Hanskamp MultiFrame Manual de usuario
MultiFrame
EN
Installaon instrucon
Arkelnumber: 010-243-000
Date: March 2020
Version 1.6 - Translaon of original instrucons
In parlour feeding
075-000-000
Doenchem,
The Netherlands
www.hanskamp.nl/en
2 - 8
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulFrame
EN 075-000-000
Montage MulFrame
1. Decide for mounng the MulFrame, where the MulFrame should
hang. The distance between the MulFrames is dependent on the
type of milking parlour. The posion measurements are, therefor, to
nd in the drawing of the milking parlour.
2. When the distance is determined, the holes can be drilled according
to the dimensions as shown in the drawing.
3. Now install the MulFrame on the wall. (Mounng material not in-
cluded).
X ≈ 2000mm - 2300mm
X1 = depending on the size of the animal, measure this.
Mounng Feedtrough
1. Install the feedtrough in the MulFrame. The feedtrough is easy to place in the
frame by sliding it obliquely below the 2 vercal tubes which are welded to the
ring. When the edge of the feedtrough is placed under the vercal tubes, the
feedtrough can be placed on the ring. The feedtrough
is now secured on one side.
2. Secure now the other side of the feedtrough with sup-
plied mounng material as shown in Figure 3.
1
2
34
007-522-000 007-522-001
There are two types of feedthroughs available. The perfora-
ted feedtrough (art.nr.: 007-522-000) and the tradional
feedtrough with one hole. (art.nr.: 007-522-001).
XX1
3 - 8
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulFrame
EN 075-000-000
Mounng PipeFeeder
1. Mount the PipeFeeder to the MulFrame with included mounng material
as shown in Figure 5.
2. Make sure the boom of the PipeFeeder is level with the top of the feed-
trough
3. In order to let the PipeFeeder dosing nicely into the feedtrough, it is desira-
ble to rotate the tube of the PipeFeeder 45° so that the discharging secon
is hung above the feedtrough.
Please note! If the stainless steel tube of the PipeFeeder is rotated with pertaining
to the plasc part make sure that de PipeFeeder is re-adjusted in order to maintain
the an-spill funcon. For adjusng the PipeFeeder see manual 001-847-000
Adjust the PipeFeeder not to the MulFrame by a truss structure or similar. Then
the PipeFeeder can also be mounted on the wall. The distance between the wall
and the PipeFeeder remains unchanged from mounng on the MulFrame. For
example, all PipeFeeders remain perfectly straight line in order to keep the parlour
ght.
MulFrame degree posions
The MulFrame 30° is the complete MulFrame as described above. These will be
delivered without sidefence. 40°, 50° & 60° parlours can be made with a short side
fence (art.nr.: 007-504-000). 70° & 80° parlours can be made with a long side fence
(art.nr.: 007-505-000).
40° & 50° 60° 70° 80°
5
6
007-504-000 007-505-000
4 - 8
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulFrame
EN 075-000-000
Right Le
Aachment; Right / Le
Grounding MulFrame
It is recommended to ground all MulFrames.
To ground, there is a tube lug (art.no.: 001-302-000) provided it could be mount bet-
ween any bolt and nut of the MulFrame.
Maintenance MulFrame
Clean the feedtrough regurlarly and make sure the feedtrough stays
clean. Let the water out of the feedtrough aer cleaning it.
5 - 8
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulFrame
EN 075-000-000
Mounng Reader/Antenna mount (individual stall recognion)
It is possible to mount various types of antennas on the MulFrame.
One suited for DeLaval (art. no. 007-524-000) and one suited for Hanskamp,
Nedap & Fullwood antennas (Art.nr.: 007-525-000) (g. 7).
In gures 8-11 is displayed how to reader mount 007-525-000. mount 007-
524-000 is mounted in the same way.
To shield the antenna cable, a guide tube can be placed (g. 12-14). This is
available at Hanskamp as a set : Art.nr.: 007-530-000 for neck collar tag read-
ers, art.nr.: 007-531-000 for leg tag readers.
7
8910
11
12 13 14
6 - 8
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulFrame
EN 075-000-000
FAQ
Occurring problem Possible cause Soluon
Side fence does not t,
mounng holes do not match
Fence is posioned the wrong way. Turn fence 180° and try again.
No mounng for stand-place
recognion
No antenna mounng plate ordered or
delivered.
Order for Delaval antenne 007-524-
000
Order for Nedap antenna 007-525-
000
List of included amendments in this installaon- and operang instrucon
No. Release date Chapter comments
1.0 01/2016 First edion
1.1 02/2016 Aachment & Arcle structure Arcle names are changed & grounding added
1.2 01/2017 Aachment FAQ added
1.3 01/2018 Mounng Picture PF to low added
1.4 01/2018 Antenna mounng Added antenna mounng instrucons.
1.5 06/2019 Front page, images 1 & 2 Changed to most recent version MulFrame
1.6 03/2020 Pag. 2 and 4 Image added pag. 2, comment added pag. 4
7 - 8
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulFrame
EN 075-000-000
Art.no.: Descripon QTY.
007-501-000 MulFrame right 1
007-502-000 MulFrame le 1
007-504-000 Side fence short 1
007-505-000 Side fence long 1
Art.no.: Descripon QTY
007-522-000 Perforated feedtrough 1
007-522-001 Feedtrough with hole Ø20 1
Art.no.: Descripon QTY
001-037-000 Washer M8 r9.0 a2 DIN440R 2
001-302-000 Tube cable lug M10 4,5mm² 1
001-382-000 Minigrip packaging sachets 100x150mm 1
001-531-000 Bolt M10x60 DIN931 a2 4
001-532-000 Washer M10 a2 DIN125/ A1 8
001-707-001 Washer M10x34x3 DIN440 8.8ev 2
001-707-002 Curved washer M10x34x3 DIN440 8.8ev 6
001-741-000 Bolt M8x55 a2 DIN933 2
001-769-000 Sloed retaining nut M8 a2 DIN985 coat 2
001-774-000 Washer M8 DIN 9021 a2 2
001-805-000 Bolt M10x70 DIN 931 8.8ev 2
001-857-000 Sloed retaining M10 a2 DIN 985 coat GL 4
001-866-000 Sloed retaining moer M10 DIN 985 8.8ev 4
011-124-000 Bolt M10x105 DIN931 8.8ev 2
MulFrame parts
Type feedtrough
007-506-000 Mounng material
Art.no.: Descripon QTY
007-524-000 Mount for Reader 3mm incl. (DeLaval) 1
007-525-000 Mount for Antenne 3mm AISI304 (Hanskamp, Nedap, Fullwood) 1
007-530-000 Cable guide tube set (Neck collar antenna) 1
007-531-000 Cable guide tube set (Leg tag antenna) 1
Antenna mount incl. mounng material
8 - 8
Hanskamp AgroTech B.V. (the Netherlands) www.hanskamp.nl/en
MulFrame
EN 075-000-000
Hanskamp AgroTech B.V.
Broekstraat 17
7009 ZB Doenchem
Nederland
Tel: +31 (0)314 - 393 797
Fax: +31 (0)314 - 393 826
Visit us on:
Este manual sirve para los siguientes modelos
1
Otros manuales de Maquinaria agrícola de Hanskamp
Hanskamp
Hanskamp SpiderServer Manual de usuario
Hanskamp
Hanskamp FeedStation 42000 Guía del usuario
Hanskamp
Hanskamp PipeFeeder HighSpeed Guía del usuario
Hanskamp
Hanskamp MultiFrame 007-501-000 Manual de usuario
Hanskamp
Hanskamp PipeFeeder HighSpeed Guía del usuario
Hanskamp
Hanskamp PipeFeeder Dump Manual de usuario
Hanskamp
Hanskamp PowerSpray Manual de usuario
Hanskamp
Hanskamp MultiDos 035-000-000 Series Manual de usuario
Hanskamp
Hanskamp Spider Manual de usuario
Hanskamp
Hanskamp PipeFeeder Guía del usuario
Manuales populares de Maquinaria agrícola de otras marcas
GSi
GSi PNEG-2314 Manual de usuario
Checchi & Magli
Checchi & Magli TEXDRIVE Manual de usuario
Amazone
Amazone Cenius 4003-2TX Manual de usuario
MASSEY FERGUSON
MASSEY FERGUSON MF 9313S Manual de usuario
Cima
Cima BLITZ Instrucciones de funcionamiento y mantenimiento
Amazone
Amazone CombiDisc 3000 Instrucciones de instalación
