Hakko Electronics 373 Manual de usuario

Thank you for purchasing the HAKKO 373 Self Feeder.

Please read this manual carefully before operating the

HAKKO 373. Store the manual in a safe, easily accessible

place for future reference.

CAUTION: You must install the Solder Dia. Adjustment Ring before use.

SELF FEEDER

TABLE OF CONTENTS

Precautions ................................................................. 1

Specifications .............................................................. 1

Names of Parts ........................................................... 2

Setting Up the HAKKO 373 ......................................... 3

Operation .................................................................... 6

Replacement of Parts .................................................. 8

Options & Replacement Parts ..................................... 9

Parts List ................................................................... 11

Troubleshooting Guide .............................................. 13

Precautions

CAUTION

Setting up should be done while the soldering iron is cool, or you may get burnt.

Do not force the guide pipe bend or turn as this may result in damage.

Do not operate with tube bending or holding in sharp angle. It may cause to clogging.

Input of switching is no-voltage input. Do not apply voltage to the jack for switch.

Periodically, remove the guide pipe and clean out clogged flux.

Do not force the adjustment screw to adjust the amount of solder return. It may cause to damage.

If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualified person in order to avoid personal injury or damage to the unit.

Specifications

Usable Solder

Usable solders are as follows. Some of the parts should be changed according to the diameter of

solder desired to use.

(mm)

(inch)

0.6, 0.65, 0.8, 1.0, 1.2, 1.6

0.024, 0.025, 0.031, 0.039, 0.047, 0.063

Maximum quantity of usable solder is 1 kg (2.2 pounds).

Dia. of

solder

Usable Soldering Iron

Soldering Iron

HAKKO 900M (For HAKKO 926, 927, 928)

HAKKO 900L (For HAKKO 926, 927, 928)

HAKKO 902 (For HAKKO 931)

HAKKO 903 (For HAKKO 939)

HAKKO 904 (For HAKKO 929)

HAKKO DASH

HAKKO MACH-I

HAKKO 907 (For HAKKO 936, 937)

HAKKO 908 (For HAKKO 936, 937)

Remarks

Operationable only with Foot Switch

Specifications

Power Consumption

Motor Rate

6 W

DC 24 V 3.2W

0~7 sec.

4.5~26 mm (0.14~1 in.)/sec.

0~182 mm (0~7.2 in.)

0~5 mm (0~0.2 in.) (Fixed Speed)

107(W) x 110(H) x 215(D)

Approx.1.5 kg/3.3 pounds

Solder Feed Time

Solder Feed Speed

Solder Feed Quantity

Solder Return Quantity

Outer Dimensions

Weight

Names of Parts

Jack for Switch

Feed Speed Control Knob

Feed Time Control Knob

Mode Switch

Power Switch

Release Lever

Securing Screw

Tension Adjustment Knob

Tension Gear Guide Shaft

Adjustment for the amount of solder return

Feed Gear

Supply Nozzle

Solder Bobbin Shaft

Solder Dia. Adjustment Ring

Tension Gear

Setting Up the HAKKO 373

1. Install the Solder Dia.

Adjustment Ring

1. Remove the tension gear guide shaft.

2. Attach the solder dia. adjustment ring according to the

diameter of your desired solder and attach the tension

gear guide shaft.

Solder Dia.

Adjustment Ring

Tension Gear Guide Shaft

Tension Gear

2. Setting the Guide Pipe

Asse’y

Set the guide pipe asse’y between the nipple (or nut) and

handle, and secure it. Washer may need depend on the type

of iron. Please refer to the following figure.

Setting up should be done while the soldering iron is cool, or you may get burnt.

Do not force the guide pipe bend or turn as this may result in damage.

Do not operate with tube bending or holding in sharp angle. It may cause to clogging.

Guide Pipe Asse’y

Handle

Nut

HAKKO 900, HAKKO DASH SERIES & 907, 908

Handle

Guide Pipe Asse’y

Nipple Wave Washer (No. B2684)

HAKKO 902, 903, 904

Handle

Guide Pipe Asse’y

Nut Ring Washer

HAKKO MACH-I SERIES

(for 918 – No. B2685)

(for 920, 921, 922 – No. B2686)

3. Setting the Tube Unit

The tube is double structure. Insert the inside tube into the

hole of the connection, and the outside black tube should

fully cover the screw part of the connection. Be sure that not

to bend the tube.

(a) Attach the Tube to Guide Pipe

Asse’y.

(b) Set the Attachment on the

Handle of Soldering Iron.

NOTE

The Attachment is not necessary if you use HAKKO

MACH-.

i. Position the attachment on the handle of iron. Decide which

outlet of attachment should use for the tube as the tube

can be pulled out from either way of the attachment. Find

the best position where can connect the tube straight to

the pipe. Be careful not to damage the inner wiring if

replace the tube inside of the attachment.

ii. Secure the attachment. Set the attachment on the handle

securely with clips and adhesive tape on backside of the

attachment. Refer to the following figure on the setting

position of the attachment and the guide pipe. Pay attention

on the setting angle of the guide pipe and the attachment.

4. Connect the Feeding

Nozzle

Insert the feeding nozzle into the feeding unit on the top of

the station, and secure it with screw.

NOTE

Securing the screw excessively may break the feeding

nozzle.

5. Connect the Mini-plug Insert the mini-plug branching from the tube unit into the

jack of the station.

NOTE

Connect the mini-plug of foot switch to the station if you

use HAKKO MACH-.

Nozzle

Guide Pipe

Securing Nut for Guide Pipe Connection

Tube Attachment

ClipsGuide Pipe Holder

Setting Up the HAKKO 373

6. Setting the Solder Set a new solder after pull the old solder out when the old

one left in tube.

(a) Remove the tension gear guide shaft. And attach the

solder dia. adjustment ring according to the diameter of

your desired solder.

(b) Insert the solder bobbin shaft in the solder bobbin and

mount it on rear of the station. Solder should be fed over

the bobbin as the following figure.

(d) With pressing release lever, put the inserted solder of

approx. 10 mm/0.4 in. into the feeding nozzle through

between tension gears.

(e) Power switch on, and set MODE to MANUAL .

(f) Press the trigger switch, and feed the solder.

7. Changing the Solder

Diameter

Replace the solder dia. adjustment ring, when using the

soldering iron continuously but desire to change the

diameter of solder. The guide pipe asse’y should change

according to the diameter of solder. Refer to the section

“Replacement of Parts”.

(a) Power switch off. Open the release lever and roll back the

left solder to the bobbin.

(b) Remove the tension gear guide shaft, and replace the

solder dia. adjustment ring according to desired solder

dia. Remove the tension gear guide shaft turning with a

spanner or pliers.

8. Use in Vertical Vertical use is available. Fixing in vertical is as following figure.

46mm 2- 4.2

Operation

Solder will be fed by pressing the feed switch (or foot switch).

MODE AUTO MODE

If you press the feed switch, solder will be fed with set time

and speed independently of length of pressing time.

MANUAL MODE

Solder will be fed with set speed during pressing the feed

switch.

Setting for Feeding Time

and Speed

Set the speed before the time. For the setting speed, both

AUTO

& MANUAL are effective, but only

AUTO

is effective

for setting time.

Adjustment for the

Amount of Solder

Return

After feed solder, specific length of solder can be returned.

This solder return function permits use for simple robots.

Amount of solder return is adjustable within 0~13 mm

(0~0.51 in.). Solder should be rolled back if the amount of

solder return is bigger than the amount of solder feed. Please

set the amount of solder return as small as possible. If the

tip of the returning solder reaches to the guide pipe, flux will

easily accumulate at this point. Be sure that it will not happen.

Insert a driver into a adjustment hall on the side of the station.

Turn left for smaller and turn right for bigger amount.

Adjustment of Tension When adjust the tension, be sure that not the gear to be

slipped during feed solder, or do not force to feed solder

slipping gear when solder clog.

Set the tension gear loosely for fine solder ( 0.6mm, 0.8mm/

0.024 in., 0.031 in.). Refer to the following chart.

Solder Dia. 0.6mm

maximum

1.0mm

14mm

1.6mm

10mm

Operation

Usage of Iron Holder

If you use HAKKO 926, refer to the following figure to set the

iron holder. (As for the HAKKO 926, the setting is available

only on it’s left.)

• HAKKO 926

• HAKKO 631 Simply replace the iron holder if you use with iron holder

HAKKO 631 for except HAKKO 926.

• HAKKO 907, 908 Place the soldering iron in the iron holder so that the right

side of the guide pipe holder fits to the right side of the iron

receptacle.

When you want to fit it to the left side of the iron receptacle,

remove the securing nut for the guide pipe and the

connection; then reattach them in the opposite side.

Iron Receptacle

Spring Iron Holder

Holder Mounting Base

Thumb screw

Set the iron receptacle in the spring iron holder keeping the

iron tip and the guide pipe horizontally.

Replacement of Parts

1. When you change the

Solder Diameter

Please replace the parts indicated on the following chart when

you change solder diameter.

Solder Dia.

Adjustment Ring

replace

Changing matter

From the range of 0.6~1.0mm to the range of 0.6~1.0mm

From the range of 1.2~1.6mm to the range of 1.2~1.6mm

From the range of 0.6~1.0mm to the range of 1.2~1.6mm

From the range of 1.2~1.6mm to the range of 0.6~1.0mm

Nozzle

replace

Guide

Pipe

same

replace

Tube

Unit

same

replace

2. When you change the

Soldering Iron

Please replace the tube unit and guide pipe asse’y, when

you change the soldering iron. It is not necessary to replace

the parts if the items are in the same frame in the following

chart. Foot switch is necessary if you use the HAKKO

MACH-I.

Tube Unit

Guide Pipe Asse’y

900M, 900L, N452, N453, N454 902, 903, 904

N452, N453, 900M N454, 900L 920, 921, 922 918

918, 920, 921, 922 907, 908

902, 903, 904 907 908

Options & Replacement Parts

Part No.

B1626

B1627

B1628

B1629

B1630

B1631

B1672

B1632

B1673

B1957

B1958

B2143

B2144

B1674

B1675

B1676

B1677

B1678

B1679

B1680

B1681

B1682

B1683

B1684

B1685

B1686

B1687

B1688

B1689

B1690

B1691

B1692

B1693

Part Name

Solder Dia. Adjustment Ring

Tube Unit A/with Switch

Tube Unit B/with Switch

Tube Unit C

Tube Unit D

Tube Unit E/with Switch

Tube Unit F/with Switch

Tube Unit J/with Switch

Tube Unit K/with Switch

Guide Pipe Asse’y

Dia. of Solder

0.6, 0.65mm

0.8mm

1.0mm

1.2mm

1.6mm

0.6~1.0mm

1.2~1.6mm

0.6~1.0mm

1.2~1.6mm

0.6~1.0mm

1.2~1.6mm

0.6~1.0mm

1.2~1.6mm

0.6, 0.65mm

0.8mm

1.0mm

1.2mm

1.6mm

0.6, 0.65mm

0.8mm

1.0mm

1.2mm

1.6mm

0.6, 0.65mm

0.8mm

1.0mm

1.2mm

1.6mm

0.6, 0.65mm

0.8mm

1.0mm

1.2mm

1.6mm

Soldering Iron

900M, 900L, DASH

MACH-I

902, 903, 904

907, 908

900M, N452, N453

900L, N454

920, 921, 922

918

Otros manuales para 373

Tabla de contenidos

Otros manuales de Pistola de soldar de Hakko Electronics

Hakko Electronics

Hakko Electronics FX-951 Manual de usuario

Hakko Electronics

Hakko Electronics FX-952 Manual de usuario

Hakko Electronics

Hakko Electronics 474 Manual de usuario

Hakko Electronics

Hakko Electronics FR-810B Manual de usuario

Hakko Electronics

Hakko Electronics A1560 Manual de usuario

Hakko Electronics

Hakko Electronics FX-301 Manual de usuario

Hakko Electronics

Hakko Electronics 485 Manual de usuario

Hakko Electronics

Hakko Electronics 937 Manual de usuario

Hakko Electronics

Hakko Electronics 485 Manual de usuario

Hakko Electronics

Hakko Electronics 853 Manual de usuario

Hakko Electronics

Hakko Electronics FX?801 Manual de usuario

Hakko Electronics

Hakko Electronics FR8601-01 Manual de usuario

Hakko Electronics

Hakko Electronics FP-101 Manual de usuario

Hakko Electronics

Hakko Electronics FP-102 Manual de usuario

Hakko Electronics

Hakko Electronics FX-100 Manual de usuario

Hakko Electronics

Hakko Electronics FX-950 Manual de usuario

Hakko Electronics

Hakko Electronics 942 Manual de usuario

Hakko Electronics

Hakko Electronics 816 Manual de usuario

Hakko Electronics

Hakko Electronics FX-971 Manual de usuario

Hakko Electronics

Hakko Electronics FX-301B Manual de usuario

Hakko Electronics

Hakko Electronics FX?801 Manual de usuario

Hakko Electronics

Hakko Electronics 936 Manual de usuario

Hakko Electronics

Hakko Electronics FX-888 Manual de usuario

Hakko Electronics

Hakko Electronics 487 Manual de usuario

Manuales populares de Pistola de soldar de otras marcas

Bakon

Bakon 3200 Manual de usuario

Proxxon

Proxxon Gaslotset MGS Manual de usuario

jbc

jbc SFR-A Manual de usuario

jbc

jbc CL8010 Manual de usuario

HAKO

HAKO FX-8804 Manual de usuario

SATA

SATA 02002A Manual de usuario

Velleman

Velleman HRJA151 Manual de usuario

Weller

Weller WSM 1 Manual de usuario

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje

ersa

ersa i-CON 1V Manual de usuario

Weller

Weller WAD 101 Manual de usuario

Weller

Weller WXD 2 Manual de usuario

AlienTek

AlienTek T100 Manual de usuario

Atten

Atten ATETOOL AT-689A Manual de usuario

Surtek

Surtek 112554 Dimensiones y guía de instalación

Parkside

Parkside PLBS 30 A1 Manual de usuario

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manual de usuario

Weller

Weller WX1 Manual de usuario