HDanywhere MHUB Manual de usuario
1x MHUB MAX (4X4) CHASSIS
1x IEC POWER CABLE
A
B
C
D
1x MASTER REMOTE
2x CHASSIS MOUNTING WINGS INFRARED (IR) CABLE
1x IR RX
1Connect a HDMI source device (e.g Satellite/Cable TV, Apple TV, Blu-ray, DVD
etc) to one of the ports labelled “SOURCE INPUT” on the MHUB chassis using a
good quality HDMI cable. The MHUB can support HDMI content up to 18Gbps.
The steps below describe how to connect a single HDMI source to a display location for outputs A-D and enable remote control (IR) of the MHUB. Repeat the steps below as
necessary for each source or display
2Connect a HDMI display to one of the “DISPLAY” ports labelled A-D using a
good quality HDMI cable. Ensure that your display is switched to the correct
input.
3Power on the Matrix by connecting the included IEC Power Cable to the AC
input.
4
5
Connect the IR RX cable to the port labelled “HUB IR (IN)” Test that control of
the matrix is working using the included Master Remote.
To complete the installation, connect the MHUB “HUB CONTROL IP” port to
your router via an ethernet cable.
HDMI CABLE
INFRARED (IR) CABLE
NETWORK CABLE
POWER
2
3 5
1
4
OK
MAX
MHUB
IN THE BOX
QUICK START GUIDE
FULL MANUAL ON SUPPORT.HDANYWHERE.COM
MHUB MAX (4X4) TOUCH PANEL (FRONT)
MHUB MAX (4X4) (BACK)
“HUB CONTROL IP” Port: Connect the MHUB
system to your router via this port to enable
MHUB-OS features and IP control from the uControl
App
“HUB CONTROL RS232” Port: Use to integrate your
MHUB with a control system via RS232
“SOURCE INPUTS” [1-4]: Use to connect HDMI
source devices to the MHUB
“DISPLAY OUTPUTS” [A-D]: Use to connect HDMI
displays
“DIGITAL” AUDIO PORT: Use this port to extract
multi-channel audio via a coaxial cable
“STEREO” AUDIO PORT: Use this port to extract
down-mixed stereo audio via a 3.5mm jack cable
“HUB IR (IN)”: Connect an IR RX to this port to
control your MHUB with the included IR remote
control (or other learning remote) whilst in
line-of-sight of the IR RX. Or control the MHUB with
a third party controller via direct IR, using the
optional add-on accessory called the ‘MHUB IR
integration cable’. (1.55.911.001.1)
AC INPUT: Connect the supplied IEC lead to this
port to provide power to your matrix
MHUB ON/OFF: Press and hold for 2 seconds to
turn MHUB on or off
SOURCE SELECTOR (1-4): Select which source you
want to switch to
LCD PANEL: Displays MHUB system information
and switching status
DISPLAY SELECTOR (A-D): Select which display
you want to ouput to
MENU AND NAVIGATION CONTROL: Brings up
EDID and IP menu settings
MHUB MAX (4X4) CHASSIS (REAR ) MHUB MAX (4X4) TOUCH PANEL (FRONT)
IP
RS232
HUB CONTROL 1 2 3 4 AB C D
SOURCE INPUT
DISPLAY
hub ir (IN)
100-240V AC 50/60HZ
DIGITAL STEREO DIGITAL STEREO DIGITAL STEREO DIGITAL STEREO
OK
MAX
MHUB
MAX
MHUB
1 2 3 4
1 2 34
65
5
7 8
1
2
3
4
5
6 1
2
3
4
5
7
8
PORTS & LABELS
FULL MANUAL ON HDANYWHERE.COM/SUPPORT
Otros manuales para MHUB
4
Otros manuales de Chasis de HDanywhere
