Hall Research Technologies UHBX-3S Manual de usuario

Software GUI

User’s Manual

CUSTOMER

SUPPORT

INFORMATION

FREE support, Call 714-641-6607 or email [email protected]

Hall Research, 1163 Warner Ave., Tustin, CA 92780

Web site: www.hallresearch.com UMA1220 GUI Supplement

Rev A

EDID & Configuration

Manager Software

UHBX-3S/6S and UHBX-6S

Table of Contents

1. WINDOWS™ SOFTWARE INSTALLATION 1

1.1. General 1

1.2. Installation Prerequisites 1

1.3. Software Installation 1

2. USING THE SOFTWARE 2

2.1. General 2

2.2. USB Device Detection 2

2.3. Controls 3

2.4. Status 5

2.5. Device Name 7

2.6. Status Bar 7

2.7. Tool Bar Menu 7

2.8. Firmware Update 8

Trademarks

Hall Research and its logo are trademarks of Hall Research Technologies, Inc. All other

trademarks mentioned in this manual are acknowledged as the property of the trademark

owners.

UHBX-3S and UHBX-6S

1. Windows™ Software Installation

1.1. General

The UHBX-3S/6S graphical user interface (GUI) is Windows™ software used to

configure advanced settings of the UHBX-3S/6S. The software requires a USB

connection from the PC to the device. A USB cable is provided with each device.

The GUI can monitor and configure several devices simultaneously. PCs that have

multiple USB ports or use external USB hubs can use the same GUI and address each

device individually.

This manual is applicable to both the UHBX-3S and UHBX-6S models. The illustrations

figures herein are representative for both models and there might be slight changes

between the actual GUI software.

1.2. Installation Prerequisites

•A PC with Windows XP™ OS or later

•USB port

•Microsoft™ .NET Framework 2.0 or later (most recent OS including Windows 7 and

10 typically include this and no action is required). If .NET Framework 2.0 or later is

not installed on your PC, the Microsoft™ website has free downloads available.

1.3. Software Installation

•If any version of this software was previously installed, UNINSTALL the program

first from either the Add/Remove Programs section of the control panel or by

running the previous installation SETUP.EXE and selecting “remove application”.

•Install the software by executing the SETUP.EXE program from the installation

source directory

•Most users can accept the default settings, but if you want to specify a particular

installation directory other than the default, you may do so.

•Once the UHBX-3S/6S software installation has completed,

either click the desktop icon or navigate the Start Menu to

Start  Programs  Hall Research  UHBX-3S/6S Manager

UHBX-3S and UHBX-6S

2. Using the Software

2.1. General

The UHBX-3S/6S Manager is a Windows GUI that to remotely control and monitor the

UHBX-3S/6S device via a USB connection. It also provides you an ability to manage the

EDID by learning it from a desired LCD monitor connected to any output, importing any

custom EDID into the device, exporting the device’s EDID to a file, updating any future

firmware into the device, and many more.

2.2. USB Device Detection

The UHBX-3S/6S Manager automatically configures the USB port after connection to the

device (using standard Windows™ USB drivers) and does not require any special USB

drivers to be installed.

Once connected to a USB port, the Windows™ system will detect and use the

appropriate USB driver. The first time you connect the device to the PC, you may

experience a short delay and a windows notification pop-up message may appear.

If no UHBX-3S/6S device is attached to the PC, the on-screen fields will be disabled

(grayed out).

This detection and driver installation occurs only when the UHBX-3S/6S

is connected to the PC for the first time. Afterwards, reconnected devices

automatically configure themselves with no delay or message.

UHBX-3S and UHBX-6S

Once the UHBX-3S/6S Manager has detected a valid connection UHBX-3S/6S

device, the control and status menus will enable as shown below.

2.3. Controls

The UHBX-3S/6S Manager provides you more control and flexibility of the device than

the front panel of the unit alone.

Video EDID

The UHBX-3S/6S builds an EDID table that the source connected to the input can read.

The EDID mode can be set to either emulate or pass-thru.

Emulate - The internally stored EDID

passes to the source. This EDID can be a

factory default or a learned EDID from one

of the sink LCD monitors or other device

connected to the local output.

Pass-thru - The EDID passed to the source

comes directly from a sink LCD monitor connected to the output.

EDID Routing Modes

UHBX-3S and UHBX-6S

Learn EDID

An EDID can be learned from a sink LCD monitor

connected to any outputs. First select an output,

just click the Learn button to learn the EDID from

the connected monitor or device.

Set RS232 Start Channel

The UHBX-3S/6S’s output can be

referenced by a number from 1 to 99,

which makes communicating to a desired

remote serial receiver easier when there

are more than one UHBX-3S/6S devices

connected in daisy chain.

By default, Output 1 of each device starts with number 1, and this number will be

incremented by one for the next output. If Output 1 is changed to 12, the Output 2 and

Output 3 will be 13 and 14 respectively.

This output channel numbering is used to transmit/receive data to or from the specified

serial receiver.

Current Connection – Allow you to view

you to view the current output connection

that the controller is connected to in

addition to the baud rate, and the parity

that the controller is communicating at with

the remote serial receiver.

UHBX-3S and UHBX-6S

Miscellaneous

Cycle HPD – Use this button to send a

500ms Hot Plug Detect pulse signal to the

video source. It has the same effect of

unplugging the HDMI input cable and

plugging it back in. This forces the source

to re-initialize its HDMI video output connection (read EDID, and implement HDCP if

required).

Power Management – When selected, the UHBX-3S/6S device will check for the

presence of source +5V and sink HPD. If neither +5V nor HPD is detected, the

HDBaseT extender module at the output will be in low power mode. When not

selected, the HDBaseT extender module at the output will always be either in Auto

or Long Reach mode.

Set HDBaseT Mode

The HDBaseT output can be individually set to

either Auto or Long Reach mode.

Auto - When set to Auto, the HDBaseT

output will follow the current mode on the

receiver. By default, it is the HDBaseT

mode.

Long Reach - When set to Long Reach, the HDBaseT output will have the

strongest signal from the sender to the receiver. However, this mode does not

support deep color or 4K video.

2.4. Status

The UHBX-3S/6S Manager provides you an instant status update on input video, the

HDBaseT connection, and the current EDID passed to the video source.

Input Video

LED indicators display the input video status.

When on, the video type indicated has been detected.

When off, no video input is being received.

The HDCP LED whether the input video has HDCP Encryption

enabled or disabled.

UHBX-3S and UHBX-6S

HDBaseT

LED indicators display the HDBaseT status.

On indicates the HDBaseT connection has

been detected; otherwise, its LED is off.

The cable length is in meters, and does not

apply when in Long Reach mode.The

calculation varies according to cable

quality.

EDID Table

The data shown in the EDID table shows the current EDID given to the source.

When the Link LED is flashing, it is indicating the HDBaseT extender

module at the specified output is in Low Power mode due to either +5V

video source or the HPD from the sink is not detected.

UHBX-3S and UHBX-6S

2.5. Device Name

Assigns a descriptive name to the UHBX-3S/6S device that is a maximum 8 characters

long. This information is stored in the device. Assigning unique device names to each

device is useful to identify each device. This is handy if you are going to upload different

configurations for each device, or if you intend to connect

multiple devices simultaneously to a PC and use the

software to control several at once.

The FACTORY DEFAULT name is USBDEVHR.

2.6. Status Bar

The bottom bar of the screen shows the USB connection status as follows:

This indicates the software has not detected any

UHBX-3S/6S devices and is searching the USB

ports for devices.

The controls and status indicators are disabled until a valid UHBX-3S/6S device is

attached and properly identified by the software.

The number of UHBX-3S/6S detected by the software is

shown.

2.7. Tool Bar Menu

The UHBX-3S/6S Manager consists of three main menus.

File

The File menu consists of the Exit selection as

shown.

Exit – Exit the UHBX-3S/6S Manager

software.

Tools

The Tools menu consists of the following menu items as shown.

Factory Defaults – Restore the device to

factory default settings.

Import EDID – Import an EDID (256-byte

binary into the unit).

UHBX-3S and UHBX-6S

Export EDID – Save the current EDID as a 256-byte binary file. This file can be

edited as reloaded using Import EDID tool selection.

HDBaseT Programmer – Can be used to update any HDBaseT extender module.

Firmware Update – Allow you to update any future device firmware.

Help

About… - Displays the current version of UHBX-

3S/6S Manager, device firmware, and USB serial

number.

2.8. Firmware Update

After the Firmware Update from the tools menu is selected, the UHBX-3S/6S Manager

will open a Firmware Update window as shown. Browse to the firmware update file and

click the “Upload” button.

Otros manuales para UHBX-3S

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cables y conectores de Hall Research Technologies

Hall Research Technologies

Hall Research Technologies Mini-Cat UV4-S Manual de usuario

Hall Research Technologies

Hall Research Technologies 200A Manual de usuario

Hall Research Technologies

Hall Research Technologies SP-HD-2B Manual de usuario

Hall Research Technologies

Hall Research Technologies SP-HD-4B Manual de usuario

Hall Research Technologies

Hall Research Technologies ULTRA-V Series Manual de usuario

Hall Research Technologies

Hall Research Technologies UHBX-3S Manual de usuario

Hall Research Technologies

Hall Research Technologies UVA-4 Manual de usuario

Hall Research Technologies

Hall Research Technologies UHBX-3S Manual de usuario

Manuales populares de Cables y conectores de otras marcas

Philips

Philips SWA6310 Manual de usuario

StarTech.com

StarTech.com CRJ4550PK Manual de usuario

Nohau

Nohau EMUL-IP2K-PC Manual de usuario

Foxun

Foxun SX-SP144E-HD4K2K Manual de usuario

Philips

Philips SWA3305W Manual de usuario

opticis

opticis Stretch DVIM1-1P0x Manual de usuario

Volkswagen

Volkswagen VAS 6558A Manual de usuario

NEXIBO

NEXIBO N-13 Manual de usuario

CYP

CYP PU-1H3HBTL Manual de usuario

Allen-Bradley

Allen-Bradley 1784-u2dhp Manual de usuario

Global Caché

Global Caché Flex Link Blaster Manual de usuario

Hauppauge

Hauppauge USB-Live2 Manual de usuario

Fenix

Fenix MPSV 15 Manual de usuario

BEGA

BEGA 71 085 Manual de usuario

Tesla

Tesla HPWC Manual de usuario

GAMERON

GAMERON LUXURY TV CABLE Manual de usuario

molex

molex Milli-Grid Dual row 87568 Series Manual de usuario

Burndy

Burndy Continental Industries thermOweld CRE-7 Manual de usuario