Hanil Component wR Manual de usuario

Quick Guide Component wR

Cat. No. : CP-wR

Display & Control Panel

PULSE

VIEW

SETTINGS

Start Stop Lid Open

Max. RPM : 4,500 rpm

Max. RCF : 5,096 xg

Display Screen

Status of RPM / RCF / Time /

Temperature / Rotor ID /

ACC / DEC / Program

Setting Speed

Press once : Setting RPM

Press twice : Setting RCF

Setting Time

Up < 100 hr

Continuous run (00:00)

View Settings

Verifying the setting

parameters during

centrifugation

Setting Temperature

Setting temperature ( -20℃ ~ 40℃)

Setting temp. limit

Pulse

Program Save / Call

Saving a program

(up to 100)

Calling up a program

Setting the Rotor ID manually

Enter the rotor ID. manually, when

rotor id is not identified automatically

Press the

Pulse button

Enter the desired speed

(See ‘Setting Run Parameters’)

Saving / Calling Up a Program

Press a parameter

to be changed

Press the

Enter button

Enter the desired values

on the keypad

Enter the desired

program number on

the keypad

Press the

Save or call button

Setting Run Parameters

(RPM / RCF / Time / Temperature / ACC / DEC)

Press the

Enter button

Press the

Temp. limit button

Press the

Enter button

Temperature range that stops operation when the temperature

is lower or higher than the set temperature.

Enter the desired

temperature range

on the keypad

Setting Temp. Limit

Pulse

After reaching the set

speed, the centrifugation

is decelated and stopped

Setting ACC / DEC Rate

ACC (0 ~ 9 steps, Max.9)

DEC (0 ~ 9 steps, Natural DEC.0)

Serial No. Installation Date

2 31

5 64

8 97

Connect the device to voltage

sources, which correspond to the

electrical requirements on the label

attached to the device.

Check the wall outlet is earth-

grounded, surge-protected and

can supply enough power.

Connect the power cable to the

distribution box, or install the plug

and socket that are packed with

the device.

Switch off the device after use.

Unplug the power plug before

cleaning or unused for a long

period of time.

Check the Line Voltage Grounded Outlet Power Connection Switch Off the Device

Quick Guide Component wR

Cat. No. : CP-wR

WS750-6 6 x 750 mL / Max. 4.5k

30 cm

Allow a safety clearance of

30 cm around the centrifuge

during operation and

storage.

Care of Swing-Out

Rotor

Remove Dust Empty the Condensation

Water

Allow a Safety Clearance

of 30 cm

Emergency Lid Open

If the centrifuge lid cannot be opened,

insert the provided T-wrench into the

emergency release hole on the right side

of the device and press it. (Before activat-

ing emergency open, switch off the

device and wait for the rotor to stop.)

Spread the grease lightly

on the bucket where it

contacts the rotor and the

pivot.

Remove any dust from the

ventilation slits on the right

side of the device. Empty the condensation water

regularly by removing the

drain cap on the left side of the

device.

3.0KVA

220~240V 50/60Hz

Maintenance

Electrical Safety

Rotors

Cautions for Use

Before Operation After Operation

Check the rotor, buckets and tubes are free

of scratch and crack before operation.

Check the Accessories for Abnormalities

After relocating the device or loading the rotor,

balance them by using a leveler. If necessary,

level the device by adjusting the ‘Leveling foot’

on the bottom of the device.

Balancing the Centrifuge and Rotor

Load tubes symmetrically into the rotor

with identical amount.

Load Tubes Symmetrically

Place the lid on the wind shield rotor before

centrifugation.

Check the Lid

Wipe up the moisture in the chamber with a

dry cloth after use. Keep the lid open when

not in use.

Clean the chamber and rotor by wiping with

a cloth soaked in mild detergent and dry

completely.

Keep the Chamber Dry

Cleaning

Rev.1

Proudly made by Jiyoung Shim, Hyewon Jeong

Order & Inquiry l +82-2-3472-0727 l [email protected] l www.ihanil.com

Service l +82-2-3452-8966 l [email protected]

Otros manuales de Equipo de laboratorio de Hanil

Hanil

Hanil M15R Manual de usuario

Hanil

Hanil M 13 Manual de usuario

Hanil

Hanil T05R Manual de usuario

Hanil

Hanil M15S Manual de usuario

Hanil

Hanil Smart 15 Plus Manual de usuario

Hanil

Hanil Supra R30 Manual de usuario

Hanil

Hanil Ultra 5.0 Manual de usuario

Hanil

Hanil Fleta 5 Manual de usuario

Hanil

Hanil ARA Smart 6 Manual de usuario

Hanil

Hanil Component R12 Manual de usuario

Hanil

Hanil HyperVAC HVC-2124 Manual de usuario

Hanil

Hanil Supra R30 Manual de usuario

Hanil

Hanil FLETA 4 Manual de usuario

Hanil

Hanil Micro 12 Manual de usuario

Hanil

Hanil T04 Manual de usuario

Hanil

Hanil FLETA 4 Manual de usuario

Hanil

Hanil Smart R17 Manual de usuario

Hanil

Hanil J1250 Manual de usuario

Hanil

Hanil Ultra 5.0 Manual de usuario

Hanil

Hanil SeroSpin II Manual de usuario

Hanil

Hanil Component R6 Manual de usuario

Hanil

Hanil T05R Manual de usuario

Hanil

Hanil Supra R17 Manual de usuario

Hanil

Hanil Fleta 5 Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario