HBM K800 Manual de usuario
Operating Manual | Bedienungsanleitung
English Deutsch
K800
Calibration Unit
Kalibriergerät
Hottinger Baldwin Messtechnik GmbH
Im Tiefen See 45
D-64293 Darmstadt
Tel. +49 6151 803-0
Fax +49 6151 803-9100
www.hbm.com
Mat.: 7-0102.0012
DVS: A01098_05_X00_00 HBM: public
07.2020
EHottinger Baldwin Messtechnik GmbH.
Subject to modifications.
All product descriptions are for general information only.
They are not to be understood as a guarantee of quality or
durability.
Änderungen vorbehalten.
Alle Angaben beschreiben unsere Produkte in allgemeiner
Form. Sie stellen keine Beschaffenheits- oder Haltbarkeits
garantie dar.
Operating Manual | Bedienungsanleitung
English Deutsch
K800
Calibration Unit
Kalibriergerät
2A01098_05_X00_00 HBM: public K800
English
1 Safety instructions 3........................................
2 Symbols used 7............................................
2.1 Symbols used in this manual 7................................
2.2 Symbols on the device 7......................................
3 Scope of supply 8..........................................
3.1 Option (not included in the scope of supply) 8...................
4 Field of application 9.......................................
5 Principle 10.................................................
6 Operation 12................................................
6.1 Connections 12...............................................
6.1.1 Connector elements on back of device 12........................
6.1.2 Pin assignment 13............................................
6.2 Digital controller 15...........................................
6.3 Device front panel 17..........................................
7 Calibrating a measuring amplifier 18..........................
Safety instructions
K800 A01098_05_X00_00 HBM: public 3
1 Safety instructions
Appropriate use
The K800 calibration unit must only be used to calibrate strain‐gauge bridge
measuring amplifiers. Use for any purpose other than the above shall be
deemed to be inappropriate. In the interests of safety, the device should only
be operated as described in the Operating Manuals. It is also essential to
comply with the legal and safety requirements for the application concerned
during use. The same applies to the use of accessories.
Each time, before starting up the equipment, you must first run a project
planning and risk analysis that takes into account all the safety aspects of
automation technology. This particularly concerns personal and machine
protection.
Additional safety precautions must be taken in plants where malfunctions could
cause major damage, loss of data or even personal injury. In the event of a
fault, these precautions establish safe operating conditions.
This can be done, for example, by mechanical interlocking, error signaling, limit
value switches, etc.
General dangers of failing to follow the safety instructions
The K800 is a state of the art unit and as such is reliable. The module may
give rise to dangers if it is inappropriately installed and operated by untrained
personnel.
Any person instructed to carry out installation, starting up, maintenance or
repair of the module must have read and understood the Operating Manual
and in particular the technical safety instructions.
Conditions on site
SProtect the device from direct contact with water.
SProtect the K800 from moisture and humidity or weather conditions such as
rain, snow.
SDo not expose the device to direct sunlight.
Safety instructions
4A01098_05_X00_00 HBM: public K800
SPlease observe the permissible maximum ambient temperatures and
humidity stated in the specifications.
SInstall the device so that it can be disconnected from the supply voltage at
any time without difficulty.
SIt is safe to operate the K800 up to a height of 2000 m.
Maintenance and cleaning
The K800 is maintenance-free.
SBefore cleaning, disconnect all connections.
SClean the housing with a soft, slightly damp (not wet!) cloth. You should
never use solvents, since these could damage the labeling.
SWhen cleaning, ensure that no liquid gets into the module or connections.
Residual dangers
The scope of supply and performance of the K800 only covers a small area of
measurement technology. In addition, equipment planners, installers and
operators should plan, implement and respond to the safety engineering
considerations of measurement technology in such a way as to minimize
remaining dangers. On-site regulations must be complied with at all times.
There must be reference to the remaining dangers connected with
measurement technology.
Product liability
In the following cases, the protection provided for the device may be adversely
affected. Liability for device functionality then passes to the operator:
SThe device is not used in accordance with the operating manual.
SThe device is used outside the field of application described in this Chapter.
SThe operator makes unauthorized changes to the device.
Safety instructions
K800 A01098_05_X00_00 HBM: public 5
Working safely
Notice
The device must not be directly connected to the DC voltage supply system.
Supply voltage 10 V … 15 V (DC).
The supply connection, as well as the signal and sense leads, must be
installed in such a way that electromagnetic interference does not adversely
affect module functionality (HBM recommendation: "Greenline shielding
design", downloadable from the Internet at http://www.hbm.com/Greenline).
Automation equipment and devices must be installed in such a way that
adequate protection or locking against unintentional actuation is provided (e.g.
access checks, password protection, etc.).
When devices are working in a network, these networks must be designed in
such a way that malfunctions in individual nodes can be detected and shut
down.
Safety precautions must be taken both in terms of hardware and software, so
that a line break or other interruptions to signal transmission, such as via the
bus interfaces, do not cause undefined states or loss of data in the automation
device.
Conversions and modifications
The device must not be modified from the design or safety engineering point of
view except with our express agreement. Any modification shall exclude all
liability on our part for any damage resulting therefrom.
In particular, any repair or soldering work on motherboards is prohibited. When
exchanging complete modules, use only original parts from HBM. The product
is delivered from the factory with a fixed hardware and software configuration.
Changes can only be made within the possibilities documented in the operating
manual.
Safety instructions
6A01098_05_X00_00 HBM: public K800
Qualified personnel
Qualified personnel means persons entrusted with the installation, assembly,
commissioning and operation of the product, who possess the appropriate
qualifications for their function.
This includes people who meet at least one of the three following requirements:
SKnowledge of the safety concepts of automation technology is a require
ment and, as project personnel, you must be familiar with these concepts.
SAs automation plant operating personnel, you have been instructed how to
handle the machinery. You are familiar with the operation of the equipment
and technologies described in this documentation.
SAs commissioning engineers or service engineers, you have successfully
completed the training to qualify you to repair the automation systems. You
are also authorized to activate, ground and label circuits and equipment in
accordance with safety engineering standards.
It is also essential to comply with the legal and safety requirements for the
application concerned during use. The same applies to the use of accessories.
The K800 must only be installed by qualified personnel, strictly in accordance
with the specifications and with the safety requirements and regulations listed
below.
Maintenance and repair work on an open device with the power on may only
be carried out by trained personnel who are aware of the dangers involved.
Symbols used
K800 A01098_05_X00_00 HBM: public 7
2 Symbols used
2.1 Symbols used in this manual
Important instructions for your safety are specifically identified. It is essential to
follow these instructions in order to prevent accidents and damage to property.
Symbol Meaning
Notice This marking draws your attention to a situation in
which failure to comply with safety requirements can
lead to damage to property.
Important
Important information
This draws your attention to important information
about the product or about handling the product.
2.2 Symbols on the device
Symbol Meaning
Statutory waste disposal mark
In accordance with national and local environmental
protection and material recovery and recycling regulations, old
modules that can no longer be used must be disposed of
separately and not with normal household garbage.
Statutory mark of compliance with emission limits in electronic
equipment supplied to China
CE mark
The CE mark is used by the manufacturer to declare that the
product complies with the requirements of the relevant EC
directives (the Declaration of Conformity can be found at
http://www.hbmdoc.com/en/industrial-amplifiers/
Scope of supply
8A01098_05_X00_00 HBM: public K800
3 Scope of supply
SCalibration unit K800 120 ohms
or K800 350 ohms
or K800 700 ohms
or K800 1000 ohms
S2 Connection cables, 3 m long, 25‐wire Order no.: 1-KAB263-3
SUSB‐ connection cable, 2 m long
SUSB power supply (Europlug)
SUSB power supply (NEMA-1)
SCD with driver software
SOperating Manual
3.1 Option (not included in the scope of supply)
DKD calibration certificate K-CAL-SD5
Tabla de contenidos
Idiomas:
Otros manuales de Equipo de prueba de HBM
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
