Harbor Breeze 00892 Manual de usuario

Español p. 19

CLASSIC STYLE

CEILING FAN

ITEM #0076253

MODEL #00892

Serial Number Purchase Date

Harbor Breeze®is a registered trademark of LF,

Questions, problems, missing parts? Before returning to your retailer,

call our customer service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST,

Monday - Thursday, 8 a.m. - 5 p.m., EST Friday

PB18424

ATTACH YOUR RECEIPT HERE

UL MODEL #CSS36

TABLE OF CONTENTS

Package Contents...................................................................................................... 3

Hardware Contents..................................................................................................... 4

Preparation ............................................................................................................... 4

Safety Information....................................................................................................... 5

Assembly Instructions ............................................................................................... 6

Downrod style fan mounting ...................................................................................... 7

Closemount style fan mounting ................................................................................. 8

Operating Instructions ............................................................................................... 16

Care and Maintenance ............................................................................................. 17

Troubleshooting......................................................................................................... 17

Warranty..................................................................................................................................18

Replacement Parts List ............................................................................................. 18

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY

A Mounting Bracket (preassembled to canopy (B)) 1

B Canopy 1

C Canopy Cover (preassembled to canopy (B)) 1

DDownrod Assembly 1

E Blade Bracket 5

F Blade 5

G Motor Housing 1

H Switch Housing (preassembled to motor housing (G)) 1

I Switch Housing Cover 1

J Light Kit 1

K Glass Bowl 1

L Bowl Cap (preassembled to light kit (J)) 1

M Finial (preassembled to light kit (J)) 1

N Bulb 2

O Rubber Motor Stopper with Screw 3

)

HARDWARE CONTENTS SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, operate or install the product.

• When using an existing outlet box, be sure the box is securely attached to the building structure and can

support the full weight of the fan, so to avoid potential serious injury or death.

• All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999” and local electrical

codes. Electrical installation should be performed by a qualied licensed electrician.

• DO NOT use bulbs with wattage greater than the maximum value stated on the xture and in this manual.

Using a higher wattage bulb than specied will increase xture temperature and cause risk of re.

• Disconnect the electrical supply circuit to the fan before installing kit.

• Electrical diagrams are for reference only.

• The net weight of this fan including the light kit is: 13.27 lbs.

WARNING

• ELECTRIC SHOCK HAZARD - To reduce the risk of electric shock, do not use this fan with any solid-state

speed control device.

• ELECTRIC SHOCK HAZARD - To reduce the risk of electric shock, make sure the electricity has been turned

off at the circuit breaker or fuse box before beginning installation.

• PERSONAL INJURY HAZARD - To reduce the risk of personal injury, do not bend the blade brackets when

installing the brackets, balancing the blades, or cleaning the fan. DO NOT insert foreign objects in between

the rotating fan blades.

• FIRE, ELECTRIC SHOCK OR PERSONAL INJURY HAZARD - To reduce the risk of re, electric shock,

or personal injury, mount to an outlet box marked “ACCEPTABLE FOR FAN SUPPORT OF 35 lbs OR

LESS” and use the mounting screws provided with the outlet box. Most outlet boxes commonly used for

the support of lighting xtures are not acceptable for fan support and may need to be replaced. Consult a

qualied licensed electrician if in doubt.

• PERSONAL INJURY HAZARD - To reduce the risk of injury to persons, install fan so the blades are 7 ft.

above the oor.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts

with package contents list and hardware contents list. If any part is missing or damaged,

do not attempt to assemble the product.

Estimated Assembly Time: 45 minutes.

Tools Required for Assembly (not included): Phillips screwdriver, step ladder, electrical

tape, pliers, wire cutters, wire strippers.

Helpful Tools (not included): Electrical circuit tester.

Wire Connector

Qty. 4

Blade Screw

Qty. 16

Light Pull Chain

Extension

Qty. 1

Fan Pull Chain

Extension

Qty. 1

Rubber Gasket

Qty. 1

(not to scale)

ASSEMBLY INSTRUCTIONS

1. Determine mounting method to use.

A - Downrod Mount (standard or angled ceiling)

B - Closemount (normal ceiling only)

IMPORTANT: lf using the angle mount, check

to make sure the ceiling angle is not steeper

than 20°.

2. Remove the rubber motor stoppers (O) from

the bottom of the fan motor assembly (G)

by loosening the three screws. Discard the

rubber motor stopper and screws.

3. Remove the mounting bracket (A) from the

canopy (B) by loosening the four screws

on the top of the canopy (B). Remove the

two non-slotted screws and save, then

loosen the slotted screws. This will enable

you to remove the mounting bracket (A).

4. Install the mounting bracket (A) to the outlet box

(not included), sliding the mounting bracket (A)

over the two outlet box screws (not included).

Securely tighten the two outlet box screws.

IMPORTANT: If using the angle mount, make

sure open end of mounting bracket (A) is

installed facing the ceiling.

Outlet

box

clip

Loosen but

do not remove

Remove

and save

ASSEMBLY INSTRUCTIONS

DOWNROD STYLE FAN MOUNTING

1. Remove pin and clip from downrod assembly

(D) and save.

2. Insert downrod assembly (D) through

canopy (B), canopy cover (C). Thread

wires from the motor housing assembly (G)

through downrod (D).

Follow mounting instructions for “Downrod

Style Fan Mounting” or “Closemount Style

Fan Mounting”, depending on mounting

method (A or B) chosen in step 1 on previous

page.

DOWNROD STYLE FAN MOUNTING

3. Loosen the two set screws from the yoke on

the top of the motor housing (G). Slip downrod

assembly (D) into housing yoke, aligning holes

in downrod assembly (D) and yoke. Insert the

pin through yoke and downrod assembly (D).

Insert clip into pin until it snaps into place.

Tighten set screws.

4. Install hanger ball on the top of downrod (D)

into mounting bracket (A) opening. Rotate fan

until slot on hanger ball engages the tab on

the mounting bracket (A).

1. Remove the canopy cover (C) from the

bottom of the canopy (B).

clippin set

screw

slot

tab

WARNING: Be careful when aligning the tab

to the slot! If not fully engaged, there is a

possibility of fan falling, which may result in

serious injury or death.

CLOSEMOUNT STYLE FAN MOUNTING

2. Remove three of the six screws and

lockwashers (every other one) securing

the motor collar to the top of the fan motor

housing (G).

3. Place the rubber gasket (EE) over the

remaining screws. Pull wires through hole in

canopy (B), and attach canopy (B) to motor

housing (G). Align the mounting holes with

the holes in the motor and fasten using the

three screws removed in previous step.

Tighten the screws securely.

4. Hang the fan on the hook on the mounting

bracket (A) using one of the non-slotted

holes in the canopy (B).

hook

You may now proceed to the WIRING section

on page 10.

Hardware Used

Rubber gasket x 1

1110

WIRING

2. To connect wires, twist wire ends together

and screw wire with wire connectors (AA) in a

clockwise direction. Tape the wire connectors

(AA) and wires together with electrical tape (not

included). Be sure no bare wire or wire strands

are visible after making connection.

1. Remove the fan from the hook on the

mounting bracket (A). Align the locking slots

of the canopy (B) with the two screws in the

mounting bracket (A). Push up to engage

the slots and turn clockwise to lock in place.

Immediately tighten the two screws rmly.

outlet

box

screws

hook

locking

slots A

Place GREEN and WHITE connections on

opposite side of box from the BLACK and

BLUE connections. The splices should be

turned upward and pushed carefully up into

the outlet box.

FINAL INSTALLATION

2. Install the two screws that were removed in

previous step and tighten securely.

3. Directly align the locking slots of the canopy

(B) with the two screws in the mounting

bracket (A). Push up to engage the slots and

turn clockwise to lock in place. Immediately

tighten the two screws rmly. Install the two

screws that were removed in previous step

and tighten securely.

4. Attach a blade (F) to a blade bracket (E)

using the blade screws (DD).

Repeat for remaining blade assemblies.

screw

outlet box

screw

outlet box

Hardware Used

Blade Screw x 16

1. Connect the BLACK and BLUE wires from

the fan to the house BLACK wire. Connect

the WHITE wire from fan to the house WHITE

wire. Connect all GROUNDED (GREEN)

wires together from fan to the house GREEN/

GROUND wire.

NOTE: BLACK wire is hot power for fan.

BLUE wire is hot power for light kit. WHITE

wire is common for fan and light kit. GREEN

wire is ground wire. If house wires are

different colors than referred to above, stop

immediately. Consult a licensed electrician to

determine proper wiring.

Hardware Used

Wire Connector x 4

If you installed the fan with “Closemount Style

Fan Mounting”, continue to Steps 1 and 2. If

you installed the fan with “Downrod Style Fan

Mounting”, skip to Step 3.

Grounded/Green

Black

White

Grounded/

Green

Black

Blue

White

outlet box

blue

black

white

green white

Green/

Grounded

black

Supply Circuit

speed

switch

You may now proceed to Step 4.

1312

FINAL INSTALLATION

6. Remove the three screws from the switch

housing cover (I).

7. Attach the switch housing cover (I) to the switch

housing (H). Align holes in switch housing

cover (I) with holes on outer edge of the switch

housing (H). (Note: The wide gap in the edge

of the switch housing cover (I) should align

with reverse switch on the switch housing

(H).) Re-insert screws and secure all screws.

Add fan pull chain extension (BB). If using fan

WITHOUT the light kit, assembly is complete.

IBB

FINAL INSTALLATION

8. Remove the plug from the center hole in the

switch housing cover (I).

9. Remove the hex nut from the light kit (J).

10. Insert the black and white wires from the

light kit (J) through the center hole in the

switch housing cover (I). Hold wires taut

while installing switch housing cover (I) to

prevent the wire from twisting. Tighten the

light kit (J) onto the switch housing cover (I).

Install the hex nut removed in Step 9.

plug

hex nut

5. Fasten the blade bracket (E) to the motor by

inserting the alignment post into the slot on the

bottom of the motor housing (G) and tightening

the blade bracket screws with washers.

Please note that the blade bracket screws with

washers are pre-installed into the blade bracket

(E). Repeat the step for the remaining blade

brackets (E).

screw with

washer

alignment

post

slot

If you wish to use the fan WITHOUT the light

kit, continue to Step 7.

If you wish to use the fan WITH light kit, skip to

Step 8.

Hardware Used

Fan pull chain extension x 1

FINAL INSTALLATION

12. Attach the switch housing cover (I) to the

switch housing (H). Align holes in switch

housing cover (I) with holes on outer edge

of the switch housing (H). (Note: Make sure

the notch in the edge of the switch housing

cover (I) clears the reversing switch in the

switch cup of the fan-motor assembly (G)).

Re-insert screws and secure all screws.

13. Install bulbs (N) into sockets.

NOTE: This fan has an energy-saving wattage

limiter included. If you replace the candelabra-

base bulbs with over 190 watts, the light will

automatically turn off. Please ensure the bulb

wattage is always below 190 watts.

FINAL INSTALLATION

14. Remove the rubber washer, hex nut, bowl

cap (L) and nial (M) from the light kit (J).

15. Place glass bowl (K) on pipe until ush

against metal disk. Thread the fan pull chain

through the side hole of the glass bowl (K),

making sure pull chain hangs clear and is

not tangled in the light kit (J) socket. Thread

light kit pull chain through the center hole of

the glass bowl (K). Place rubber washer and

hex nut removed in Step 14 onto the pipe

and tighten securely. Pass the fan pull chain

through the side hole of the bowl cap (L).

Then place the bowl cap (L) and nial (M)

over the pipe and tighten securely. Attach the

fan pull chain extension (BB) and light kit pull

chain extension (CC).

NOTE: The side hole of the glass bowl (K),

the side hole of the bowl cap (L) and the

three-speed adjustable switch on the switch

housing (H) should be in alignment; if not, the

fan pull chain will be stuck and the fan won’t

work.

rubber washer

hex nut

rubber washer

hex nut

11. Connect the white wire from the light kit (J)

to the white wire from the switch housing (H).

Connect the black wire from the light kit (J)

to the blue wire from the switch housing (H).

Make sure the wire connectors are secure.

WARNING: To avoid possible re or shock,

the connectors should not be removed unless

a light kit will be immediately installed and

power should be turned off prior to removal of

the light kit.

blue

black white

1514

Hardware Used

Fan pull chain extensions x 1

Light pull chain extensions x 1

OPERATING INSTRUCTIONS

1716

TROUBLESHOOTING

CARE AND MAINTENANCE

• To reduce the risk of re, electric shock or injury to persons, care and maintain this fan.

• Important: Shut off main power supply before beginning any maintenance.

• Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or

lightly dampened cloth will be suitable for most cleaning.

• Clean fan housing with only a soft brush or lint-free cloth to avoid scratching the nish.

Clean blades with a lint-free cloth. You may occasionally apply a light coat of furniture

polish to blades for added protection.

• At least twice a year, tighten all screws and lower canopy to check mounting bracket

screws and downrod assembly.

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

Fan does not move. 1. Chain switch is “off”.

2. Faulty wire

connection.

3. Reverse switch not

engaged.

1. Pull chain switch.

2. Turn power off. Loosen

canopy, check all connections.

3. Push switch rmly either way.

Noisy operation. 1. Blades are loose.

2. Cracked blade.

3. Unapproved speed

control.

1. Tighten all blade screws.

2. Replace blades (call customer

service).

3. Replace with an approved

speed control device.

Excessive wobbling. 1. The blades are loose.

2. Blade brackets

incorrectly attached.

3. The fan is not

securely mounted.

4. Fan too close to

vaulted ceiling.

1. Tighten all blade screws.

2. Reinstall blade brackets.

3. Turn power off. Carefully

loosen the canopy and

remount securely.

4. Lower fan or move it to

another location.

1. The fan pull chain is for motor speed control: High, Medium, Low and Off. Pull the chain

once for each position.

2. The light pull chain controls the light xture either ON or OFF with each pull of the chain.

PULL CHAIN:

REVERSE SWITCH:

When the season changes

,you may want to change the direction the fan blades spin. To

switch between clockwise and counterclockwise rotation, ip the fan reversal switch.

NOTE: Wait for fan to stop before reversing switch.

A. In cooler weather, clockwise rotation

creates an upward airow, which

moves hot air from the ceiling into the

room. Push the switch UP and see a

Snowake icon.

B. In warmer weather, counterclockwise

rotation creates downward airow,

which cools the air. Push the switch

DOWN and see a Sun icon

Snowflake

icon

Sun

icon

WARRANTY

REPLACEMENT PARTS LIST

Printed in China

For replacement parts, call our customer service department at 1-800-643-0067,

8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.

The manufacturer warrants this fan to be free from defects in workmanship and material present at

time of shipment from the factory for lifetime limited from the date of purchase. This warranty applies

only to the original purchaser. The manufacturer agrees to correct such defect at no charge or at our

option replace the ceiling fan with a comparable or superior model.

To obtain warranty service, present a copy of your sales receipt as proof of purchase. All cost of

removal and reinstallation are the expressed responsibility of the purchaser. Any damage to the

ceiling fan by accident, misuse, or improper installation, or by afxing accessories not produced by

the manufacturer of the fan, are at the purchaser’s own responsibility. The manufacturer assumes

no responsibility whatsoever for fan installation during the lifetime limited warranty. Any service

performed by an unauthorized person will render the warranty invalid.

Due to varying climatic conditions, this warranty does not cover changes in brass nish, rusting,

pitting, tarnishing, corroding, or peeling. Brass nish fans maintain their beauty when protected from

varying weather conditions. Any glass provided with this fan is not covered by this warranty. Any

replacement of defective parts for the ceiling fan must be reported within the rst year from the date

of purchase. For the balance of the warranty, call our customer service department at 1-800-643-

0067 for return authorization and shipping instructions so that we may repair or replace the ceiling

fan. Any fan or parts returned improperly packaged is the sole responsibility of the purchaser. There

is no further expressed warranty. The manufacturer disclaims any and all implied warranties.

The duration of any implied warranty which can not be disclaimed is limited to the lifetime limited

period as specied in our warranty. The manufacturer shall not be liable for incidental, consequential

or special damages arising at or in connection with product use or performance except as may

otherwise be accorded by law. This warranty gives you specic legal rights an you also have other

rights which may vary from state to state. This warranty supersedes all prior warranties.

Note: A small amount of “wobble” is normal and should not be considered a defect.

PART DESCRIPTION PART #

E Blade Bracket 104000-0411ZW

F Blade 108001-6082AO

I Switch housing cover 105500-0043ZW

J Light Kit 105000-0906ZW

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Admirador de Harbor Breeze

Harbor Breeze

Harbor Breeze HTD21011 Manual de usuario

Harbor Breeze

Harbor Breeze 42612 Manual de usuario

Harbor Breeze

Harbor Breeze BOLTZ 42300 Manual de usuario

Harbor Breeze

Harbor Breeze RLG52NWZ5L Manual de usuario

Harbor Breeze

Harbor Breeze RC103L Manual de usuario

Harbor Breeze

Harbor Breeze EUK60MBK10LR Manual de usuario

Harbor Breeze

Harbor Breeze BELCARRA CE-JP13BNK6RC Manual de usuario

Harbor Breeze

Harbor Breeze 873 Manual de usuario

Harbor Breeze

Harbor Breeze 00881 Manual de usuario

Harbor Breeze

Harbor Breeze Bath Ventilator with Light Manual de usuario

Harbor Breeze

Harbor Breeze ARMORY 40087 Manual de usuario

Harbor Breeze

Harbor Breeze COGDELL COG60BNK7LR Manual de usuario

Harbor Breeze

Harbor Breeze CLASSIC STYLE 00819 Manual de usuario

Harbor Breeze

Harbor Breeze 41169 Manual de usuario

Harbor Breeze

Harbor Breeze L0982 Manual de usuario

Harbor Breeze

Harbor Breeze MARICOPA LP8013LAZ Manual de usuario

Harbor Breeze

Harbor Breeze ARMITAGE CC52WW5C1 Manual de usuario

Harbor Breeze

Harbor Breeze CHESHIRE II CSD52FBZ5C4S Manual de usuario

Harbor Breeze

Harbor Breeze PACIFIC GROVE 40101 Manual de usuario

Harbor Breeze

Harbor Breeze OCEANSIDE Manual de usuario

Harbor Breeze

Harbor Breeze ELEVATION LP8006LBN Manual de usuario

Harbor Breeze

Harbor Breeze URBANIA Manual de usuario

Harbor Breeze

Harbor Breeze MERRIMACK II 41125 Manual de usuario

Harbor Breeze

Harbor Breeze LP8071LBN Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje