Hard Wire SC-2 Manual de usuario
DECLARATION OF CONFORMITY
Manufacturer’s Name: Harman Music Group
Manufacturer’s Address: 8760 S. Sandy Parkway
Sandy, Utah 84070, USA
declares that the product:
Product name: SC-2
Product option: All (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.)
conforms to the following Product Specifications:
Safety: IEC 60065 -01+Amd 1
EMC: EN 55022:2006
EN 55024:1998
FCC Part 15
Supplementary Information:
The product herewith complies with the requirements of the:
Low Voltage Directive 2006/95/EC
EMC Directive 2004/108/EC.
RoHS Directive 2002/95/EC
WEEE Directive 2002/96/EC
With regard to Directive 2005/32/EC and EC Regulation 1275/2008 of 17 December 2008, this product is designed, produced, and classified as Professional Audio
Equipment and thus is exempt from this Directive.
With regard to Directive 2005/32/EC and EC Regulation 278/2009 of 6 April 2009, this regulation applies to Class A (single output) external power supplies.The
external power supply used with this product is a multi-output power supply and thus is exempt from this Directive.
Roger Johnsen
Vice-President of Engineering
8760 S. Sandy Parkway
Sandy, Utah 84070, USA
Date: October 4, 2010
European Contact:Your local HardWire®Sales and Service Office or
Harman Music Group
8760 South Sandy Parkway
Sandy, Utah 84070 USA
Ph: (801) 566-8800
Fax: (801) 568-7583
Warning
For your protection, read the following:
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Do not use this apparatus near water.
5. Clean only with dry cloth.
6. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
8. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
9. Unplug this apparatus during lightning storms or when
unused for long periods of time.
10. No user serviceable parts inside. Refer all servicing to
qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or
has been dropped.
11.WARNING:To reduce the risk of fire or electric shock, do
not expose this apparatus to rain or moisture.
12. Refer to labels on the unit, including bottom cover, or other
markings and pertinent information.
ELECTROMAGNETIC
COMPATIBILITY
This device complies with part 15 of the FCC
Rules and the Product Specifications noted on the
Declaration of Conformity. Operation is subject to
the following two conditions:
• this device may not cause harmful interference,
and
• this device must accept any interference received,
including interference that may cause undesired
operation.
Operation of this unit within significant
electromagnetic fields should be avoided.
• use only shielded interconnecting cables.
If you want to dispose of this product, do not mix it with general household waste.
There is a separate collection system for used electronic products in accordance with
legislation that requires proper treatment, recovery, and recycling.
Private households in the 25 member states of the EU, in Switzerland and Norway may return their
used electronic product free of charge to designated collection facilities or to a retailer (if you
purchase a similar new one).
For countries not mentioned above, please contact your local authorities for a correct method
of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery,
and recycling and thus prevent potential negative effects on the environment and human health.
WARRANTY:
We at HardWire®are proud of our products and back-up each one with the following warranty:
Please register online at hardwirepedals.com within ten days of purchase to validate this warranty.
HardWire warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship
under normal use and service.
HardWire liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect,
provided the product is returned to HardWire WITH RETURN AUTHORIZATION, where all parts and labor will be covered
up to a period of one year (this warranty is extended to a period of six years when the product has been properly registered
through our website). A Return Authorization number may be obtained from HardWire by telephone.The company shall not
be liable for any consequential damage as a result of the product’s use in any circuit or assembly.
Proof-of-purchase is considered to be the burden of the consumer.
HardWire reserves the right to make changes in design, or make additions to, or improvements upon this product without
incurring any obligation to install the same on products previously manufactured.
The consumer forfeits the benefits of this warranty if the product’s main assembly is opened and tampered with by anyone
other than a certified HardWire technician, or if the product is used with voltages outside of the range suggested by the
manufacturer.
The foregoing is in lieu of all other warranties, expressed or implied, and HardWire neither assumes nor authorizes any
person to assume any obligation or liability in connection with the sale of this product. In no event shall HardWire or its
dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes
beyond their control.
NOTE: The information contained in this manual is subject to change at any time without notification. Some information
contained in this manual may also be inaccurate due to undocumented changes in the product or operating system since
this version of the manual was completed.The information contained in this version of the owner’s manual supersedes all
previous versions.
1
Introduction
More than a remarkable achievement, HardWire®represents a collection of
significant improvements in effects pedals for guitar. HardWire pedals pro-
vide a suite of well-known effects, each with superior tone and control. But
these pedals go above and beyond their peers to provide such distinguishing
features as true bypass and high voltage operation, making them essential
additions to the signal chain of players who know about sound quality and
demand the utmost in performance.
Included Items
• HardWire SC-2 Valve Distortion
• HardWire StompLock™
• Foot Switch Glow Sticker
• Hook-and-loop Pedalboard Pad
• Online Warranty Registration Information Card
2
7
6
9
11
1 4 5
88
10
3
2
3
What Does This Do?
1. Level Knob - Controls the distortion output level. Turn the knob
clockwise to increase and counter-clockwise to decrease the output
level.
2. DC Adapter Jack - Connect (an optional) Harman PS200R
power supply to this jack. Use the proper supply for your area’s
mains line voltage.
3. Low Knob - Controls the level of low frequency (bass) boost/cut.
Turn the knob clockwise to increase and counter-clockwise to
decrease the bass level.
4. High Knob - Controls the level of high frequency (treble) boost/
cut.Turn this knob clockwise to increase and counter-clockwise to
decrease the treble level.
5. Gain Knob - Controls the overall distortion gain. Turn the knob
clockwise to increase and counter-clockwise to decrease the
amount of distortion gain.
4
6. Voicing Switch - This switches between the Distortion’s two
voicings. Crunch provides a classic balanced distortion. Saturated
features an extra gain stage for maximum sustain distortion making
it ideal for solos.
7. Input - Connect your instrument or the output of another pedal
to this jack.This jack enables battery power to the pedal when con-
nected.To prolong battery life, disconnect the cable from the Input
jack when not in use. If the optional Harman PS200R power supply
is used, cables can remain connected.
8. Foot Switch Release Pins - These two pins are spring loaded
hinges that hold the Foot Switch in place. See page 7 for informa-
tion on accessing and changing the battery.
9. Indicator LED - Lights when the effect is turned on.When bat-
tery power is low (approximately 15 minutes before it dies), the
Indicator LED begins to dim giving you advanced warning that very
shortly you will need to replace the battery.
5
10. Foot Switch - Turns the effect on and off.
11. Output - Connect this output to the input of your amplifier or the
input of another pedal.
Note: Use unbalanced mono instrument cables only.
6
Amplifier Setup
PS200R
(optional)
or
Tabla de contenidos
