Haier HSU-09CRA03-HK Manual de usuario

Please read this operation manual before using the air conditioner.

SPLIT TYPE ROOM AIR CONDITIONER

OPERATION MANUAL

HSU-09CRA03-HK

0010517254

HSU-12CRA03-HK

Maximum: D.B/W.B

10.The appliance must be installed on strong enough supporter.

9.Young children should be supervised ensure that they do not play with the appliance.

8. The appliance is not intended to use by young children or infirm persons without supervision.

7. The waste battery should be disposed properly.

6. After installation, the power plug should be easily reached.

5. The wiring method should be in line with the local wiring standard.

4. The distance between the indoor unit and the floor should be more than 2m.

3. If the fuse on PC board is broken please change it with the type of T. 3.15A/250V.

11.The wiring diagram is attached inside the machine.

or a similar qualified person. The type of connecting wire is H05/07RN-F or 245IEC57(YZW).

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent

Cautions

The machine is adaptive in following situation

I. Applicable ambient temperature range:

Cooling Indoor

Outdoor

Maximum: D.B / W.B 32oC/23oC

18oC/14oC

43oC/26oC

18oC

Minimum: D.B / W.B

Minimum: D.B

Parts and Functions

Indoor Unit

OUTLET

INLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

Outdoor Unit

HSU-09CRA03-HK

Inlet grill

Anion generator

Horizontal flap

Inlet

Front panel

Display board

Outlet

Power plug

Vertical blade

(Adgust left and right air flow)

(Adgust up and down air flow.

Don't adgust it manually)

HSU-12CRA03-HK

Actual inlet grille may vary from the one shown in the manual according to

the product purchased

Parts and Functions

Operation

Hints

After replacing with new batteries, remote controller will conduct self-check, displaying

all information on LCD. Then, it will become normal.

NOTE: Cooling only unit do not have displays and functions related with heating

Buttons and display of the remote controller.

FAN

DRY

COOL

AUTO

1. Mode display

2. SWING display

3. FAN SPEED display

4. SLEEP display

5. LOCK display

6. SIGNAL SENDING

7. TIMER OFF display

8. TIMER ON display

9. CLOCK display

10. TEMP display

11. POWER ON/OFF

Used for unit start and stop.

12. MODE

Used to select AUTO run, COOL,

DRY and FAN operation

13. FAN

Used to select fan speed LO, MED, HI, AUTO

14. HOUR

Used to set clock and timer setting.

15. SWING

Used to set auto fan direction.

16. SLEEP

Used to select sleep mode.

17. LOCK

Used to lock buttons and LCD

display.

18. TEMP.SETTING

Used to select your desired temp.

19. SET

Used to confirm timer and clock settings.

20. TIMER

Used to select TIMER ON, TIMER OFF,

TIMER ON-OFF

21. CLOCK

Used to set correct time

22. RESET

normal condition.

Used to reset the controller back to

LO MED HIAUTO

Clock set

When unit is started for the first time and after replacing batteries in remote controller,

clock should be adjusted as follows:

Press CLOCK button, "AM" or "PM" flashes.

Press or to set correct time. Each press will increase or decrease 1min. If the

button is kept depressed, time will change quickly.

After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock

starts working.

ON/OFF

HEALTH

FAN

MODE

SWING

TIMER

CLOCK

SETSLEEP

LOCK RESET

23. HEALTH display

24. HEALTH

Used to operate the healthy function.

110

25. Signal receiver hole

1487

Operation

Remote controller's operation

When in use, put the signal transmission head directly to the

receiver hole on the indoor unit.

The distance between the signal transmission head and the

receiver hole should be within 7m without any obstacle as well.

Don't throw the controller, prevent it from being damaged.

When electronic-started type fluorescent lamp or change-over

type fluorescent lamp or wireless telephone is installed in the

room, the receiver is apt to be disturbed in receivering the signals

so the distance to the indoor unit should be shorter.

Loading of the battery

Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder)

Remove the battery cover:

Slightly press " " and push down the cover.

Load the battery:

Be sure that the loading is in line with the" + "/"-"

pole request as illustrated.

Put on the cover again

Confirmation indicator:

In disorderation, reload the batteries or load the new batteries after 6mins.

Note:

Use two new same-typed batteries when loading.

If the remote controller can't run normally or doesn't work at all,

use a sharp pointed item to press the reset key.

Hint:

Remove the batteries in case unit won't be in usage for a long period.

If there are any display after taking-out just need to press reset key.

Power failure resume(please set and apply as necessary)

If sudden power failure occurs, the unit will resume original operation when power is

supplied again.

Note: When sudden power failure happens during unit operation in power failure resume mode, if

the air conditioner is not desired for use in a long period, please shut off the power supply

in case that the unit automatically resume operation when power is re-supplied, or press

ON/OFF to turn off the unit when power resumes.

(5) Unit stop

(1) Unit start

Auto,Cool，Dry and Fan operation

Press ON/OFF button, unit starts.

ON/OFF

HEALTH

FAN

MODE

TIMER

CLOCK

SETSLEEP

LOCK RESET

SWING

Operation

mode changes as follows:

(2) Select operation mode

Press MODE button. For each press, operation

Unit will run in selected mode.

