Hayter R324T Manual de usuario

OPERATOR'S MANUAL

RR332244TT

HIGH OUTPUT

ROTARY MOWER

Code 994E

English Version

CODE FROM SERIAL NO:

994E 290080001 MANUAL PART NO: 111-1039 (REV.B)

Issue: 08.05.09

ATTENTION

THIS SYMBOL MEANS

BE ALERT!

YOUR SAFETY IS INVOLVED

READ THIS MANUAL BEFORE USING THE R324T MOWER.

IT IS ESSENTIAL THAT OPERATORS STUDY IT FOR THEIR OWN SAFETY.

ALL OPERATORS SHOULD SEEK AND OBTAIN PROFESSIONAL AND

PRACTICAL INSTRUCTIONS ON THE SAFE USE OF THE MOWER. THESE

SERVICES ARE AVAILABLE THROUGH HAYTER LIMITED OR HAYTER APPROVED

COMMERCIAL DEALERS.

CONTENTS

1.4 1.4

CONTENTS

SAFETY PRECAUTIONS.

Training.

Preparation.

Operation.

Maintenance and storage.

Decals.

EC CONFORMITY INFORMATION.

Noise levels / Vibration levels.

EC Declaration of Conformity.

INTRODUCTION.

SPECIFICATIONS.

Engine.

Transmission system.

Cutterdeck drive system.

Cutterdeck lift system and steering.

Hydraulic system.

Vehicle specifications.

Operator controls.

Instrumentation.

Weight and dimensions.

Recommended lubricants and hydraulic fluids.

Cutterdecks.

OPERATING THE MOWER.

Safety notice.

Operator presence controls.

Identification of controls.

Braking system.

Throttle control.

Travel.

Work/Transport modes.

Transport latches.

Differential lock.

Travel control pedals.

Forward travel speed backstop lever.

Operator platform latching mechanism.

Adjustable steering column.

Folding the R.O.P.S

Operator seat.

Warning systems.

Audible warning horn.

Ignition key.

Engine pre-heat indicator light.

Page No.

1.6 - 1.13

1.6

1.6 - 1.7

1.7 - 1.9

1.10

1.11 - 1.14

1.15 - 1.16

1.15

1.16

1.17

1.18 - 1.24

1.18

1.19

1.20

1.21

1.22

1.23

1.24

1.25 - 1.40

1.25

1.26

1.27

1.28

1.29

1.30

1.31

1.32 - 1.33

1.34

1.35

1.36

CONTENTS

1.5 1.5

CONTENTS Continued.

Fuel level gauge.

Hourmeter.

Transmission neutral indicator light.

Cutterdeck drive switch indicator light.

Parking brake indicator light.

Hydraulic return filter indicator light.

Hydraulic transmission filter indicator light.

Transmission system ‘Work’ mode indicator light.

Cutterdeck position control.

Cutterdeck drive engagement.

Starting the engine.

Stopping the engine.

General operating hints.

Cutterdeck gerneral information.

MAINTENANCE.

General safety and good practice

Engine.

Running in period.

Running in period - at first 50 hours.

Daily and before use.

Every 50 hours.

Every 250 hours.

Every 500 hours.

Cutterdecks.

Cutterblades.

Raising the mower off the ground.

Towing the mower.

GRASS CUTTING FAULTS.

TROUBLE SHOOTING.

ELECTRICAL CIRCUIT DIAGRAM.

TRANSMISSION/BRAKE HYDRAULIC CIRCUIT.

HYDRAULIC CIRCUIT DIAGRAM.

WARRANTY.

NOTES.

CUSTOMER INFORMATION.

Page No.

1.36

1.37

1.38

1.39

1.40

1.41 - 1.42

1.43 - 1.61

1.43 - 1.44

1.45

1.45 - 1.46

1.47 - 1.50

1.51

1.52

1.53 - 1.56

1.57

1.57 - 1.58

1.59

1.60 - 1.61

1.62 - 1.63

1.64 - 1.70

1.71 - 1.74

1.75 - 1.76

1.77 - 1.78

1.79

1.80

1.81

1.6 1.6

SAFETY PRECAUTIONS

TRAINING

Read the instructions carefully. Be familiar with the controls and the proper use of the equipment. Learn

how to stop the mower quickly in an emergency.

Never allow children or people unfamiliar with these instructions to use the mower. Local regulations

may restrict the age of the operator.

Never mow while people, especially children, or pets are nearby.

Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or

their property.

Do not carry passengers.

All drivers should seek and obtain professional and practical instruction. Such instruction should emphasise:

The need for care and concentration when working with this machine.

The need to slow down when making tight turning manoeuvres. Failure to take adequate care can affect

stability leading to loss of control of the machine particularly when operating in transport mode.

Control of a ride-on-machine sliding on a slope will not be regained by application of the brake.

The main reasons for loss of control are:

- Insufficient wheel grip.

- Being driven too fast.

- Inadequate braking.

- The type of machine is unsuitable for the task.

- Lack of awareness of the effect of ground conditions, especially slopes.

- Incorrect load distribution.

PREPARATION

Check that the machine complies with all applicable regulations, including those in force when used on

the public highway.

While mowing, always wear substantial footwear and long trousers. Do not operate the equipment when

barefoot or wearing open sandals. Eye protection should be worn.

Thoroughly inspect the area where the equipment is to be used and remove all objects which can be

thrown by the machine.

Never operate the machine without first checking that the operator platform latching mechanism is fully

engaged and in good working order, refer - ‘OPERATOR PLATFORM LATCHING MECHANISM’.

READ THIS MANUAL BEFORE USING THE R324T MOWER, IT IS ESSENTIAL THAT

OPERATORS STUDY IT FOR THEIR OWN SAFETY.

THE FOLLOWING PRECAUTIONS MUST BE TAKEN TO HELP PREVENT ACCIDENTS.

A CAREFUL OPERATOR WHO USES COMMON SENSE IS THE SAFEST OPERATOR.

1.7 1.7

SAFETY PRECAUTIONS

PREPARATION Continued.

Ensure that the cutterdecks are fully raised with the latches and safety locks engaged in position before

transporting the mower.

Replace faulty silencers.

Check the condition of the tyres and ensure that they are inflated to the correct pressures, refer -

SPECIFICATIONS.

This is particularly important if the machine is to be taken on the public highway.

Check that the mower is in good working order, paying particular attention to the brakes and steering.

Also ensure that the forward/reverse speed control pedals move freely to neutral when released.

Before use, always visually inspect to see that the blades, blade bolts and cutterblades are not worn or

damaged. Replace worn or damaged components.

Check the mower hydraulic system, particularly the hydraulic hoses, fittings and hose supports. Worn,

crushed or damaged hoses can burst, with risks to health and damage to the machine and surrounding

turf areas.

After refuelling and adding oil to the hydraulic oil tank ensure that the caps are replaced securely.

Check that all linkages, connections and pivot nuts are secure and that wheel nuts are torqued correctly,

refer - SPECIFICATIONS.

Before operating the machine, ensure that there are no foreign objects or liquids on the platform or ped-

als - ALWAYS KEEP THE OPERATOR PLATFORM CLEAR/CLEAN.

Always make sure that the folding R.O.P.S is secured in its vertical operating postion before use.

OPERATION

Do not touch the totating cutterblades.

Do not operate the engine in a confined space where dangerous carbon monoxide fumes can collect.

Mow only in daylight or in good artificial light.

Before attempting to start the engine, engage the parking brake, disengage the cutterdeck drive system

and ensure that the forward/reverse speed controls are in the neutral position.

Never operate the machine without first checking that the operator platform latching mechanism is fully

engaged and in good working order, refer - OPERATOR PLATFORM LATCHING MECHANISM.

Stored energy devices are charged when the outer wing units are in the transport position. Always oper-

ate the relevant lift controls to provide hydraulic support for the wing units suspensions before attempt-

ing to release the transport latches.

1.8 1.8

SAFETY PRECAUTIONS

OPERATION Continued.

Do not use on a slope of more than 14 degrees. Care should be taken when using the mower on any slope

where ground conditions are such that there may be a risk of the mower rolling over. The requirements

of SI 1998 No. 2306 “Provision and Use of Work Equipment Regulations” should be considered.

Stability angles given are maximum figures for a machine equipped with a R.O.P.S and are for guidance

only. Particular conditions such as wet grass or uneven ground may not permit safe operation on the

slope limits stated.

Remember there is no such thing as a "safe" slope. Travel on grass slopes requires particular care. To

guard against overturning or loss of traction when travelling or mowing on a slope:

- Exercise extreme care when changing direction on a slope.

- Do not stop or start suddenly.

- Engage drive slowly.

- Keep machine speed low.

- Avoid tight turns.

- Stay alert for humps, hollows and other hidden hazards.

- Keep away from sharp inclines and steep drops.

- A thorough risk assessment should be carried out by a competent

person before travelling or mowing on a slope.

Never park on a slope.

3DA176-A

14 Degree Slope

Ground level

1.9 1.9

SAFETY PRECAUTIONS

OPERATION Continued.

Watch out for traffic when crossing or near roadways.

Use extreme caution when reversing.

Disengage the cutterdeck drive system before crossing surfaces other than grass.

When using the machine, never direct the discharge of material towards bystanders or allow anyone

near the machine while in operation.

