Hazro HZ27WB Manual de usuario
Copyright © 2011 by Hazro Technologies. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored
in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of Hazro Technologies.
Disclaimer
Hazro Technologies makes no representations or warranties, either expressed or implied, with respect to the contents hereof and speci-
cally disclaims any warranties, merchantability or tness for any particular purpose. Further, Hazro Technologies reserves the right to revise
this publication and to make changes from time to time in the contents hereof without obligation of Hazro Technologies to notify any person
of such revision or changes.
ENGLISH
27” / 30” LCD Monitor
WQHD/WQXGA IPS LCD
HZ27WB, HZ30Wi/Q
User Manual
DISCLAIMER
UNDER NO CIRCUMSTANCES SHALL HAZRO BE LIABLE TO THE
ORIGINAL PURCHASER AT RETAIL OR ANY OTHER PERSON FOR ANY
INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES, WHETHER
ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT,
OR OTHERWISE.
The warranty, disclaimer, and remedies set forth in this document are
exclusive and replace all others, oral or written, expressed or implied. No
Hazro dealer, agent, or employee is authorized to make any modication,
extension, or addition to this warranty. The information contained herein is
subject to change without notice.
Avoid placing the monitor in
direct sunlight or near heating
appliances such as radiators
or gas res etc. Doing so may
result in panel non-uniformity
and random appearance of black
spots on the surface of the panel.
Ensure monitor is placed on
a stable surface or is xed
permanently. Vibration or
shock to the monitor can cause
permanent damage to the
product and can result in injury.
Contact Hazro or your reseller
immediately if you notice smoke
or a strange burning smell. Do
not use the monitor unless given
specic instructions by Hazro to
do so or by a qualied electrician.
Avoid connecting multiple electric
appli-ances to a single wall outlet
as this may result in re due to
overheating of the wall outlet.
CAUTION
THE FOLLOWING GUIDELINES ARE IN PLACE FOR YOUR SAFETY.
PLEASE REFER TO THESE BEFORE SETTING UP THE MONITOR.
NEVER OPEN THE MONITOR. There are no user serviceable parts inside and opening or ▪
removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to ▪
qualied service personnel. Warranty becomes void if the monitor is opened.
Do not spill any liquids into the cabinet or use your monitor near water.▪
Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points,▪
which can be harmful or fatal or may cause electric shock, re or equipment failure.
Do not place any heavy objects on the power cord. Damage to the cord may cause shock or re. ▪
The inside of the uorescent tube located within the TFT monitor contains mercury. ▪
Please follow the bylaws or rules of your municipality to dispose of the tube properly. ▪
Do not bend power cord.▪
Do not use monitor in high temperature, humid, dusty, or oily areas.▪
Do not cover the vents on monitor.▪
Do not install where the monitor will be exposed to continual vibration.▪
If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.▪
Immediately unplug your monitor from the wall outlet and refer servicing to qualied service personnel
under the following conditions:
When the power supply cord or plug is damaged. ▪
If liquid has been spilLCD, or objects have fallen into the monitor. ▪
If the monitor has been exposed to rain or water. ▪
If the monitor has been dropped or the cabinet damaged. ▪
If the monitor does not operate normally by following operating instructions. ▪
PLEASE NOTE THAT ALL HAZRO Monitor ARE STRICTLY FOR INDOOR USE ONLY
Allow adequate ventilation around the monitor so that heat can properly dissipate.
Do not put anything on top of monitor. The power cable connector is the primary means of detaching the
system from the power supply. The monitor should be instalLCD close to a power outlet which is easily
accessible. Handle with care when transporting. Save packaging for transporting.
Safety Precautions and Maintenance
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
USE THE POWER SUPPLY CORD AND DVI CABLE SUPPLIED WITH THIS EQUIPMENT SO AS
TO KEEP INTERFERENCE WITHIN THE LIMITS OF AN FCC CLASS B EN55022 DEVICE.
