HAMPTON BAY Carrison 499 461 Manual de usuario

Model

499 461

52" CEILING FAN

CARRISON

Model

499 461

52" CEILING FAN

CARRISON

Hampton Bay Lifetime Limited Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material

present at time of shipment from the factory for a lifetime after the date of purchase by the

original purchaser. The retailer also warrants that all other fan parts, excluding any glass or

plexiglass blades, to be free from defects in workmanship and material at the time of

shipment from the factory for a period of one year after the date of purchase by the original

purchaser. We agree to correct such defects without charge or at our option replace with a

comparable or superior model if the product is returned to the retailer. To obtain warranty

service, you must present a copy of the receipt as proof of purchase. All costs of removing

and reinstalling the product are your responsibility. Damage to any part such as by accident

or misuse or improper installation or by affixing any accessories, is not covered by this

warranty. Because of varyingclimatic conditions inthe United States this warranty does not

cover any changesin brass finish, including rusting, pitting, corroding, tarnishing orpeeling.

Brass finishes of this type give their longest useful life when protectedfrom varying weather

conditions. A certain amount of wobble is normal and should not be considered a defect.

Servicing performed by unauthorized persons shallrender the warranty invalid. There is no

other express warranty. The retailer hereby disclaims any and all warranties,

including but not limited to. Those of merchantability and fitness for a particular

purpose to the extent permitted by law. The duration of any implied warranty which

cannot be disclaimedis limited to the time period as specified inthe express warranty. Some

states do not allow limitation on how long an implied warranty lasts, so the above limitation

may not apply to you. The retailer shall not be liable for incidental, consequential, or

special damages arising out of or in connection with product use or performance except

as may otherwise be accorded by law. Some states do not allow theexclusion of incidental

or consequential damages, so the above exclusion or limitation may not apply to you. This

warranty gives specific legal rights, and you may also have other rights which vary from

state to state. This warranty supersedes all priorwarranties.

Lifetime Limited Warranty

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

Xxx-xxx

14826

792145xxxxxx

Safety Rules.....................................................................................................................................

Unpacking Your Fan ........................................................................................................................

Installing Your Fan ...........................................................................................................................

Installing the Light Kit....................................................................................................................

Your .............................................................................................................

Care of Your Fan ............................................................................................................................

Troubleshooting ............................................................................................................................

Specifications ...............................................................................................................................

Operating Transmitter

10.

11.

12.

13.

Table of Contents

1. Safety Rules

1. To reduce the risk of electric shock, insure electricity has been

turned off at the circuitbreaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical

Code and local electrical codes. Electrical installation should be

performed by aqualified licensed electrician.

3. WARNING: To reduce the risk of electrical shockand fire, donot

use this fanwith any solid-state fan speed control device.

4. Secure the mounting bracket directly to building structure joist

via the outlet box. The joist and its support must be able to

support the movingweight of the fan. (at least 50lbs.). Consult a

qualified electrician ifin doubt.

5. The fan must be mounted with a minimum of 7 feet clearance

from the trailingedge of theblades to the floor.

6. Do not operate the reverse switch while fan blades are in motion. Fan

must be turned off and blades stopped before reversing blade

direction.

7. Avoid placing objects in the pathof the blades.

8. To avoid personal injury or damage to the fan and other items, be

cautious when workingaround or cleaningthe fan.

9. Do not usewater or detergents when cleaningthe fan or fan blades.

A dry dust cloth or lightly dampened cloth will be suitable for

most cleaning.

10. After marking electrical connections, spliced conductors should

be turned upward and pushed carefully up into outlet box. The

wires should be spread apart with the grounded conductor and the

equipment-grounding conductor onone side ofthe outlet box.

11. Electrical diagrams are reference only. Light kit that are not

packed with the fan must be CUL Listed and marked suitable for

use with the model fan you are installing. Switches must be CUL

General Use Switches. Refer to the Instructions packaged with

the light kitsand switches forproper assembly.

WARNING: SUITABLE FOR USE WITH SOLID-STATE SPEED

CONTROLS.

WARNING

TO REDUCETHE RISK OFPERSONAL INJURY, DO NOTBEND THE

BLADE BRACKETS (ALSOREFERRED TOAS FLANGES)DURING

ASSEMBLYOR AFTERINSTALLATION. DO NOTINSERT OBJECTS IN

THE PATHOF THE BLADES.

NOTE

READ AND SAVE ALLINSTRUCTIONS!

Unpack your fanand check the contents. You should havethe following items;

1. Fan blades (5)

2. Canopy assembly

4. Coupling cover

5. Fan motor assembly

6. Blade arms(5)

7. Switch housing

Ball/downrod assembly

8. Switch housingcover

9. Light kit

10. Glass shades

11.

12.

14. Balancing kit

(4)

Receiver with 6wire nuts

Transmitter+holder+2 mounting screws

+ 2 plastic plugs

13. Extra plasticplug

Unpacking Your Fan 2.

WARNING

DO NOT INSTALL ORUSE FAN

IF ANYPARTIS DAMAGED OR MISSING.

CALL TOLLFREE 1-877-902-5588

15. Loose partsbag containing:

(2 #14 Wood screws, 2 lockwashers,

2 metal washers,2 star washers,3

plastic wire connectors)

b. Blade attachmenthardware

(16 screws, 16rubber washers )

Mounting hardware

3. Installing Your Fan

Tools Required

Phillips screwdriver, straight slot

screwdriver, adjustablewrench, step ladder,

and wire cutters.

Mounting Options

If there isn't an existing CUL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the

building structure. Use appropriate

fasteners and buildingmaterials. The outlet

box and its support must be able to fully

support the moving weight of the fan (at

least 50 lbs).Do not useplastic outlet boxes.

Figures 1,2 and 3 are examples of different

ways to mountthe outlet box.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar.(Fig.4) (available at

any Home Depotstore).

Outlet box

Provide strong

support

Recessed

outlet box

Mounting bracket

opening must be

toward the top

Figure 1 Figure 3

Figure 2

Angled ceiling

maximum

25 angle

Figure 4

Ceiling

hanger

bracket

Screws

Ceiling

canopy

Canopy

cover

Collar cover

Hitch pin

Figure 5

Downrod

Canopy

Canopy cover

Set screws

Lock pin

Hanger ball

Hanging the Fan

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly:

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counter clockwise. (Fig. 4)

Step 2. Remove the hanger bracket from the

canopy by loosening the two screws on the bottom

of the hanging bracket a half turn from the screw

head and turning the canopy counter clockwise.

(Fig. 4)

Step 3. Remove the hanger pin, lock pin and set

screws from the top of the motor assembly. (Fig.

Step 4. Route wires exiting from the top of the fan

motor through the collar cover, canopy cover,

canopy and then through the ball / downrod. (Fig.

Step 5. Align the holes at the bottom of the

downrod with the holes in the collar on top of the

motor housing (Fig.5). Carefully insert the hanger

pin through the holes in the collar and downrod.

Be careful not to jam the pin against the wiring

inside the downrod. Insert the locking pin through

the hole near the end of the hanger pin until it

snaps into its locked position, as noted in the

circle inset of Fig. 5.

Step 6. Tighten two set screws on top of the fan

motor firmly. (Fig. 5)

Place the downrod ball into the hanger

bracket socket. Rotate the downrod ball until

the groove of the downrod ball lines up with the

hook of the hanger bracket. (This will help

balance the fan.)

Step 7. Secure hanger bracket assembly

directly to a joist from the building structure

via the two knock out holes on the outlet box.

Use only the appropriate wood screws, star

washers, metal washers and lock washers

included with your fan. (Fig. 6)

Step 8.

(Fig. 7)

Step 9. Secure the safety cable to the building

structure. (Fig. 7)

Step 10. Connecting the wires (see making the

electrical connections)

WARNING

FAILURETO PROPERLY INSTALL LOCKING

PIN ASNOTED IN STEP5 COULD RESULT IN

FAN LOOSENINGAND POSSIBLY FALLING.

Figure 7

Hanger

bracket Safety cable

Ceiling

joist

Hanger

bracket

Hook

Lock

washers

Star

washers

Metal

washers

#14 Wood

screws

AC Wires

Outlet box

Figure 6

Make the Electrical Connections

WARNING: To avoid possible electrical shock,

be sure electricity is turned off at the main fuse

box before wiring.

NOTE: This remote control unit is equipped

with 16 code combinations to prevent possible

interference from or to other remote units. The

frequency switches on your receiver and

transmitter have been preset at the factory.

Please recheck to make sure theswitches on the

transmitter and the

receiver are set to the same

position, any combination of settings will

operate the fan as long as the transmitter and

receiver are setto the sameposition.(Fig. 8)

Step 1. (Figure 9) Insert the receiver into the

mounting bracket with the flat side of the

receiver facing theceiling.

Step 2. (Fig. 10) Motor to Receiver Electrical

Connections: Connect the black wire from

the fan to black wire marked "TO MOTOR L".

Connect the white wire from the fan to the

white wire marked "TO MOTOR N" from the

receiver. Connect the blue wire from the fanto

the blue wire marked "For Light" from the

receiver. Secure the wire connections with the

plastic wire nutsprovided.

Step 3. (Fig. 10) Receiver to House Supply

Wires Electrical Connections: Connect the

black (hot) wire from the ceiling to the black

wire marked "AC in L" from the receiver.

Connect the white(neutral) wire from the

ceiling to the white wire marked "AC in N"

from the Receiver. Secure the wire

connections with the plastic wire nuts

provided.

Step 4. (Fig. 10) If your outlet box has a

ground wire (green or bare copper) connect it

to the fanground wires; otherwiseconnect the

hanging bracket ground wire to the mounting

bracket. Secure the wire connection with a

plastic nut provided. After connecting the

wires spread them apart so that the green

and white wires are on one side of the outlet

box and blackand blue wires are on the other

side. Carefully tuck the wire connections up

into the outletbox.

Note: Fan must be installed at a maximum

distance of 20 feet from the transmitting unit

for proper signal transmission between the

transmitting unit andthe fan's receivingunit.

Figure 9

Receiver

Hanger

bracket

Figure 8

ONON

Code switch

Figure 10

White (neutral)

Green or bare

copper (ground)

White ("AC INN")

White ("to motor N")

Ground

(green)

(Connect to

ground wire on

hanger bracket

if no house

ground wire

exists.)

Outlet box

Black (hot)

Black ("AC INL")

Black ("to motor L")

Receiver

Blue ("for light")

Blue (light)

Black (motor)

Fan

Figure 11

Outlet box

Hanger

bracket

Canopy

cover

Screws

Finishing the Installation

Step 1. Slide the canopy up to ceiling and over

the 2 screws on the hanger bracket. Rotate

canopy clockwise. Next, while holding the

canopy with one hand, slide the canopy cover

over the screwsand rotate clockwise until tight.

Note: adjust the canopy screws as necessary

until the canopy and canopy cover are snug.

(Fig. 11)

WARNING

Make sure thenotch on thehanging bracket

properly sits inthe groove inthe hanger ball

before attaching thecanopy to thebracket by

turning the housinguntil it dropsinto place.

Rubber

washer

Blade

arm

Blade

Screws

Figure 13

Figure 14

Motor

Blade arm

Slot

Tab

Attaching the Fan Blades

Step 1 Attach blades to blade arms using three

screws and rubber washers. Start a screw

into the arm, do not tighten. Repeat for the

2 remaining screws and washers.

Step 2 Tighten each screw securely starting with

the center screw. Make sure the blade is straight.

(Fig. 13)

blade

Repeat steps for the remaining blades.

Step 3 Fasten the blade arms to the motor by

inserting the tab from the blade arms to the slot in

the bottom motor housing, then tighten the two

screws and washers already installed in the blade

arms. (Fig. 14)

WARNING

TO REDUCE THERISK OF PERSONALINJURY,

DO NOT BENDTHE BLADEARMS WHILE

INSTALLING, BALANCINGTHE BLADES, OR

CLEANING THE FAN. DO NO INSERT FOREIGN

OBJECTS BETWEEN ROTATING FAN BLADES.

CAUTION: Remove the screws from the

motor support plate, discard the motor

support plate and screws. (Fig. 12)

Motor support

plate

Screws

Figure 12

Tabla de contenidos

Otros manuales de Admirador de HAMPTON BAY

HAMPTON BAY

HAMPTON BAY AVERLY AK18B-BN Manual de usuario

HAMPTON BAY

HAMPTON BAY Radcliffe Manual de usuario

HAMPTON BAY

HAMPTON BAY 786-756 Manual de usuario

HAMPTON BAY

HAMPTON BAY WELLTON AM588-BN Manual de usuario

HAMPTON BAY

HAMPTON BAY Lonestar 52 Manual de usuario

HAMPTON BAY

HAMPTON BAY Vasner 529-751 Manual de usuario

HAMPTON BAY

HAMPTON BAY AC457-WB Manual de usuario

HAMPTON BAY

HAMPTON BAY HALPERT 52169 Manual de usuario

HAMPTON BAY

HAMPTON BAY FS40-21MA Manual de usuario

HAMPTON BAY

HAMPTON BAY 855975 Manual de usuario

HAMPTON BAY

HAMPTON BAY PALM BEACH Manual de usuario

HAMPTON BAY

HAMPTON BAY Altura Manual de usuario

HAMPTON BAY

HAMPTON BAY HAWKINS II Series Manual de usuario

HAMPTON BAY

HAMPTON BAY LUXENBERG EF200P-36 Manual de usuario

HAMPTON BAY

HAMPTON BAY 91171 Manual de usuario

HAMPTON BAY

HAMPTON BAY NORTH GROVE 52-HASLD Manual de usuario

HAMPTON BAY

HAMPTON BAY Colonial Bamboo Manual de usuario

HAMPTON BAY

HAMPTON BAY Devereaux II Manual de usuario

HAMPTON BAY

HAMPTON BAY 55370 Manual de usuario

HAMPTON BAY

HAMPTON BAY AC457-WH Manual de usuario

HAMPTON BAY

HAMPTON BAY AL958B-BN Manual de usuario

HAMPTON BAY

HAMPTON BAY ASHBURTON YG593-TB Manual de usuario

HAMPTON BAY

HAMPTON BAY 699 810 Manual de usuario

HAMPTON BAY

HAMPTON BAY Algiers 672 099 Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje