Hayward HL32950VVSP Manual de usuario

Hayward Pool Products

620 Division Street, Elizabeth NJ 07207

Phone (908)-355-7995

www.hayward.com

VS Omni

Pool Automation Control

Installation Manual

HL32950VVSP HL32900VSP

HL26720VSP HL23520VSP

HL23510VSP

Contents

Before you Begin.....................3

Mounting...............................7

Plumbing................................9

Wiring...................................10

Startup................................22

Conguration........................22

092680 RevB

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Changes or modiﬁcations not expressly approved by Hayward could void the user’s authority to

operate this equipment.

NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-- Consult the dealer or an experienced radio / TV technician for help.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

The term “IC” before the certiﬁcation / registration number only signiﬁes that the Industry Canada

technical speciﬁcations were met.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Table of Contents

Before you Begin.......................................................................................................3

Overview..................................................................................................................4

Mounting

VS Hub.............................................................................................................7

Control Pad.......................................................................................................7

Smart Relay......................................................................................................8

Temperature Sensors........................................................................................9

Plumbing.................................................................................................................9

Electrical Wiring

High Voltage...................................................................................................11

Low Voltage....................................................................................................13

System Startup.........................................................................................................22

Conﬁguration

Pre Programmed Conﬁguration........................................................................25

Typical Conﬁguration.......................................................................................25

Advanced Conﬁguration..................................................................................27

Quick Edit..............................................................................................................42

Control Pad Mounting Template.................................................................................50

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Before you Begin

What’s Included

Check that the following components have been included in your package:

• VS Omni Hub

• Control Pad

• Smart Relay

• 2 Temperature Sensors

• Variable Speed Pump (VSP)

• 15 ft, 3 conductor (red, black and bare wire) communication cable to connect Hub to VSP

• 2 Wiring Whips - 6 ft ﬂexible conduit containing three 12AWG conductors (red, black and

green) for wiring VSP to VS Omni Hub and for Smart Relay installation). A length of white 12

AWG conductor is included to replace red for 115V Smart Relay applications

• Input Power Wiring harness and miscellaneous installation hardware

What’s NOT Included

Some of the additional items that you may need to complete an installation include:

Wire

Wire/conduit for incoming power

Wire for remote heater control and other low voltage devices

Ethernet cable (if not using wiﬁ)

Miscellaneous

Valve actuator to automate pool functions (see page 9)

Flow switch for pump protection/ﬂow monitoring

Mounting hardware for mounting Hub, Control Pad and Smart Relay

Cable/cord connectors to provide knockout strain relief

Wire nut connectors

USB thumbstick (to update ﬁrmware)

Tools Needed

Philips and ﬂat screwdrivers

Wire cutters and strippers

Knife to cut conduit

Drill and drill bits (including 3/8")

Pliers

Level

Accessory Products - Order Separately

HLH485RELAY Smart Relay used for controlling additional pool equipment

FLO Flow Switch used to detect water ﬂow

GVA-24 Valve Actuator

2PC Temperature Sensor for 3rd input

USE ONLY HAYWARD GENUINE REPLACEMENT PARTSUSE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Overview

The Hayward VS Omni is a web enabled pool automation control with a convenient touchscreen

interface. Because it's packaged with a high efﬁciency variable speed pool ﬁlter pump, the VS Omni

is ideal for both retroﬁt and new pool/spa installations. Automatically and remotely control pumps, a

heater, a valve actuator, pool and yard lighting, and more. The VS Omni offers the next generation of

technology to manage pool/spa equipment, allowing communication to web connected computers

and mobile devices. You can now conveniently monitor your pool/spa and change settings anytime,

and from anywhere.

Please read through this manual thoroughly before attempting to install, conﬁgure or operate this

unit. A Quick Start guide is also included to offer concise information to experienced installers.

Features

The standard Hayward VS Omni offers the following functionality:

• controls up to 2 variable speed pumps for pool/spa ﬁltration and water features

• controls up to 2 Smart Relays to turn on/off single speed pumps, pool lights, yard lights, water

features, chemical dispensers and more

• controls up to two valve actuators allowing you to manage two bodies of water (both pool and

spa) or can be used for water features, cleaners, solar heating, etc. (currently requires Hub to be

• controls one conventional heater (electric heatpump or gas) and optional solar heater (for single

body of water applications only)

• inputs for up to 3 temperature sensors or external input devices

• built-in wireless to connect to the home’s router/access point (ethernet port provided for optional

wired connection)

• optional ﬂow switch used to protect pool equipment by detecting water ﬂow

Optional accessories (page 3) can expand the functionality of the VS Omni. Determine your needs

and select the necessary accessories before you begin the installation.

Equipment

VS Omni Hub

All incoming/outgoing wiring will be connected to the Hub. The VS Omni Hub can be powered by

either 115 VAC or 230 VAC. Input power should be constant, not from a timer. If a timer must be

used, set the timer to power the Hub continuously. For convenience, a 6ft Wiring Whip is included

with the VS Omni. This whip is intended to connect the Hub's input power to the variable speed

pump if using 230 VAC. This connection should be made inside of the Hub and will ensure that both

the Hub and pump are powered continuously.

The remaining connections, including the Control Pad, are all low voltage. Depending on your instal-

lation, these connections could be to a heater, Smart Relays, temperature sensors, actuator and a

ﬂow switch.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Control Pad

The Control Pad is weather resistant and comes with a 15 ft cord. Its resistive touch screen with

ﬂip down cover is designed to function year round directly in the elements. Because it plugs into the

Hub, it should be mounted close by, but in a location that is convenient for the user to periodically

view and change pool/spa settings.

The Control Pad features a USB connector for ﬁrmware updates and an Ethernet connector for an

optional direct connection to your router (if wiﬁ won't be used).

Smart Relay

Smart Relays have 15 ft cable that wire to the Hub. They're used to control high voltage 115 or 230

VAC pool equipment like lights, water features, pumps and more. Power to the intended load must

be supplied separately and run through the Smart Relay. Smart Relays are rated for up to 20 amps

at 230 volts.

Temperature Sensors

Depending on your installation, up to 3 temperature sensors may be used. The VS Omni requires

a water temperature sensor for heater operation. If freeze protection is desired, an air temperature

sensor is also required. For solar heating systems, a solar sensor is necessary. Even if your instal-

lation doesn't require the use of temperature sensors, installing water and air sensors provides a

convenience to the user, especially during remote use.

Flow Switch (not included)

An optional ﬂow switch can be used to detect leaks or clogs in the pool/spa plumbing.

Input Power or

Existing Timeclock

Wiring Hub (Optional)

Smart Relay 2

To Feature,

Accessory,

Lights, etc.

Variable

Speed Pump

Filter

Valve

Actuator

Heater

POOL

FROM

POOL

Power

to VSP

Input Power to

Smart Relay 1

Comm. to Smart

Relay 1 (15’)

Comm. to

Heater

Comm. to

Valve Actuator

Comm.

to VSP

To Solar

REMOTE

RELAY

OFFLINE:

ON/OFF

Smart Relay 1

Input

Power

Comm. to Smart

Relay 2 (15’)

Control Pad

To Feature,

Accessory,

Lights, etc.

Wireless

Connection

Ethernet to

Router

Comm. to

Controller (15’)

Sensor 1

(Water Temp.)

Sensor 2

(Air Temp.)

Sensor 3 (Solar OR

External Input)

(Optional)

Flow Switch

REMOTE

RELAY

OFFLINE:

ON/OFF

Wiring Whip

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Installation

Installation Steps

DANGER of Death, Injury or Property Damage if procedure not followed. Power wiring must

be shut off before attempting to install the VS Omni.

The VS Omni is designed to be mounted outdoors at the pool pad. Both the Hub and the Control

Pad are water resistant and can be left out for the winter. Details on each installation step are

shown below:

1. Mounting the equipment (page 7)

VS Omni Hub

Control Pad

Smart Relay

Temperature sensors

Valve actuators (if applicable)

2. Plumbing (page 9)

General Pool Equipment

Flow Switch

3. Electrical Wiring (page 10)

Hub power

Grounding

Low voltage wiring (Pool Pump Communication, Heater, Smart Relays, Temperature Sensors,

Flow Switch, etc.)

5. System Startup and Firmware Upgrade (page 22)

The most common installation technique is described in the included Quick Start Guide. Use this

guide if possible. If the Guide can not be applied to your particular installation, refer to the additional

information in this manual.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Mounting the Equipment

VS Omni Hub

The Hub is contained in a raintight enclosure

that is suitable for outdoor mounting. It must

be mounted a minimum of 6 ft (2 meters) hori-

zontal distance from the pool/spa (or more, if

local codes require). The Hub is designed to

mount vertically with the knockouts facing

downward. Do not mount the Hub inside a

panel or tightly enclosed area.

When selecting a location, note that the stan-

dard cables supplied with the optional ﬂow

switch, temperature sensors, and actuators

are all 15 ft (5m) long. Additional low volt-

age connections will have to be made to the

pump and/or heater. 115 VAC or 230 VAC in-

put power must also be run to the Hub. Try to

mount the Hub in a location where incoming/

outgoing wiring will be easily accessible.

Mount the Hub on a wall or ﬂat surface. Select

mounting hardware that is appropriate for the

mounting surface and material. The Hub has two keyhole type mounting tabs on the top and bottom

of the enclosure requiring a total of 4 fasteners.

Control Pad

The Control Pad comes with a 15 ft cord and plugs into the Hub. It should be mounted in a location

that is convenient for the user to view and change pool/spa settings. When considering the mount-

ing location, make sure there is enough clearance above the enclosure so that the ﬂip door will be

able to be opened fully. Also be sure to allow enough clearance below the Control Pad to access

the USB and Ethernet connectors. For best viewing results, position the Control Pad where it won't

be subjected to direct sunlight.

The Control Pad has two keyhole cutouts on the back of its enclosure. To mount, screw the two

provided fasteners into the mounting surface at the desired location using the template found on

page 54 . Tighten until the bottom of the screw heads are 1/8" off the mounting surface. Position

the Control Pad cutouts over the screw and slide the unit downward. You may have to tighten or

loosen the screws slightly to fully engage the screw heads to get a snug ﬁt.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Smart Relay

The Smart Relay is packaged with a single gang electrical box but can also be used with any existing

comparable standard electrical box with a minimum volume of 16.2 in3. If using 115 VAC, make

sure that there is a Neutral line inside the box before installation. If not, you must run a separate

Neutral wire to power the Smart Relay. This is not a concern if using 230 VAC. Note that conduit and

connections to the included plastic box must be non-metallic.

Find a location within 15 ft of the Hub with convenient access to the pool equipment that you intend

to control with the Smart Relay. Three threaded 1/2" NPT knockouts are provided for high voltage

power coming into the relay and for power out to the pool equipment. A Wiring Whip is included to

aid installation.

The Smart Relay has a manual On/Off button that can be used if communication is lost with the Hub.

Although this button is not functional during normal operation, mount the Smart Relay in an acces-

sible location to use this feature in case of communication loss.

Mount the Smart Relay to a wall or other ﬂat surface using the mounting holes which are designed

to accommodate #8 screws.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Temperature Sensors

Water Sensor

This sensor is used to measure the pool/spa temperature and is installed in the ﬁltration plumbing

after the ﬁlter but before either the solar or conventionally fueled heaters.

1. Drill a 3/8” (10mm) diameter hole in the PVC piping and remove all chips and burrs.

2. Insert sensor until O-ring collar sits ﬂush on the hole.

3. Position hose clamp over the sensor and gently tighten until O-ring makes an adequate seal.

Do not overtighten.

Air Sensor

Mount the air sensor outdoors. IMPORTANT: The air sensor must not be mounted in direct sunlight.

Solar Sensor

For solar applications, mount the sensor near the solar collector array so that it is exposed to the

same sunlight as the collectors. Use additional cable (20 AWG) if necessary.

Optional Valve Actuators

Currently, using an Hayward GVA-24 actuator or equivalent requires that the Hub be powered with

230 VAC. If powering the VS Omni Hub with 115 VAC, an actuator can't be used. For installation,

refer to the mounting instructions included with the unit. After conﬁguring and ﬁrst operating the

valve, note that the internal cams in the actuator may have to be adjusted depending on the way the

actuator is mounted on the valve and the desired valve action.

Plumbing

Optional Flow Switch

Only applicable if leak/clog detection is desired. The ﬂow switch should be plumbed on the return

side at the very end of the pool pad plumbing. This will ensure that if a leak occurs anywhere at the

pool pad, the VS Omni will be able to detect it. Understand that if a leak occurs after the ﬂow switch

(downstream), the VS Omni will not sense a no ﬂow condition.

IMPORTANT: There must be at least a 12” (30cm) straight pipe run before (upstream) the ﬂow switch.

IMPORTANT: To ensure proper operation, verify that the arrow on the ﬂow switch points in the direc-

tion of water ﬂow.

Variable Speed Pump

Refer to the included VS Omni Pump manual for plumbing information.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de Hayward

Hayward

Hayward GOLDLINE Aqua Rite Pro LS Manual de usuario

Hayward

Hayward Goldline Controls Sense and Dispense Total Pool Chemistry... Manual de usuario

Hayward

Hayward 3478 PLDBL3 Manual de usuario

Hayward

Hayward AquaRite AQR15 Manual de usuario

Hayward

Hayward ColorLogic WFBCUS1100 Manual de usuario

Hayward

Hayward VR1000 Manual de usuario

Hayward

Hayward WFL100 ColorLogic Manual de usuario

Hayward

Hayward SwimPure Manual de usuario

Hayward

Hayward KingRay Manual de usuario

Hayward

Hayward Salt & Swim Hoja de datos

Hayward

Hayward WFBRNDBRS Manual de usuario

Hayward

Hayward AQL-CHEM4-ACID Manual de usuario

Hayward

Hayward Sheer 500 Manual de usuario

Hayward

Hayward Pro Logic Manual de usuario

Hayward

Hayward TriStar VS 900 Omni Manual de usuario

Hayward

Hayward Salt & Swim Manual de usuario

Hayward

Hayward Sense and Dispense AQL-CHEM Manual de usuario

Hayward

Hayward CL220BR series Manual de usuario

Hayward

Hayward EasyClear C550 Manual de usuario

Hayward

Hayward Pro Logic Manual de usuario

Hayward

Hayward Control Station Manual de usuario

Hayward

Hayward Stainless Steel Niches Manual de usuario

Hayward

Hayward XStream CC1000 Manual de usuario

Hayward

Hayward Aqua Rite® Pro Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario