HAMPTON BAY Bentley II 328 478 Manual de usuario

328 478

Bentley II

13 in Ceiling Fan

Owner’s Manual

Bentley II

Ventilador de Techo de 33 cm

Manual del Propietario

Bentley II by Hampton Bay

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

Thank you for purchasing our ceiling fan. This product has been

manufactured with the highest standards of safety and quality.

Table of Contents

Safety Rules . . . . . . . . . . . . . . . . . . . . 1

Unpacking Your Fan . . . . . . . . . . . . . . 2

Installing Your Fan . . . . . . . . . . . . . . . 3

Operating Your Fan . . . . . . . . . 10

Care of Your Fan . . . . . . . . . . . . . . . . 11

Troubleshooting . . . . . . . . . . . . . . . . . 11

Specifications . . . . . . . . . . . . . . . . . . 12

Warranty Information . . . . . . . . . . . . 13

328-478

219032

792145356134

13” Bentley II

Ceiling Fan by Hampton Bay

Safety Rules - Read and Save These Instructions

To reduce the risk of electric shock, insure electricity has been turned off

at the circuit breaker or fuse box before beginning.

All wiring must be in accordance with the National Electrical Code

“ANSI/NFPA 70-1999” and local electrical codes. Electrical installation

should be performed by a qualified licensed electrician.

WARNING: To reduce the risk of electrical shock or fire, do not use this

fan with any solid-state fan speed control device. It will permanently

damage the electronic circuitry.

CAUTION: To reduce the risk of personal injury, use only the screws

provided with the outlet box.

The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 pounds. Use only ETL

Listed outlet boxes marked “FOR FAN SUPPORT”.

The fan must be mounted with a minimum of 10 feet clearance from the

trailing edge of the blades to the floor.

Avoid placing objects in path of the blades.

To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

Do not use water or detergents when cleaning the fan or fan blades. A dry

dust cloth or lightly dampened cloth will be suitable for most cleaning.

After making electrical connections, spliced conductors should be turned

upward and pushed carefully up into outlet box. The wires should be

spread apart with the grounded conductor and the equipment-grounding

conductor on one side of the outlet box and ungrounded conductor on the

other side of the outlet box.

All set screws must be checked and retightened where necessary before

installation.

10.

11.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY. DO NOT INSERT

FOREIGN OBJECTS IN – BETWEEN ROTATING FAN BLADES.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT WITH THE SCREWS PROVIDED WITH THE OUTLET BOX.

Unpacking Your Fan Unpack your fan and check the contents. You should have the following items:

Canopy assembly

Ball/downrod assembly

Coupling cover

Fan motor assembly

3-speed wall control with 2 mounting

screws and 4 wire nuts

Mounting plate with 2 mounting screws

5a.

5b.

WARNING

DO NOT INSTALL OR USE FAN IF ANY

PART IS DAMAGED OR MISSING.

CALL TOLL FREE 1-877-902-5588.

Electrical Hardware

(3 Plastic Wire Nuts)

Allen wrench

Installing Your Fan

Figures 1~2 are examples of different ways to

mount the outlet box.

If there isn't an existing ETL listed mounting box,

then read the following instructions. Disconnect

the power by removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the fan

(at least 35 lbs). Do not use plastic outlet boxes.

Tools Required

Mounting Options

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN

ONLY TO AN OULET BOX MARKED ACCEPT-

ABLE FOR FAN SUPPORT AND USE THE

MOUNTING SCREWS PROVIDED WITH THE

OULET BOX. OUTLET BOX COMMONLY USED

FOR THE SUPPORT OF LIGHTING FIXTURE

MAY NOT BE ACCEPTABLE FOR FAN SUPPORT

AND MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

Outlet Box

Figure 2

Figure 1

To hang your fan where there is an existing fixture

but no ceiling joist, you may need an installation

hanger bar as shown in Figure 4 (available at any

Home Depot store).

Figure 3

Phillips screwdriver, straight slot screwdriver, step

ladder and wire cutters.

Figure 5

Motor Wires

Ball/Downrod

Assembly

Ceiling Canopy

Canopy Bottom

Cover

Coupling Cover

Clevis Pin Cotter Pin

Set Screw

Allen wrench

Pin in Locked

Positioon

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly.

Hanging the Fan

Remove the decorative canopy bottom cover

from the canopy by turning the cover counter

clockwise. (Figure 4)

Remove the mounting bracket from the canopy

by removing the 1 of 2 screws from the bottom

of the mounting bracket and loosening the

other one a half turn from the screw head.

Next, turn the canopy counter clockwise to

removing the mounting bracket from the

canopy. (Figure 4)

Remove the clevis pin, cotter pin and set

screws from the top of the motor assembly, you

need to use the allen wrench to loosen your set

screws. (Figure 5)

NOTE: If a longer downrod is needed, take out

the screw located in the hanger ball, lower the

hanger ball and remove the pin, remove all 3

pieces from the downrod and assemble them

onto the new longer downrod before

proceeding step 4. (The longer downrod is

available at any Home Depot store)

Route wires exiting from the top of the fan

motor through the coupling cover, canopy

cover, canopy and then through the ball/

downrod. (Figure 5)

WARNING

FAILURE TO PROPERLY INSTALL COTTER PIN

AS NOTED IN STEP 5 COULD RESULT IN FAN

LOOSENING AND POSSIBLY FALLING.

Tighten two set screws at top of the fan motor

collar by allen wrench. (Fig. 5)

Align the holes at the bottom of the downrod

with the holes in the coupling on top of the

motor housing (Figure 5). Carefully insert the

clevis pin through the holes in the collar and

downrod. Be careful not to jam the clevis pin

against the wiring inside the downrod. Insert

the cotter pin through the hole near the end of

the clevis pin until it snaps into its locked

position, as noted in the circle inset of Fig. 5.

Figure 4

Ceiling

Mounting

Bracket

Ceiling Canopy

Canopy Bottom

Cover

Installing Fan to

the Electrical Box

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR OTHER PERSONAL INJURY.

MOUNT FAN ONLY TO AN OUTLET BOX OR

SUPPORTING SYSTEM MARKED ACCEPTABLE

FOR FAN SUPPORT AND USE THE MOUNTING

SCREWS PROVIDED WITH THE OUTLET BOX.

Figure 6

ETL Listed Outlet Box

Ceiling Mounting

Bracket

120V

Wires

Mounting

Screws (Supplied

with Electrical Box)

Figure 7A

Safety Cable

Ceiling

Mounting

Bracket

Pass the 120-volt supply wires through the

center hole in the ceiling mounting bracket as

shown in Figure 6.

Install the ceiling mounting bracket on the

outlet box with the screws and washers

provided with your outlet box. (Figure 6)

Security tighten the two mounting screws.

Hanging the assembled fan onto the mounting

bracket, place the downrod ball into the

mounting bracket. (Figure 7)

Secure the safety cable to the building structure

as shown in Figure 7A.

WARNING

THE TAB IN THE RING MUST REST IN THE

GROOVE OF THE HANGER BALL AS FIGURE 7.

FAILURE TO PROPERLY SEAT THE TAB IN THE

GROOVE COULD CAUSE DAMAGE TO WIRING.

Figure 7

Making the Electrical Connections

WARNING

TO AVOID POSSIBLE ELECTRICAL SHOCK, BE SURE ELECTRICITY IS TURNED OFF AT THE

MAIN FUSE BOX BEFORE WIRING.

NOTE

INSTALLATION OF THIS FAN REQUIRES THAT A THREE-CONDUCTOR CABLE WITH

GROUND WIRE BE RUN BETWEEN CEILING AND WALL OUTLET BOX, OR THE OSCILLAT-

ING FEATURE WILL NOT WORK.

Disconnect the power and remove the existing wall plate and switch from the wall outlet box (Figure 8).

Set knob on the wall control in 0 position.

Make wire connections as follows, using the wire nuts supplied:

a. Speed/oscillation control wire connection (see figure 9)

CONNECT

(From speed/oscillation switch)

Blue wire (FOR OSCILLATION)….........…………

Black wire (TO MOTOR L)………………………..

Black/white wire (AC IN L)………………………..

Yellow/green ground wire……........……………….

• If your wall outlet box has a ground wire (green or bare copper), connect the Speed/oscillation control's yellow/green ground wire to it; otherwise

connect the Speed/oscillation control's yellow/green ground wire directly to one of the screws from the wall outlet box.

b. Fan wire connection (see figure 10)

CONNECT

(From fan)

Blue fan wire …………….............

Black fan wire …………….............

White wire……………....…............

Green wire………………................

If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed

by a licensed electrician.

Figure 8

Switch

Wall Outlet Box Wall Plate

Screws

Figure 9

BLUE

BLACK

WHITE

BLACKW/

WHITE

BLUE (or RED)

(From wall outlet box)

Blue or red wire

White wire

Black wire from A/C supply source

Outlet box green wire

(Conductor cable between ceiling and wall outlet box)

Blue or red wire

White wire

White wire from A/C supply source

Ground conductor of 120V supply, it may be a bare wire or a wire with green colored insulation.

YELLOW/GREEN

GROUND

Figure 10

SUPPLY CIRCUIT

BLUE (or RED)

BLUE

BLACK

BLUE

BLACK

Ground

Conductor

Ceiling Outlet Box

Green Ground

Lead

YELLOW/GREEN

GROUND

Ground to

Downrod

GREEN

WHITE WHITE

Wall Outlet Box

BLACK

BLACKW/WHITE

BLACK

WHITE

Speed/oscillation Switch

BLUE(or RED)

• Dash lines are 3-conductor cable between ceiling and wall outlet box.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Admirador de HAMPTON BAY

HAMPTON BAY

HAMPTON BAY 52" Huntington III Manual de usuario

HAMPTON BAY

HAMPTON BAY Torrington Manual de usuario

HAMPTON BAY

HAMPTON BAY CHASTAIN II Manual de usuario

HAMPTON BAY

HAMPTON BAY 7114-01 Manual de usuario

HAMPTON BAY

HAMPTON BAY 120-231 Manual de usuario

HAMPTON BAY

HAMPTON BAY Pendleton 91252 Manual de usuario

HAMPTON BAY

HAMPTON BAY Redington 740-125 Manual de usuario

HAMPTON BAY

HAMPTON BAY Gazebo II YG187-WH Manual de usuario

HAMPTON BAY

HAMPTON BAY Fulton 140201 Manual de usuario

HAMPTON BAY

HAMPTON BAY AVERLY AK18B-BN Manual de usuario

HAMPTON BAY

HAMPTON BAY 597-730 Manual de usuario

HAMPTON BAY

HAMPTON BAY METARIE II 24 Manual de usuario

HAMPTON BAY

HAMPTON BAY HARPER AM214-WH Manual de usuario

HAMPTON BAY

HAMPTON BAY ASBURY Manual de usuario

HAMPTON BAY

HAMPTON BAY 52-RMG Manual de usuario

HAMPTON BAY

HAMPTON BAY 80213 Manual de usuario

HAMPTON BAY

HAMPTON BAY AG524I-ORB Manual de usuario

HAMPTON BAY

HAMPTON BAY 91371 Manual de usuario

HAMPTON BAY

HAMPTON BAY Parker Ridge Manual de usuario

HAMPTON BAY

HAMPTON BAY Largo Manual de usuario

HAMPTON BAY

HAMPTON BAY AL975-BN 593-552 Manual de usuario

HAMPTON BAY

HAMPTON BAY HAWKINS II Series Manual de usuario

HAMPTON BAY

HAMPTON BAY Gazebo II Plus Manual de usuario

HAMPTON BAY

HAMPTON BAY BENNINGTON 52389 Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje