Hama 176932 Manual de usuario

RUS

Operating Instructions

Bedienungsanleitung

Mode d‘emploi

Instrucciones de uso

Руководство по эксплуатации

Istruzioni per l‘uso

Instrukcja obsługi

Návod k použití

Návod na použitie

Manual de utilizare

176932

TS35C

Outdoor Sensor

Außensensor

433MHz

HYGRO-THERMO

22.7C

GOperating instruction

Controls and Displays

A Measuring station

1. LED indicator

2. Battery compartment

3. RESET button = restores factory settings

4. CHANNEL slide switch = selects channel

5. Recess for wall mounting

6. LCD display

Thank you for choosing a Hama product.

Take your time and read the following instructions and information

completely. Please keep these instructions in a safe place for future

reference. If you sell the device, please pass these operating instructions

on to the new owner.

1. Explanation of Warning Symbols and Notes

Warning

This symbol is used to indicate safety instructions or to draw your

attention to specic hazards and risks.

Note

This symbol is used to indicate additional information or important

notes.

2. Package Contents

•TS35C Outdoor Sensor

•These operating instructions

3. Safety Notes

•The product is intended for private, non-commercial use only.

•Do not operate the product outside the power limits given in the

specications.

•Do not use the product in moist environments and avoid splashes.

•Do not use the product in the immediate vicinity of heaters or other

heat sources or in direct sunlight.

•Do not use the product in areas where the use of electronic devices

is not permitted.

•Do not put the product near interference elds, metal frames,

computers, TVs, etc. Electronic devices and window frames can

negatively affect the product’s functionality.

•Do not drop the product and do not expose it to any major shocks.

•Do not open the device or continue to operate it if it becomes

damaged.

•Do not attempt to service or repair the product yourself. Leave any and

all service work to qualied experts.

•Keep the packaging material out of the reach of children due to the

risk of suffocation.

•Dispose of packaging material immediately according to locally

applicable regulations.

•Do not modify the product in any way. Doing so voids the warranty.

Warning – Batteries

•Immediately remove and dispose of dead batteries from the

product.

•Only use batteries (or rechargeable batteries) that match the

specied type.

•Do not mix old and new batteries or batteries of a different type

or make.

•When inserting batteries, note the correct polarity (+ and -

markings) and insert the batteries accordingly. Failure to do so

could result in the batteries leaking or exploding.

•Do not overcharge batteries.

•Keep batteries out of the reach of children.

•Do not short circuit the batteries/rechargeable batteries and keep

them away from uncoated metal objects.

4. Getting started

•Open the battery compartment (2).

•Move the CH slide switch (4) to the left or right to select the channel

on which the measuring station transmits.

•Insert two AA batteries with the correct polarity.

•Once the channel has been assigned to a transmitter, it can only be

changed by removing the batteries or by resetting the measuring

station (see section 6.5 Reset).

•Then close the battery compartment cover.

Replacing the batteries

•Open the battery compartment (2), remove and properly dispose of

the dead batteries and insert two new AAA batteries with the correct

polarity. Then close the battery compartment cover.

Note

Before use, make sure that you insert the batteries in the measuring

station rst and then in the base station.

5. Installation

Note – Installation

•We recommend initially placing the base and measuring stations

in the intended locations without installing them and making all

the settings described in 6. Operation.

•Only install the stations once the appropriate settings have been

made and a stable wireless connection is established.

Note

•The wireless transmission range between the measuring and base

stations is up to 30 metres in open spaces.

Before installation, ensure that wireless transmission will not

be disrupted by interference or obstacles like buildings, trees,

vehicles, high-voltage lines, etc.

•Before the nal installation, ensure that there is sucient

reception between the intended installation locations.

•When installing the measuring station, ensure that it is protected

from direct sunlight and rain.

•The international standard height for measuring air temperature is

1.25 m (4 ft) above ground.

Warning

•Buy special or suitable installation material from a specialised

dealer for wall-mounting.

•Ensure that no faulty or damaged parts are installed.

•Never apply force during installation. This could damage the

product.

•Before installation, ensure that the chosen wall is suitable for

the weight to be installation, and make sure that there are

no electrical wires, water, gas or other lines in the wall at the

installation site.

•You can position the measuring station on a level outdoor surface

using the base.

•We recommend installing the measuring station securely on an

outdoor wall.

•Install an anchor, screw, nail, etc. in the wall of your choice.

•Hang the measuring station using the opening intended for this

purpose (4).

6. Operation

6.1. Connection to the measuring station

•To connect the base station and the measuring station, place the two

devices as close together as possible.

•After you insert the batteries, the base station automatically searches

for a connection to the measuring station and performs initial setup.

•If the device does not connect automatically, the manual search

program on the base station must be started.

Note

•Initial setup takes approximately 5 minutes.

•During the connection attempt, the radio symbol and the LED

indicator (1) on the measuring station will ash.

•Do not press any buttons during setup. Otherwise, values may

not be transmitted correctly and there is a risk of value errors and

inaccuracies.

•The setup process is completed when the indoor and outdoor

measurement data is displayed on the base station.

•The measured value is automatically updated by the base device

about every 60–64 seconds.

6.2. Selecting the channel/Other measuring stations

Note

•You can connect up to three different base stations to the

measuring station. Ensure that the base station and measuring

station are set to the same channel. Suitable base stations can be

found at www.hama.com

•The transmission channel on the supplied measuring station can

be changed/set (CH1, CH2, CH3).

•The measuring station is suitable for the following base stations:

113984, 113985, 113986

6.3. Low battery charge

Once the battery symbol appears on the display of the base station,

the capacity of the batteries in the measuring station is very low. Replace

the batteries immediately.

Note – Replacing the batteries

•Note that the stations have to be resynchronised each time after

you change the batteries in the measuring or base station.

•To do this, remove the batteries from the other station and then

reinsert them, or change them as required.

6.4 Reset

Press the RESET button (3) to restart the station. The measuring station

returns to the factory settings.

7. Care and Maintenance

•Only clean this product with a slightly damp, lint-free cloth and do not

use aggressive cleaning agents.

•Make sure that water does not get into the product.

8. Warranty Disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for

damage resulting from improper installation/mounting, improper use of

the product or from failure to observe the operating instructions and/

or safety notes.

9. Service and Support

Please contact Hama Product Consulting if you have any questions about

this product.

Hotline: +49 9091 502-115 (German/English)

Further support information can be found here:

www.hama.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Accesorios de Hama

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario