Hatteland 1 Series Manual de usuario
1
IND100064-20
Operation
User Controls
USER CONTROLS OVERVIEW
The units are available in two dierent factory user control congurations as illustrated below.
#1: Potmeter & buzzer (introduced Q4 2008) including keypad controls with its Status LED Ring. Brightness
for the unit is adjusted by using the potmeter. The tactile keypad control provide access to the conguration
menu and Direct Access / Hotkeys functionality. The speaker/buzzer function provide audible alarm
functionality routed via the Multifunction Cable.
#2: The tactile only keypad controls with 5 push buttons (introduced Q2 2007) and the Status LED Ring.
The keypad provide the user to control brightness, access the conguration menu and use the Direct
Access / Hotkeys functionality. The LED ring will provide feedback for various status or modes that the unit
can or currently operates in.
Power ON:
To turn the unit on, push the navigator MENU button inwards and release it instantly. The unit will start
searching for signal sources. A green led will move around the led ring to indicate the search procedure.
Please consult the STATUS LED overview later in this chapter for the various LED patterns that can occur.
Power OFF:
To turn the unit o, push the navigator MENU button inwards and hold it down for 6 seconds. After the rst
3 seconds the menu will appear. 3 seconds later the unit is turned o and all LED indicators will turn red.
You can now release the power button. Please consult the STATUS LED overview on the next page for the
various LED patterns that can occur.
Speaker/Buzzer Potmeter Keypad
Keypad
2
Operation
User Controls
IND100064-20
MENU function as:
Power On/O & On Screen Display (OSD) menu access.
LEFT (◄) function as:
Direct Access / Hotkey, exit the current function and navigate to the previous OSD menu.
RIGHT (►) function as:
Direct Access / Hotkey, enter sub-menu & execute/set selected function.
UP (+) function as:
Increase brightness, adjust positive values, visual movement, OSD menu navigating upwards & conrm.
DOWN (-) function as:
Decrease brightness, adjust negative values, visual movement, OSD menu navigating downwards & conrm.
DIRECT ACCESS / HOTKEY FUNCTION
You can access a number of functions from within the OSD Menu which is normally only accessible by
browsing through the OSD Menu and locate the function manually. The Direct Access function are assigned
to the Left and Right buttons to function as hotkeys. Note that some functions are dual (increase/decrease)
or just single (swap/next). Those with single functionality both the left and right keypad button will perform the
same action.
To congure the Direct Access / Hotkeys functionality, just press one of the buttons inwards and release it
instantly, detection time is immediate.
Available assigned functions for Direct Access are: Brightness, PIP Size, Main Source, Second Source,
Alpha Blend, Video Scaling, Swap Source, Test Pattern and No Function.
Please review the “OSD Menu Function” chapter for conguring the direct access / hotkeys functionality.
Push Buttons
+Direct Access / Hotkeys
Left / Hotkey button
Status LED Ring
Right / Hotkey button
Up (+) button
Down (-) button
Power / Menu button
KEYPAD FUNCTIONALITY
3
Operation
IND100064-20
Status LED Overview
Status LED Overview
The unit features a multi purpose indicator LED status ring which through dierent patterns. Realtime
activity gives back the status of the signal detected, power on/o, calibration, menu activity and more.
The LEDs are multicolored which either illuminate green or red, based on the activity.
OFF (No power connected)
8 LED OFF
OFF (Standby, power detected)
8 RED LED STATIC ON
ON (Signal Search)
1 GREEN LED MOVEMENT looping.
ON (Signal OK)
8 GREEN LED STATIC ON
ON (No Signal)
4 RED LED STATIC ON
ON (Menu Delay)
7 GREEN LED STATIC +
1 LED OFF MOVEMENT doing 1 loop.
OFF (Shutdown)
1 RED LED MOVES for 3 sec. After additional
3 secs, all leds turns RED.
ON (Calibrated)
4 GREEN LED STATIC ON
ON (Calibrated +)
4 GREEN LED STATIC ON + where 1 show
BRIGHTNESS INDICATION POSITION
ON (Calibrated -)
4 GREEN LED STATIC ON + where 1 show
BRIGHTNESS INDICATION POSITION
For ECDIS Calibrated Products
For units that are ECDIS calibrated from factory, the following LED pattern (Calibrated) indicates that the
backlight/brightness is at calibrated level. (Calibrated +) or (Calibrated -) means that the
brightness adjustment value is above or below the calibrated brightness level. Fine adjust the brightness
in terms of decreasing or increasing the value until the pattern for (Calibrated) is reached.
Otros manuales para 1 Series
1
Este manual sirve para los siguientes modelos
3
Otros manuales de Monitor de Hatteland
Hatteland
Hatteland HM 19T14 Manual de usuario
Hatteland
Hatteland HD 08T21 STD-xxx-Fxxx Manual de usuario
Hatteland
Hatteland JH 21C06 Manual de usuario
Hatteland
Hatteland HD 24T21 MMD Manual de usuario
Hatteland
Hatteland HD 12T21 STD-xxx-Fxxx Manual de usuario
Hatteland
Hatteland JH 19T01 MIL Manual de usuario
Hatteland
Hatteland JH 15T17 MMD Series Manual de usuario
Hatteland
Hatteland JH 10T08 Manual de usuario
Hatteland
Hatteland X series Manual de usuario
Hatteland
Hatteland HD 12T21 STD-xxx-Fxxx Manual de usuario
Hatteland
Hatteland JH 10T06 MMD Manual de usuario
Hatteland
Hatteland HD 12T21 STD-xxx-Fxxx Manual de usuario
Hatteland
Hatteland JH 21C09 DSK Manual de usuario
Hatteland
Hatteland JH 21C07 MDK Manual de usuario
Hatteland
Hatteland HD 12T04 series Manual de usuario
Hatteland
Hatteland HD 08T21 STD-***-F SERIES Manual de usuario
Hatteland
Hatteland HM 20T07 MIL Manual de usuario
Hatteland
Hatteland JH 15T03 STD Manual de usuario
Hatteland
Hatteland JH 15T17 MMD Series Manual de usuario
