Hayward HP40B Manual de instrucciones

SWIMMING POOL HEAT PUMP

Installation & User Manual

Hayward Pool Products Canada, Inc.

T: 1.888.238.7665

Haywardpool.ca

Model HP40B

HP50B

HP65B1

Rev 2017-1

CONTENT

I. Application 4

II. Features 4

III. Technical Parameters 5

IV. Dimensions 6

V. Installation Guide 7

VI. Operation Instruction 10

VII. Testing 13

VIII. Precautions 14

IX. Maintenance 15

X. Troubleshooting 15

A) The Swimming Pool Heat Pump Unit is intended to heat the swimming pool water and regulate

the temperature. Use in any other application will void the warranty.

B) The inlet & outlet connections cannot support any load from another piping system.

C) Make sure outlet air does not hurt any person, animal & plant.

D) The unit must always be powered off before opening the access panel. Always cut the unit’s

main power whenever the access panel is open or removed.

A) All electrical connections must be done by a qualiﬁed electrician and according to national and

local electrical codes. We have provided important safety messages in this manual and on your

heater. Always read and obey all safety messages.

B) You will need to set the water temperature you desire.

C) Always install the machine outdoors, while respecting the minimal clearances needed for proper

operation and heating. DO NOT place the unit next to shrubs, fences, etc. which can block

the air inlet. These locations deny the unit a continuous source of fresh air which reduces its

efﬁciency and may prevent adequate heat delivery.

D) All Hayward Heat Pumps must be installed in accordance with all applicable National and Local

codes. In the absence of local codes, refer to the latest edition of the Canadian Electrical Code

(CEC).

E) The unit will automatically start up when there is proper ﬂow and available power.

F) If the unit is stopped for an extended period of time or winterized, it must be drained of all water.

You will need to disconnect the IN and OUT water connections. Then the unit must then be tilted

or blown out with air until all water is out.

G) Do not insert any objects into the air outlet. Do not attempt to disassemble the fan at any time.

H) If at any time there is an abnormal noise, smell, smoke, electricity leakage, please switch off

power immediately and contact your local dealer. All repairs must be performed by a qualiﬁed

technician.

I) Do not store combustible or ﬂammable material near unit.

WARNING

PRECAUTIONS

I. APPLICATION

II. FEATURES

1. For your comfort and pleasure, set swimming pool water temperature efﬁciently and economically.

2. All technical parameters are factory set. Please refer to technical parameter table.

1. Highly efﬁcient titanium heat exchanger.

2. Sensitive and accurate temperature control and water temp display.

3. Environment-friendly R410A refrigerant.

4. High pressure, low pressure & water ﬂow protection system.

5. Exceeding low temperature auto stop protection.

6. Temperature controlled compulsory defrosting.

7. International brand compressor.

8. Easy installation and operation.

III. TECHNICAL PARAMETERS

Remarks:

This product has been tested at air temperature of 32°F ~109°F. Efﬁciency cannot be

guaranteed out of these ranges. All parameters will differ under various conditions.

IV. DIMENSIONS

Note: The above diagram is the speciﬁcation diagram of the pool heater, for technician’s

installation and layout reference only.

V. INSTALLATION GUIDE

1. Diagram for Water Piping Connections

2. Electric Wiring Diagram

Note: The diagram is for demonstration purposes only, and layout of the pipes is for reference only.

Note: The swimming pool heat pump must be grounded.

V. INSTALLATION GUIDE

Options for protecting devices and cable speciﬁcation.

Pump protecting device, cable speciﬁcation is subject to user’s option.

1. Installation Instruction and Requirements:

All electrical connections must be done by a qualiﬁed electrician and according to national and local electrical

codes. We have provided important safety messages in this manual and on your heater. Always read and

obey all safety warnings. All Hayward Heat Pumps must be installed in accordance with all applicable National

and Local codes. In the absence of local codes, refer to the latest edition of the Canadian Electrical Code

(CEC).

A. Installation

1. Always install the machine outdoors, while respecting the minimal clearances needed for proper operation

and heating. DO NOT place the unit next to shrubs, fences, etc. which can block the air inlet. These

locations deny the unit a continuous source of fresh air which reduces its efﬁciency and may prevent

adequate heat delivery.

2. Mount the unit on a sturdy base, preferably a concrete slab. The base should be completely isolated from

the building foundation wall to prevent the possibility of sound or vibration transmission into the building.

3. The pool heat pump is designed for outdoor installation and should not be installed in a fully

enclosed area, such as a shed, garage, etc. Recirculation of cold discharged air back into the evaporator

coil will greatly reduce unit heating capacity and efﬁciency.

Note: The above data is for an electrical cord of less than 10 m. If electrical cord is > 10 m, wire diameter must

be increased. The signal cable can be at maximum 50 m.

Air is pulled through the evaporator coil and discharged through the side grille. A minimum clearance of 98

inches should be allowed on the air outlet side for unrestricted air discharge. The unit must not be installed

under a porch. Any other side of the unit should be located at least 28 inches from a wall or from any other

obstruction for unrestricted air intake and service access.

4. The piping sequence is as follows: pool > pool pump > ﬁlter > heater > check valve > chemical feeder

> pool. Automated chlorine distribution systems, if used, must be placed downstream of the heater to

minimize harm to the pool equipment. Use rigid PVC piping if possible (SCH40 or SCH80). All joints should

be glued with PVC glue. When the piping installation is complete, operate the pool pump and check the

system for leaks. Then, check the ﬁlter pressure gauge to verify that there isn’t any indication of excessive

pump head pressure.

You can also make the connections using high-pressure ﬂexible hose, but make sure the hose can

withstand high pressure. The installation of a heat pump bypass is not necessary unless the water ﬂow

exceeds 75 GPM.

5. It is also normal to see water dripping from the drain at the base pan of the unit. While your pool heat

pump is in the heating mode, a large volume of warm and humid air passes over the evaporator and

causes condensation. To check if there really is a leak, you must stop the heat pump and leave the pool

pump running for at minimum 5 hours. If water is still coming out of your heat pump after this period, then

call your dealer for service.

B. Wiring

1. The wiring of your pool heat pump should be performed by a qualiﬁed electrician in accordance with local

requirements. A properly-sized breaker and copper wire must be used. Check the heat pump data

label for required maximum breaker size. Because all metals have different electrical potentials, all

metal and electrical components of the pool system must be bonded together. This includes the metal

framework of the pool, the light, the pump, the ﬁlter (if made out of metal), the heater, any automatic

chlorine generator, and any other metal or electrical equipment. On some older pools, this substructure

bond wire may not exist. In these cases, a 6 to 8 foot solid copper rod must be driven into the ground

near the equipment. All electric and metal components must then be bonded to each other, and then to

the copper rod.

2. The wiring of your pool heat pump must be performed by a qualiﬁed electrician in accordance with national

and local requirements.

3. Set leakage protector according to the local code for wiring (leakage operating current ≤ 30mA).

4. The layout of power cable and signal cable should be orderly and not affecting each other.

C. Switch on after ﬁnishing all wiring, installation and double checking.

V. INSTALLATION GUIDE

VI. OPERATION INSTRUCTION

Permanent Display

LED Controller

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Bomba de calor de Hayward

Hayward

Hayward HP50CLEE Manual de servicio

Hayward

Hayward Energypro Manual de servicio

Hayward

Hayward HP50HA Manual de usuario

Hayward

Hayward ECLI15MA Manual de servicio

Hayward

Hayward Powerline EcoPac 81502 Manual de servicio

Hayward

Hayward EnergyLine pro Manual de usuario

Hayward

Hayward S.Line Pro Fi 25kW Manual de usuario

Hayward

Hayward SUMHEAT HP5131DT3 Manual de servicio

Hayward

Hayward HP3005AT1RM Manual de servicio

Hayward

Hayward HP50B Manual de instrucciones

Hayward

Hayward Powerline 81504 Manual de servicio

Hayward

Hayward HeatRelax Guía rápida

Hayward

Hayward Universal H-Series Low NOx Manual

Hayward

Hayward Energyline Pro Inverter Series Manual de servicio

Hayward

Hayward EnergyLine pro Manual de servicio

Hayward

Hayward HP55TR Manual de servicio

Hayward

Hayward HP50CL Manual de servicio

Hayward

Hayward AccessLine HP3051DT3HM Manual de servicio

Hayward

Hayward HP50AEE Manual de servicio

Hayward

Hayward Heat Pump Manual de usuario

Hayward

Hayward SUPREME HP60TR Manual de servicio

Hayward

Hayward summit SUM25TA Manual de usuario

Hayward

Hayward ENERGYLINE INVERTER Series Manual de usuario

Hayward

Hayward EnergyLine pro Manual de servicio

Manuales populares de Bomba de calor de otras marcas

MICROWELL

MICROWELL HP 1000 GREEN Manual de usuario

Sanyo

Sanyo SAP120FCH Manual de usuario

Daikin

Daikin EHYHBH05AA Manual de usuario

Panasonic

Panasonic WH-SDF03E3E5 Guía

Bryant

Bryant 544B Manual de usuario

Airxcel

Airxcel 45000 Series Manual

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manual de usuario

Dimplex

Dimplex LI 16I-TUR Guía del usuario

Carrier

Carrier WSHP Open v3 Guía de configuración rápida

TGM

TGM CTV14CN018A Manual de usuario

Carrier

Carrier 38MGQ Series Manual de usuario

Kokido

Kokido K2O K880BX/EU Guía de solución de problemas

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guía rápida

Carrier

Carrier 48EZN Manual de usuario

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Instrucciones de funcionamiento

Ariston

Ariston NIMBUS Manual de usuario

Weishaupt

Weishaupt WWP L 7 Guía del usuario

GE Zoneline AZ85H09EAC Manual de usuario