CONNECTING THE UNIT TO POWER
Plug one end of the AC/DC adaptor into the DC-In jack, and then plug the other end into AC
wall outlet Before switching on the unit, make sure that the voltage of your electricity supply is
the same as that indicated on the rating plate
CONNECTING THE LOUDSPEAKERS
Connect the cables of the two loudspeakers to the corresponding input (R) for the right speaker
and input (L) for the left speaker, located at the rear side of the unit
Warning: Connect the loudspeakers before powering the unit The unit may not work
properly or get damaged if you use speakers different than the ones supplied with the unit
SETTING THE TIME
Before starting to set the time, make sure that the unit is in POWER OFF Mode
1 Press and hold the FUNC/CL ADJ button for 1-2 seconds, (you can also press and hold the
CL ADJ button for 1-2 second on the remote control), the hour digit in the display will start
flashing
2 Use the SKIP+/TUNE+ or SKIP−/TUNE− button to adjust the hour
3 When the correct hour is selected, press the FUNC/CL ADJ button again, the minute digit
in the display will start flashing
4 Use the SKIP+/TUNE+ or SKIP−/TUNE− button to adjust the minute
5 When the correct time is selected, press the FUNC/CL ADJ button to store the time in the
memory
SETTING THE ALARM TIME
Before starting to set the alarm time, make sure that the unit is in POWER OFF mode
1 Press the MEM−/AL1 or MEM+/AL2 button on the unit once and the AL1 or AL2 icon will
appear in the display
2 Press the FUNC/CL ADJ button to select the alarm wake up source The options are
buzzer, Radio or CD
3 Press the VOL+ or the VOL− to adjust the wake up sound level
4 Press and hold the MEM−/AL1 or MEM+/AL2 button on the unit for 1-2 seconds, the alarm
hour digit will begin flashing
5 Use the SKIP+/TUNE+ or SKIP−/TUNE− button on the unit to adjust the alarm hour
6 When the desired alarm hour is selected, press the MEM−/AL1 or MEM+/AL2 button again,
the alarm minute digit will begin flashing
7 Use the SKIP+/TUNE+ or SKIP−/TUNE− button on the unit to adjust the alarm minute
8 When the desired alarm time is selected, press the MEM−/AL1 or MEM+/AL2 button again
to confirm
TURN OFF THE ALARM
When the alarm activate, press the POWER/AL OFF button to turn off the alarm
SNOOZE FUNCTION
1 Whenever the alarm activate, it can be temporarily suspended for a short period of 9
minutes by pressing the SNOOZE button
2 The alarm will automatically activate again after the 9 minutes SNOOZE period has ended
3 This procedure can be repeated for up to approximately one hour
- 3 -
RADIO OPERATION
1 Press the POWER/AL OFF button (or press the POWER button on the remote) to turn on
the unit
2 Press the FUNC /CL ADJ button (or press the FUNC button on the remote control) to
select the FM RADIO mode
3 Press and hold the SKIP+/TUNE+ or SKIP−/TUNE− button on the unit for approx 1
second, it will start to search the next available radio station in the direction of the search
The search operation simply finds stations with strong signals Stations with weak signal
can only be tuned in manually
4 Use the P-MODE/MONO button (or use the MONO button on the remote) to select stereo
or mono broadcasting
5 Press VOL+ or VOL− button to adjust the volume to the desired listening level
SAVING RADIO STATIONS IN THE MEMORY
Note : If you use this unit in the first time, or after plug off the AC/DC adaptor from a wall outlet,
the unit memory number will be starting from P01
1 Tune to the desired stations
2 Press the PROG/MEM button (or press the MEM button on the remote control), the display
will show the next memory station number and flash continuously
3 Press the SKIP+/TUNE+ or SKIP−/TUNE− button on the unit to select memory number
(you can also use the M+ or M− on the remote control), then press PROG/MEM button on
the unit or the MEM button on the remote control again to store the station into the memory
4 Repeat step 1 to 3 to store more radio stations in the memory
5 Up to maximum 20 radio stations can be stored in the memory
TO SELECT A STORED RADIO STATION IN THE MEMORY
Use the MEM+/AL2 or MEM−/AL1 button on the unit or the M+ or M− button on the remote
control to select the stored radio station
Press the MEM+/AL2 button on the unit or the M+ button on the remote control to skip up to the
next stored station in the memory
Press the MEM−/AL1 button on the unit or the M− button on the remote control to go back to
the previous stored station in the memory
CD OPERATION
1 Press the POWER/AL OFF button to turn on the unit
2 Press the FUNC/CL ADJ button to select the CD mode
3 Insert a CD disc in the CD compartment and close the CD door, the unit will start reading
the disc, it will play the first track of the entire disc after reading
4 Press VOL+ or VOL− button to adjust the volume to the desired listening level
5 During playing, press the PLAY/PAUSE button to temporarily pause playing To resume,
press the PLAY/PAUSE button again
6 To stop playing, press the STOP button
- 4 -
