Harbor Freight Tools 90034 Guía de referencia rápida
ASSEMBLY & OPERATING INSTRUCTIONS
®
3
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web Site at www.harborfreight.com
90034
30” HARLEY (RED)
TOY ROCKER
THANKYOU for choosing a HARBOR FREIGHTTOOLS product. For future reference, please complete the
owner’s record below:
Model______________ Serial No._____________ Purchase Date_______________
SAVE THE RECEIPT, WARRANTY ANDTHESE INSTRUCTIONS. It is important that you read the entire
manual to become familiar with the unit BEFORE you begin assembly.
Technical Specifications
Construction: Pine Wood
For ages: 3-8
Maximum Weight: 100 LBS.
Overall Dimensions: 35-1/5” L x 11”W x 20-1/2” H
Safety Warnings and Precautions
WARNING:When using product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Do not use this product in damp or wet locations. Don’t
expose to rain. Keep work area well lighted.
3. Store idle equipment. When not in use, products must be stored in a dry location to inhibit
rust.
4. Check for damaged parts. Before using any product, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended function.
Check for any broken or damaged parts and any other conditions that may affect its operation.
Replace or repair damaged or worn parts immediately.
5. Replacement parts and accessories. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
6. Use eye protection. Always wear ANSI approved impact safety goggles when assembling this
product.
7.Always check hardware and assembled parts after assembling. Use in an area that is
flat and level. All connections should be tight and hardware tightened.
8. All assembly should be done by an adult.
9. TheToy Rocker should be played with in the presence of an adult. The Toy Rocker is for
indoor use. Use on a padded surface, like a carpet.
10.This product contains small parts and therefore represents a choking hazard.
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
#90034 Page 2
Assembly
Your Toy Rocker will require complete assembly prior to use. It is important that you read the entire
manual to become familiar with the product BEFORE you use the Toy Rocker. Before assembling
the Toy Rocker be sure that you have all parts described in the Parts List and Assemby Diagram
located on the last page of this manual.
Step 1) Attach the two (2) Rocker Slats (#1) together with Cross Piece (#2). Place Rocker
Slats (#1) parallel to each other and set Cross Pieces (#2) down in-between them at
each end. Insert 2 Hex Bolts (A) into the holes at each end of the Rocker Slats and
into holes in Cross Piece (#2). Insert Nut (B) down into Cross Piece (#2). Turn the
Nut (B) clockwise which will pull in Hex Bolt (A) and tighten the Rockers Slats (#1) to
the Cross Pieces (#2)-refer to Figure 1.
#90034 Page 3
Step 2) Next, attach the Rocker Slats (#1) and Cross Pieces (#2) to the Body (#4). Insert the
Connecting Plate (#3) so that the dowel on the Connecting Plate (#3) goes into the
middle hole on the Cross Piece and up into the Body (#4)-see Figure 2.
Rocker Slat (#1) Cross Piece (#2)
Two Hex Bolts (A)
Two Hex Bolts (A)
Nut (B)
Figure 1-Rocker Slats with Cross Pieces
Connecting Plate (#3)
Rocker Slat (#1)
Cross Piece (#2)
Figure 2-Attaching Connecting Plate to Body
Step 3) Secure the Connecting Plate (#3) to the assembly by inserting the two-sided Bolt (E)
through Body (#4), Connecting Plate (#3) and out other side of Body (#4). On each
end of Two-Sided Bolt (E), slide on Big Washer (J), Spring Washer (K) and tighten on
Nut (I).
Step 4) Fully secure the Connecting Plate (#3) to each Cross Piece (#2) by inserting the
two (2) Hex Bolts (D) down into the Cross Piece. Slide on Medium Spring
Washer (L), Washer (G) and tighten on Nylon Nut (H).
Step 5) Insert two (2) Hex Bolts (C) down through the Seat Bottom (#5).
Step 6) Insert the Handlebar (#6) through the top holes in the forks. Slide one Washer (M)
onto each Screw (F) and thread into the hole in front of fork and into the Handlebar
(#6) to secure in place-see Figure 3.
Handlebar (#6)
Screws (F) with
Washers (M)
Figure 3-Handlebar to Body
#90034 Page 4
Step 6) If decals are not attached, apply decals as shown on manual cover. Peel off decal
from paper and attach to Toy Rocker.
Unpacking
UNPACK AND CHECK CONTENTS
When unpacking your Harley 30”Toy Rocker, check to make sure the following parts are included. If any parts
are missing or broken, please call HARBOR FREIGHTTOOLS at 1-800-444-3353.
Part # Description Quantity
1 Rocker Slats 2
2 Cross Piece 2
3 Connecting Plate 2
4 Body 1
5 Seat Bottom 1
6 Handlebar 1
Part # Description Quantity Part # Description Quantity
A Hex Bolt 2 H Nylon Nut 4
B Nut 8 I Nut 4
C Hex Bolt 2 J Big Washer 4
D Hex Bolt 4 K Spring Washer 4
E Bolt 2 L Medium Spring Washer 4
Hardware
F Screw 2 M Washer 2
G Washer 4 N Wrench 2
#90034 Page 5
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHERTHE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KINDTO THE BUYERTHAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRSTOTHE PRODUCT ORTHAT HE OR SHE IS
QUALIFIEDTO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER.THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTSTHERETO.
O Allen Wrench 1
Tabla de contenidos
Otros manuales de Juguete de Harbor Freight Tools
Harbor Freight Tools
Harbor Freight Tools 95641 Manual de lista de piezas
Harbor Freight Tools
Harbor Freight Tools 57293 Instrucciones de montaje
Harbor Freight Tools
Harbor Freight Tools 56513 Instrucciones de montaje
Harbor Freight Tools
Harbor Freight Tools 3514 Manual de usuario
Harbor Freight Tools
Harbor Freight Tools 62578 Instrucciones de montaje
Harbor Freight Tools
Harbor Freight Tools 91192 Manual de usuario
Harbor Freight Tools
Harbor Freight Tools 94737 Manual de usuario
Harbor Freight Tools
Harbor Freight Tools 94774 Manual de instalación
Harbor Freight Tools
Harbor Freight Tools 94840 Manual de instalación
Harbor Freight Tools
Harbor Freight Tools U.S. GENERAL Junior 56515 Instrucciones de montaje
Harbor Freight Tools
Harbor Freight Tools 68752 Manual de usuario
Harbor Freight Tools
Harbor Freight Tools 95641 Manual de lista de piezas
Harbor Freight Tools
Harbor Freight Tools 92304 Guía de referencia rápida
Harbor Freight Tools
Harbor Freight Tools River Boat Manual de usuario
Harbor Freight Tools
Harbor Freight Tools 95125 Manual de lista de piezas
Harbor Freight Tools
Harbor Freight Tools 91131 Manual de usuario
Harbor Freight Tools
Harbor Freight Tools AIR PIXIE HELICOPTER Manual de instalación
Harbor Freight Tools
Harbor Freight Tools BUCK HORN WAGON WOODEN MODEL 9141 Manual de usuario
Harbor Freight Tools
Harbor Freight Tools 90033 Guía de referencia rápida
Harbor Freight Tools
Harbor Freight Tools Lightning Airplane with Charger 42619 Manual de instalación