CAUTION
DO NOT USE THIS UNIT’S POLARISED PLUG WITH AN EXTENSION CORD, RECEPTACLE OR
OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED.
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED
FROM THE AC OUTLET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE
DISCONNECT THE POWER CORD FROM THE AC OUTLET.
THE ATTACHED POWER CORDS ARE TO BE USED EXCLUSIVELY FOR THIS PRODUCT. NEVER
USE THEM FOR OTHER PRODUCTS.
This symbol warns the user that un-insulated voltage within the unit may have sufcient
magnitude to cause electric shock. Therefore, it is dangerous to make any kind of
contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and
maintenance of this unit has been included. Therefore, it should be read carefully in
order to avoid any problems.
WEEE Directive
Waste Electrical and Electronic Equipment
Your Hazro product is designed and manufactured with high quality materials and components which
can be recycled and re-used. In the European Union, the label above indicates that this product
should not be disposed of with household waste. It should be deposited at an appropriate facility to
enable recovery and recycling. In the EU, there are separate collection systems for used electrical and
electronic products. For information on how to recycle this product, please contact your local council or
environmental agency.
Maintenance and Care
Ensure the monitor is switched off from the mains for a minimum of 30 minutes before attempting to
clean the LCD panel. Simply switching off the monitor from the OSD menu is not recommended and
should be avoided.
To avoid material or screen coating degradation, observe the following precautions.
To remove dust from the screen surface/cabinet, wipe gently with a soft cloth. If dust is persistent, ▪
wipe with a soft cloth slightly moistened with a diluted mild detergent solution.
Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such▪
as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact
with rubber or vinyl materials may result in damage to the glass protection, screen surface and
cabinet material.
Periodic vacuuming of the ventilation openings is recommended to ensure to proper ventilation.▪
When adjusting the angle of the monitor, move it slowly so as to prevent the monitor set from ▪
moving or slipping off from its table stand.
Image Persistence
Image persistence is when a residual or “ghost” image of a previous image remains visible on the
screen. Unlike CRT monitors, image persistence on LCD displays is not permanent [although constant
images being displayed for a long period of time should be avoided]. To remedy image persistence, turn
off the monitor for as long as the previous image was displayed. For example, if a static picture was
displayed for one hour and a residual image remains, the monitor should be turned off for one hour to
erase the image.
NOTE: As with all personal display devices, Hazro recommends using a moving screen saver at regular
intervals whenever the screen is idle or turning off the monitor when not in use.
Recommended Use
Prior to installation, please ensure that the graphics card on your computer is set to the native resolution
of the monitor (2560x1440 or 2560x1600 depending on the Hazro LCD model). Be aware that not all
graphics cards provide this resolution. If this is the case, check the graphics card manufacturer’s website
for an updated driver. Software video drivers are often updated and are made available for new hardware
video resolutions. However, if no software update is available, you may need to replace and update the
graphics card in order to support the native resolution of the monitor. If you select a resolution other than
the native one, be aware that this causes interpolation which results in the image becoming blurred and
irregular in size. It is preferable to adjust the image position, resolution and frequency via the graphics
card software utility. Please ensure that all adjustments are made after a warm-up period of at least 30
minutes.
Available Temperature & Humidity
Operating Temperature: 0 ~ 35°C Storage Temperature: -10 ~ 50°C
Operating Humidity: 10 ~ 90 % RH Storage Humidity: 40 ~ 70 % RH
For dot defect [dead pixel] of TFT
Hazro LCD monitors are manufactured using high-end semiconductor technology with precision ratings
of 99.9% and above. However, it may be the case that certain RGB and white pixels seem darker (or
entirely unlit i.e. black). Should such a situation occur, please refer to the warranty section in this manual
for further details.
PC system requirements
Adjust the computer resolution and screen refresh rate in the control panel of PC as described below to
obtain the best picture quality:
Resolution : 2560 x 1440 Refresh rate: 60 Hz
Resolution : 2560 x 1600 Refresh rate: 60 Hz
The HZ27WB and HZ30Wi/Q displays require a graphics card which features a Dual-Link
DVI output [DVI-D]. This term is not to be confused with graphics cards that have two DVI
connectors as it is possible that neither outputs would be Dual Link compatible. It is usual for
twin DVI output graphics cards to have one connector which is Dual Link compatible [DVI-D] and the
other to be single link [DVI]. Never use a Single Link DVI cable on a Dual-Link DVI device.
Macintosh system requirements
Please ensure that any embedded graphics controller is Dual Link compatible and it can support
resolutions up to 2560x1600 or 2560x1440. NOTE: Some resolutions e.g. 1920x1154 will not be
interpolated and cannot be mapped on Hazro monitors. Forcibly manipulating the monitor EDID values
will void all warranties.
Ergonomic Suggestions
Hazro LCD monitors are designed and optimised for use indoors. The correct combination of resolution,
brightness and ergonomics will ensure minimal eye strain and other symptoms associated with
prolonged viewing of a LCD monitor. However, to further protect against these symptoms, do not operate
the monitor against a bright background in a dark room. For optimal viewing comfort, the monitor should
be set just below eye level and 45-70 cm (18-28 inches) away from your eyes.
When using the monitor over a prolonged time period, a ten minute break every hour is recommended.
Other Suggestions
- Shoulders relaxed
- Forearms and hands in a straight line
- Forearms level or tilted up slightly
- Lower back supported
- Top of screen at or slightly below eye level
- Thighs horizontal
- Screen positioned to avoid reective glare
- Feet at on oor
Table of Contents:
Chapter 1. Getting Started Page
Product parts 1
Monitor I/O Ports 1
Preset Display Modes 2
OSD Button Control 2
Monitor Connection 2
Chapter 2. Specications
Specications 3
Chapter 3: Frequently Asked Questions
FAQs 4
Chapter 4: Warranty
What the warranty covers 7
What the warranty does NOT cover 7
Warranty types 8
How Long The Warranty is Effective 8
Who the Warranty Protects 8
Filing a Warranty Claim 8
Miscellaneous Issues 9
Pixel defect policy 11
Dual LInk DVI Cable AC Power Cord
USB A-to-B Cable *
Instruction Manual
Consider keeping the packaging in storage
for use in the future when you may need to
transport the monitor. The tted foam
packing is ideal for protecting the monitor
during transport. Hazro offer replacement
packaging for a small fee.
* Available on some models only.
Chapter 1. Getting Started
This User’s Guide contains detailed information on the Hazro HZ27WB, HZ30Wi & HZ30Wi-Q LCD
monitors.
Please make sure the following items are included with your monitor. If any items are missing or
damaged, contact your dealer or place of purchase.
Product Parts
Chapter 1 : Getting Started
LCD Monitor
24V DC Adapter *
Monitor I/O Ports
DC Connector:
Some models only
Dual Link DVI Connector IEC AC Inlet USB ‘B’ Type - Some
models only
V - V +
Monitor Connections
Power Input [DC 24V] - not available on all models1.
Dual-Link DVI Connector2.
IEC AC Inlet - not available on all models3.
USB ‘B’ type connector - not available on all models4.
Page 1
Chapter 1 : Getting Started
Chapter 1 : Getting Started
Preset Display Modes
The Hazro HZ27WB and HZ30Wi/Q can detect all VESA standard graphic resolutions shown in the
table below. Note that no other resolution apart from the native i.e. WQHD [2560x1440] and WQXGA
[2560x1600] will be mapped. All other resolutions will result in interpolation i.e. blown out to ll the
screen:
2560 X 1600 @ 60Hz
2560 X 1440 @ 60Hz
1920 X 1200 @ 60Hz
1920 X 1080 @ 60Hz
1600 X 1200 @ 60Hz
1280 X 1024 @ 60Hz
1280 X 800 @ 60Hz
1280 X 768 @ 60Hz
1024 X 768 @ 60Hz
800 X 600 @ 60Hz
640 X 480 @ 60Hz
OSD Button Control
The OSD Buttons can be found along the side
face of the monitor [either left or right].
UP: Brightness Adjustment [increase]
DOWN: Brightness Adjustment [decrease]
POWER: Power On / Off
Monitor Connection
To connect the monitor to the computer, please follow the instructions given below:
Connect DVI cable to the computer. Tighten all the screws. •
Connect DVI cable to the bottom of monitor. Tighten the screws. •
Connect the ‘B’ type end of the USB cable to the monitor and other end to computer. [if applicable]•
Switch on monitor via switch found on the side of the monitor.•
Switch on computer and if no signal is detected, power on the monitor via the OSD buttons found on •
the side face of the monitor.
USB type A ~ type B
USB is not available on all models
OSD Buttons
Page 2
Model HZ30Wi HZ30Wi-Q HZ27WB
Panel 30” WQXGA S-IPS 27” WQHD S-IPS
Panel Type 8bits 16.7Million Colors 10 bits [1.07Billion colors A-FRC]
Size 30” Diagonal 29.7inch (WQXGA),
64.13 x 40.1 cm visible area
27” Diagonal 68.47cm (WQHD),
59.67 x 35.57cm visible area
Resolution 2,560(H) X 1,600(V) 2,560(H) X 1,440(V)
Pixel Pitch 0.2505mm x 0.2505 mm 0.2331 x 0. 2331 mm
Contrast Ratio 1000 : 1(Typ.)
Refresh Rate 60 Hz
Response Time 8ms [grey-to-grey] 6ms [grey-to-grey]
Color Gamut 92% NTSC 117% NTSC 110% NTSC
Brightness 300 cd /m2 370 cd/m2 350 cd/m2
Viewing Angle R/L : 89°/ 89°U/D : 89°/ 89°
Surface Treatment Hard coating(3H), Anti-glare treatment
Plug & Play Compatibility Windows 98/ME/2000/XP/Vista/Win7/MAC OS X
OSD Menu Options BRIGHTNESS UP/DOWN, POWER
Operating Temperature 0 ~ 35 °C
Storage Temperature -10 ~ 50 °C
Operating Humidity 10 ~ 90 % RH
Storage Humidity 40 ~ 70 % RH
Dimensions [exc. stand] Approx: 680 x 442x 85 mm Approx: 635 x 375 x 85 mm
Weight 12 kg before packaging [approx] 10 kg before packaging [approx]
Power In Operation HZ30Wi = < 130W @ max brightness
HZ30WiQ = < 150W @ max brightness
HZ27WB = < 120W @ max brightness
DPMS / OFF < 5W [ master on/off switch = 0W]
Energy Saving Mode VESA DPMS
AC Input AC 100V-240V, 50~60Hz
AC / DC Output AC 24V / 6A DC 24V / <7A AC 24V / 6A
VESA Mounting Yes: 200x100 and 100x100mm [M4 Screws]
Accessories Dual link DVI-D cable, IEC Power cord, USB A-toB cable *, User manual
Model I/O Connectors
HZ30Wi Dual Link DVI-D, IEC AC Inlet, Master on/off switch, Kensington Security Lock
4x USB ‘A’ type downstream ports, 1 x USB ‘B’ type upstream port
HZ30WiQ Dual Link DVI-D, Master on/off switch, Kensington Security Lock, 24V DC Power Jack
HZ27WB Dual Link DVI-D, AC Inlet, Master on/off switch, Kensington Security Lock, IEC AC
Inlet, 24V DC Power Jack
Chapter 2 : Specications
Page 3
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Monitor de Hazro
