HARVEST 500A1 Manual de usuario
010-0500A1 OPR
Revised 7/22
OPERATION MANUAL
Model 500A1
Moisture Sensor Kit for Large Square Balers
Forage Harvester
2
DECLARATION OF APPLICATION OF ESSENTIAL REQUIREMENTS OF THE DIRECTIVE
2006/42/ EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 17, MAY, 2006 AND
OTHER RELEVANT EU DIRECTIVES: The Harvest Tec Hay Moisture Sensor Kit conforms with the
Directive and other relevant EU directives.
SERVICE DUTY OF THE PARTIALLY COMPLETED MACHINE: The Harvest Tec Hay Moisture
Sensor Kit will only be put into service after installed on a hay baler that has been declared to
conform with the Directive.
Noise from the Harvest Tec Moisture Sensor Kit does not exceed 70 dB (A).
Manufacturers Name Plate
Harvest Tec LLC.
Manufactured at and correspondence to:
2821 Harvey Street Hudson, WI 54016
USA
Model
Build Date
Serial No.
PERSON AUTHORIZED TO PROVIDE INFORMATION ON THE MACHINE AND WHO MAKES
THIS DECLARATION:
Jeffery S. Roberts, President, Harvest Tec, LLC.
Signed in Hudson, WI, USA on May 21, 2011
3
500A1 OPERATIONS MANUAL TABLE OF CONTENTS
PAGE
SAFETY
4
OPERATION OF THE 500A1 MOISTURE SENSOR KIT
5
INTRODUCTION AND REQUIREMENTS
5
BALER MONITOR SETUP
6
SYSTEM SETUP
6-9
ADJUST THE MOISTURE ALARM
10
OPTION TO TURN OFF/ON ALL ALARMS OR BEEPS
11-12
PARTS BREAKDOWN
13
CONTROLS AND HARNESSES
13
STARWHEEL SENSORS
14
COMMON QUESTIONS
15
TROUBLESHOOTING
16
WARRANTY
17
4
Safety
Carefully read all safety signs in this manual and on the moisture sensor kit before use. Keep signs
clean and clear of obstruction to view. Replace missing or damaged safety signs. Replacement
signs are available from your local authorized dealer. See your installation manual under the
replacement parts section for the correct part numbers.
Keep your moisture sensor kit in proper working condition. Unauthorized modifications to the
moisture sensor kit may impair the function and/or safety of the machine.
Carefully read and understand all safety signs before installing or servicing.
Safety Signs
Number 1
Disconnect power before servicing.
Part no. DCL-8003
Number 2
Read and understand the operator’s manual
before using or working around the equipment.
Part no. DCL-8000
5
OPERATION OF 500A1 MOISTURE SENSOR KIT
Introduction and Requirements
Thank you for purchasing a 500A1 Moisture Sensor Kit and congratulations. The 500A1 Moisture
Sensor Kit is designed to work with any AGCO 2150-2190 or Challenger LB33B-LB44B large square
balers Model Year 2008 and newer. If you do not have the AGCO Bale Chute Scale option you will
need the parts listed below:
AGCO part numbers:
700733748 Square Baler Module (SBM)
700733750 Wire Harness (only needed on 2008-2011 Balers)
The Square Baler Module (SBM) and the Square Baler Controller (SBC) must run on version 3.0 or
higher. Please consult the Baler Operation Manual for more information.
For instructions on How to Mount the 500A1 to the Baler please refer to the 500A1 Installation
Manual.
6
Baler Monitor Setup
System Setup
1. To view moisture from the 500A1 Moisture Sensor begin setup at the main baler screen.
Select the WRENCH icon (arrow A) which is the fourth icon down on the right side of the
screen-the right selection menu.
2. The service screen displayed below should appear. Press the ABicon (arrow B) located at
the top right of the selection menu.
A
B
7
3. The A B screen will appear. Next select the A B 2 (arrow C) icon which is the second from the
top on the far right selection menu.
4. The A B 2 screen will appear. The Harvest Tec On/Off selection icon can now be selected.
To turn the Harvest Tec Moisture Sensor On (signified by a green check mark) or Off
(signified by a red X) navigate to the box and select by pressing On/Off (arrow D). Once the
Harvest Tec Moisture Sensor has been turned On/Off you can navigate back to the main baler
work screen by pressing the BALER (arrow E) icon on the top right of the selection menu.
C
C
C
E
D
8
5. The main baler work screen will appear. Select the container or option (arrow F) where you
have positioned it on this screen to view and adjust moisture. Note: This can be done on the
primary or secondary baler work screen. The screen has been or can be customized for
viewing containers or options as you would like and as guided in the baler manual.
6. Once the user has selected the menu option or container they would like to change, a drop
down list (arrow G) will appear. The Moisture option (arrow H) should be at the bottom of
the drop down container or option selection list.
F
H
G
9
7. Select the desired moisture and it will appear on the baler work screen as pictured below.
The two values indicated in the moisture option are as follows: current moisture / last bale
average moisture (arrow I).
I
10
To Adjust the Moisture Alarm
1. From the main baler screen, select the third icon down the right selection menu that shows a
diamond beside a baler (arrow J).
2. To adjust the moisture alarm set point select the box option to the right of the moisture
droplets (arrow K) and adjust to the desired moisture limit. To return to the baler work screen,
press the baler icon at the top right of the selection menu (arrow L).
C
L
K
J
Tabla de contenidos