Never operate the mower with damaged guards, shields or without safety protective devices in place

and in good working order.

Do not change the engine governor settings or overspeed the engine. Operating an engine at excessive

speed may increase the risk of personal injury.

Before leaving the operator's position:

- Disengage the drive to the cutterdecks.

- Lift cutterdecks to the transport position and securely lock the safety latches

or alternatively lower cutterdecks to the ground.

- Ensure the transmission is in neutral and engage the parking brake.

- Stop the engine and remove the ignition key.

Engage the parking brake, disengage the drive to the cutterdecks, stop the engine and remove ignition

key :

- Before releasing blockages.

- Before checking, cleaning or working on the mower.

- After striking a foreign object. Inspect the mower for damage and make

repairs before restarting and operating the equipment.

- If the machine starts to vibrate abnormally ( check immediately ).

- Before refuelling.

- Before making cutterdeck adjustments.

Disengage the drive to the cutterdecks when transporting or not in use.

Reduce the throttle setting during engine run-out.

Never work on the mower when the engine is running.

Always keep feet and hands well away from the cutterblades when making adjustments.

Never operate the mower without first checking that the operator platform is securely latched.

Always wear the seat belt when the folding R.O.P.S is in its vertical operating position.

Never wear the seat belt when the folding R.O.P.S is NOT in its vertical operating position.

Pay particular attention when operating due to the additional weight towards the front of the machine.

1.10 1.10

SAFETY PRECAUTIONS

MAINTENANCE AND STORAGE

Take care when rotating a cutterblade as this can cause other cutterblades to rotate.

When the machine is to be parked, stored or left unattended, lift the cutterdecks to the transport position

and engage the safety locks or lower the cutterdecks to the ground.

Keep all nuts, bolts, and screws tight to be sure the equipment is in safe working condition.

Allow the engine to cool before storing in any enclosure.

To reduce the risk of fire, keep the engine, silencer, fuel tank and battery compartment free of grass,

leaves or excessive grease.

Frequently check fuel lines and fittings for cracks or leaks and replace if necessary.

Replace worn or damaged parts for safety.

Ensure that all safety decals are properly secured and in good condition.

If the fuel tank has to be drained, this should be done outdoors.

Be careful during adjustment of the machine to prevent entrapment of the fingers between moving blades

and fixed parts of the machine.

Never attempt to disconnect any part of the hydraulic system before de-pressurisation. This may be

achieved by lowering all cutterdecks to the ground, stopping the engine and removing the ignition key.

Avoid skin or eye contact with hydraulic or diesel fluids. Wear protective clothing.

Leaking fluids under pressure can penetrate the skin or eyes, causing serious injury.

Always use a piece of cardboard or paper when searching for leaks.

Health and Safety at Work Act:

In accordance with section 6 of the Health and Safety at Work Act 1974, the R324T Rotary Mower has

been designed and constructed so that, in so far as is reasonably practical, it will not endanger the safe-

ty and health of those working with it. This is, however, subject to the machine being properly used and

maintained according to the conditions stated in this manual and elsewhere, which have been found

necessary as a result of the research and testing of Hayter Limited.

Tabla de contenidos

Otros manuales de Cortacésped de Hayter

Hayter

Hayter MT313 Manual de usuario

Hayter

Hayter Harrier 48 Pro Guía del usuario

Hayter

Hayter Hobby 41 Manual de usuario

Hayter

Hayter Envoy 36 Guía del usuario

Hayter

Hayter 005G Guía del usuario

Hayter

Hayter Harrier 48/56 Pro Guía del usuario

Hayter

Hayter Spirit 41 617J Guía del usuario

Hayter

Hayter Harrier 48 Pro Guía del usuario

Hayter

Hayter CODE377A Manual de usuario

Hayter

Hayter CODE373A Manual de usuario

Hayter

Hayter Motif 41 Push Guía del usuario

Hayter

Hayter Harrier 56 BBC Guía del usuario

Hayter

Hayter Harrier 48/56 Pro 496G Guía del usuario

Hayter

Hayter Harrier 48 / 56 BBC Guía del usuario

Hayter

Hayter Harrier 56 560G Guía del usuario

Hayter

Hayter Harrier 41 Electric Guía del usuario

Hayter

Hayter LT324 Manual de usuario

Hayter

Hayter Hayterette 005A Guía del usuario

Hayter

Hayter CODE378A Manual de usuario

Hayter

Hayter Sprint 41 616E Guía del usuario

Hayter

Hayter Harrier 48 BBC Guía del usuario

Hayter

Hayter Jubilee 422V Guía del usuario

Hayter

Hayter HERITAGE M10 Manual de usuario

Hayter

Hayter Harrier 41 PRO FS Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario