HealthyAir HA-SCP-G5 Manual de usuario
HealthyAir® Source Capture System®
Air Purification & Local Exhaust
Ventilation System
Models: HA-SCP-G4/G5/G6
Healthy Air Inc.
The Source For Source Capture®
800-259-2535
www.HealthyAir.com
HealthyAir® HA-IFM-1111 Filter
Important Safety Instructions
Technical Characteristics
Packaging Reference
Packing Notice
Component Reference
Assembly Instructions
Operation Guidelines
Filter Replacement
Maintenance
Basic Service and Troubleshooting
Electrical Wiring Schematic
1-Yeart Limited Warranty Product
Registration Form
1
2
3
4
5
6
7-12
13-14
15-17
18
19-23
24
25
26
Healthy Air Inc.
The Source For Source Capture®
800-259-2535
www.HealthyAir.com
HealthyAir® Source Capture System®
Models: HA-SCP-G4/G5/G6
Table of Contents
2
WARNING
Unplug the power cord before servicing or replacing filters. Failure
to do so could result in serious personal injury and death.
I. Important Safety Instructions
Read the Owner's Manual and Important Safety Instructions carefully. Failure to
follow these instructions could cause a malfunction of the filter or unsatisfactory
performance. Follow a regular service and maintenance schedule for efficient
operation.
To reduce the risk of electric shock, fires, and/or injury:
Do not use the air purifier in wet or damp locations
Do not use outdoors
Do not use at ambient temperature of above 95°F/35°C
Do not use fabrics or other material to cover the inlet and outlet of the unit
Do not allow children to operate or play with the unit
For safety reasons and to prevent electric shock, unplug the power cord from the
electric outlet socket under the following conditions:
When not in use for a long period of time
When cleaning, servicing the machine or during replacement of filters
When moving the air purifier
To prevent electric shock, do not dismantle, repair or modify this product.
Maintenance and cleaning instructions should be followed exactly as directed in
this manual. In case of malfunction, please contact an authorized distributor or
Healthy Air Inc. for service instructions.
To reduce the risk of electric shock, the equipment has a grounding type plug that
has a third (grounding) pin. This plug will only fit into a grounding type power
outlet. If the plug does not fit into the outlet, contact qualified personnel to install
the proper outlet. Do not alter the plug in any way.
To reduce the risk of electric shock, do not pull the cord to remove the plug from
its outlets. Protect the cord against heat, oil and sharp objects. Do not run any
appliance over the cord. Do not pull or carry by the cord, use cord as a handle,
close a door on the cord, or pull cord around sharp edges or corners.
3
II. Technical Characteristics
Visit www.HealthyAir.com and select Specifications from the menu bar to
download detailed Specification Sheet, with complete product dimensions and
air flow rate information.
Model Numbers
HA-SCP-G4/G5/G6
(Note letters following Generation "GX"
specify color & options)
Rated Voltage
120V/60HZ
Power/Amperage 280W/2.75A
Weight
40 lbs.
Base Dimensions
14x12x24 in.
Flex Hose Length
(Standard)
4'L
(Note custom length available)
Download Specifications Sheet from
Specifications page at www.HealthyAir.com
4
III. Packaging Reference
The Source Capture® Air Purification System is shipped in two (2) cartons, as
follows:
Carton 1: (1) Source Capture® Air Purification Unit w/ (1) Integrated Filter
Module, (4) Wheel Casters, (1) Acoustic Mat, (1) Remote
Control, (1) Power Cord, (1) Screwdriver, (1) Manual
Carton 2: (1/2) Flex Hose + Hood, (1/2) Hose Clamp, (1/2) Grill + LED Cable
+ LED Bulb (Optional), (1) Outside Vent Adapter Kit – Outlet Flange
+ Base Blank-Off Plate (Optional)
5
IV. Packaging Notice
NOTICE
Before operating the machine, do the following:
1. Open the Access Door (Refer to Section 8.2)
2. Remove the Integrated Filter Module (HA-IFM-1111)
3. Remove the plastic wrapping from the filter!
4. Re-install the Integrated Filter Module
5. Replace and secure the Access Door
Remove plastic wrapping
from Integrated Filter
Module prior to use!
6
V. Component Reference
1. Outer Frame
2. Acoustic Mat
3. Blower/Motor
4. Metal Screen
5. Caster Wheels
6. Base Plate
7. Motor Mount Plate
8. Baffle Plate
9. Air Inlet Guide
10. Integrated Filter Module
11. Activated Carbon Filter
12.eHEPA® Filter
13. eGrid
14.Silicon Seal
15.Pre-Filter
16. HV PCB
17.Switch
18. Capacitor
19. PCB
20. Flex Hose
21.LED
22. Hood
23. G4 Bulb Mount
(Optional)
24. LED Grill (Optional)
25. LED Cable Plug (Optional)
26. LED Cable Socket
27. Inlet Tube
28. Control Panel Display
29. Control Panel
30. Plastic Screw
31. HV Contact Spring
32. Power Cord
33. Remote Control
34. Base Blank-Off Plate
(Optional)
35. Outlet Flange (Optional)
7
VI. Assembly Instructions
6.1 Install Caster Wheels
The following procedure is for Recirculating Ventilation use of the unit, whereby
purified air is vented through the Base Plate and reintroduced into the facility.
For Outside Ventilation application, in which purified air is vented out of the
facility, skip Section 6.1 and refer to installation instructions in Section 6.4.
6.1.1 Place the unit on its side on a flat surface, as shown in Fig. 1.
6.1.2 Locate the four (4) Caster Wheels and the Screwdriver that are
provided in Carton 1.
6.1.3 Unscrew and remove the screws that are pre-mounted onto the Base
Plate, on the bottom of the unit. There are four (4) screws per wheel,
for a total of sixteen (16) screws.
6.1.4 Align the holes of the Caster Wheel Mount with the holes on the Base
Plate and use four (4) screws to securely mount each Caster Wheel to
the Base Plate one by one.
Fig. (1) – Caster Wheel Installation
Base Plate
(16) Screws for
mounting wheels
8
VI. Assembly Instructions
6.2 Install LED Lighting (Optional)
Note that, the LED Lighting system is an optional feature. To add this feature, visit
www.HealthyAir.com and select LED Lighting from the Spare Parts tab in the
menu.
If LED Lighting was not purchased, skip section and proceed to Section 6.3.
6.2.1 Mount the LED Light Bulb on the Grill, by inserting the lip of the bulb into
the 4-piece cylinder located in the center of the Grill.
6.2.2 Connect the LED Cable to the LED Light Bulb, by sliding the two (2)
prongs of the bulb into the G4 Bulb Mount.
6.2.3 Pass the 52” LED Cable through the Hood and entire length of the Flex
Hose, such that the LED Cable Plug passes through the bottom of the
Flex Hose.
6.2.4 Connect the Grill to the Hood by snapping the Grill onto the rim of the
Hood, as shown in Fig. 2.
6.2.5 Connect the LED Cable Plug to the LED Cable Socket of the LED Cable
that is fixed to the edge of the Inlet Port.
Fig. (2) – LED Lighting Installation
Grill
LED
Bulb
LED Cable w/
Bulb Mount
LED Cable
Plug
LED Cable
Socket
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Admirador de HealthyAir
