serious personal injury and death.
I. Important Safety Instructions
Read the Owner's Manual and Important Safety Instructions carefully. Failure to
follow these instructions could cause a malfunction of the filter or unsatisfactory
performance. Follow a regular service and maintenance schedule for efficient
operation.
To reduce the risk of electric shock, fires, and/or injury:
• Do not use the air purifier in wet or damp locations
• Do not use outdoors
• Do not use at ambient temperature of above 95°F/35°C
• Do not use fabrics or other material to cover the inlet and outlet of the unit
• Do not allow children to operate or play with the unit
For safety reasons and to prevent electric shock, cut power to the unit under the
following conditions:
• When not in use for a long period of time
• When cleaning, servicing the machine or during replacement of filters
• When moving the air purifier
To prevent electric shock, do not dismantle, repair or modify this product.
Maintenance and cleaning instructions should be followed exactly as directed in
this manual. In case of malfunction, please contact an authorized distributor or
Healthy Air Inc. for service instructions.
To reduce the risk of electric shock, the unit has grounding type wiring that has a
third (grounding) wire. The unit must be hard wired, and all wiring must comply
with applicable electrical codes and ordinances. Do not alter the wiring.
3
II. Technical Specifications
Model Number
HA-CMSC-G2-AEA-W
Rated Voltage
120V/60HZ
Power Consumption
200W
Unit Weight
70 lbs.
Extraction Arm Weight
18 lbs.
Base Dimensions
24” (W) x 24” (L) x 15.4” (H)
Extraction Arm Dimensions
128” Extraction Arm (Fully Extended)
68” Vertical Section (Fixed)
63” Articulating Section (Adjustable)
Air Flow Rate
160 cfm
Sound Level
64 dB
4
III. Packaging Reference
The HealthyAir® Ceiling-Mount Aerosol Extractor, model HA-CMSC-G2-AE is
packaged in three (3) boxes as follows:
Note, in cases when multiple units are ordered, or customized orders are
placed, the secondary items may be packed in additional boxes.
Box 1:
(1) CMSC (Ceiling-Mount Source Capture) Unit
(1) Series-1219-CM Filter Set
(1) Inlet Port Cover-Plate
(2) Outside Vent Cover Plates
(1) Remote Control
(2) Batteries
(1) Manual Download Sheet
5
III. Packaging Reference
Box 2:
(1) Mounting Flange w/ 22” Pipe
(1) T-Outlet with 5” Pipe Stub
(1) 15” Pipe
(1) 3-Joint Articulating Extraction Arm Pipe
(1) Hood w/ Mounting Rings
(12) Screws
Box 3:
(1) Inlet Tube
(1) Flex Hose
(2) Hose Clamp
6
IV. Component Reference
CMSC Unit
12. Eyebolt
13. Capacitor
14. HV PCB
15. PCB Board
16. Wiring Box
17. Safety Switch
18. Fuse
19. Control Panel
20. Control Panel Display
21. Remote Control
22. Inlet Port Cover-Plate
23. Outlet Vent Cover-Plates
1. Thumb Screw
2. Faceplate
3. Pre-Filter
4. eGrid®
5. eHEPA® Filter
6. Activated Carbon Filter
7. Fan Coil
8. Blower/Motor
9. HV Contact Spring
10. Outside-Vent Outlet Port
11. Casing
7
IV. Component Reference
Articulating Extraction Arm
1. Mounting Base Flange w/ 22” Pipe
2. Airflow T-Outlet w/ 5” Pipe Stub
3. 15” Pipe Section
4. 3-Joint Articulating Arm
5. Hood
6. 360° Swivel Ring
7. Locking Knob
8. Airflow Control Valve
9. Handle
10. Flex Hose w/ (2) Hose Clamps
8
V. Installation Instructions
5.1 Install Eyebolts
5.1.1 Carefully place the CMSC unit face down, as shown in Fig. 1.
5.1.2 Screw the four (4) Eyebolts into the respective rivet nuts, located at the
four corners of the Casing.
5.1.3 Ensure that each Eyebolt is fully and securely installed.
Fig. (1) – Installing Eyebolts
Eyebolts
Faceplate
Casing
CMSC Unit
9
V. Installation Instructions
5.2 Locating Unit
For optimal performance, the HealthyAir® Ceiling-Mount Aerosol Extractor
should be located such that the Hood of the Extraction Arm can be strategically
positioned about 6”-12” from the emission source.
The unit base should also be installed where it can be easily accessed and
opened for periodic filter replacement. Refer to Section 9.2 for filter
replacement details.
5.2.1 The base unit is designed to be installed in place of a standard 2'x2’
ceiling tile, and it must be securely attached to the building structure for
adequate support.
5.2.2 Depending on the type of building structure, and whether the ceiling has
I-Beam or concrete construction, follow the appropriate protocol for
proper installation and support of the unit.
5.3 Locating Extraction Arm
The Articulating Extraction Arm is specifically designed to work with the
HealthyAirâ Ceiling-Mount Source Captureâ unit model HA-CMSC-G2.
Together, this system will enable effective capture and filtration of ultra-fine
airborne aerosols generated in various procedures.
The Articulating Extraction Arm is to be installed to the main structure in the
ceiling (above the drop ceilings) on either side of the chair or work area. The
exact and optimal location of the arm depends on the specific layout of the site
and the presence of other equipment.
In general, the Articulating Extraction Arm should be located within a radius of
36” from the area where work is performed. The arm is equipped with (3)
adjustable joints and a 360° swivel ring, that enable it to be maneuvered to
position the capture hood within 6” of the breathing zone.
The Ceiling-Mount Source Captureâ unit is to be located 4-6’ from the
Articulating Extraction Arm and connected to the arm via a Flex Hose.
Tabla de contenidos