(4) FAN

Press FAN button. For each press, fan speed changes

as follows:

AUTO LO MED HI

Unit will run at selected fan speed.

Note:AUTO is not available in FAN mode.

Press ON/OFF button.

Note:

Remote controller:

Display board:

2.In DRY mode, when room temperature becomes lower than temp.setting+2oC,

unit will run intermittently at LOW speed regardless of FAN setting.

When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according

to room temperature.

(3) Select temp. setting

Press TEMP button.

Every time the button is pressed, temp. setting increases 1oC

Every time the button is pressed, temp. setting decreases 1oC

Unit will start running to reach the temp. setting on LCD.

In FAN operation mode, the unit will not operate in COOL mode but only in FAN mode ,

AUTO is not available in FAN mode.And temp.setting is disabled.

In FAN mode,SLEEP operation is not available.

AUTO COOL DRY FAN

(BLANK) BLANK

AUTO COOL DRY FAN

Operation

Air Flow Direction Adjustment

1.Status display of air sending

Horizontal flap

( Auto swing )

Pos.4

Remote controON/OFF

HEALTH

FAN

MODE

TIMER

CLOCK

SETSLEEP

LOCK RESET

SWING

ller

Blank

( Downward swing )

Pos.3

( Upward swing )

Pos.2

( Cool/Dry standard position)

Pos.1

2.Up and down air flow direction(Use remote controller)

Move the vertical blade by a knob on air

conditioner to adjust left and right direction

referring to Fig.

3.Left and right air flow adjustment(manual)

For each press of SWING button, air flow direction on remote

controller display as follows according to different operation modes:

Pos.1 Pos.2 Pos.3 Pos.4

The horizontal flap

will swing according to the above positions

Cautions:

Hints

As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more

helpful for a better air circulation.

Do not try to adjust the flap by hand.

When adjusting the flap by hand,turn off the unit ,and use the remote controller to restart the unit.

When humidity is high,condensate water might occur at air outlet if all vertical louvers are

adjusted to left or right.

It is advisable not to keep horizontal flap at downward position for a long time in COOLor DRY

mode ,otherwise, condensate water might occur..

Operation

TIMER Operation

You can let unit start or stop automatically at following times: Before you wake up in the

morning, or get back from outside or after you fall asleep at night.

Set Clock correctly before starting Timer operation

TIMER ON/OFF

Power indicator on indoor unit lights up.

(1)After unit start, select your desired operation mode.

Operation mode will be displayed on LCD.

(3)Timer setting

Press HOUR / button.

Every time the button is pressed, time increases 10 min.

If button is kept depressed, time will change quickly.

Every time the button is pressed, time decreases 10 min.

If button is kept depressed, time will change quickly. Time

will be shown on LCD. It can be adjusted within 24 hours.

Timer mode indicator on indoor unit lights up.

(4)Confirming your setting

After setting correct time, press SET button to confirm, "ON"

or "OFF" stops flashing

Time displayed: Unit starts or stops at x hour x min. (TIMER

ON or TIMER OFF).

To cancel TIMER mode

Just press TIMER button several times until TIMER mode disappears.

Hints

After replacing batteries or a power failure happens, Time setting should be reset.

Remote controller possesses memory function, when use TIMER mode next time, just

press SET button after mode selecting if timer setting is the same as previous one.

TIMER

Every time the button is pressed, display changes as follows:

Select your desired TIMER mode (TIMER ON or

TIMER ON TIMER OFF TIMER ON-OFF

blank

N12:00

12:00

AM 12:00

PM 12:00

TIMER ON-OFF

ON OFF ON/OFF

HEALTH

FAN

MODE

TIMER

CLOCK

SETSLEEP

LOCK RESET

SWING

ON OFF ON OFF

(2)TIMER mode selection

Press TIMER button to change TIMER mode.

OFF), ON or OFF will flash.

TIMER ON-OFF

Operation

TIMER ON-OFF

To cancel TIMER mode

(1)After unit start, select your desired operation mode

Operation mode will be displayed on LCD.

(3)Time setting for TIMER ON

If button is kept depressed, time will change quickly.

Every time the button is pressed, time decreases 10 min.

If button is kept depressed, time will change quickly.

Every time the button is pressed, time increases 10 min.

It can be adjusted within 24 hours.

Time will be shown on LCD.

AM refers to morning and PM to afternoon

Press HOUR button.

(4) Time confirming for TIMER ON

After time setting, press TIMER button to confirm.

"ON" stops blinking, While "OFF" starts blinking.

Time displayed: Unit starts at x hour x min.

(5)Time setting for TIMER OFF

Follow the same procedures in "Time setting for TIMER ON".

(6) Time confirming for TIMER OFF

After time setting, press SET button to confirm, "OFF" stops flashing

Time displayed: Unit stops at X hour X min.

Just press TIMER button several times until TIMER mode disappears.

Every time the button is pressed, display changes as follows:

TIMER ON TIMER OFF TIMER ON-OFF

blank

N12:00

12:00

AM 12:00

PM 12:00

TIMER ON-OFF

ON OFF ON OFF

ON OFF

ON/OFF

HEALTH

FAN

MODE

TIMER

CLOCK

SETSLEEP

LOCK RESET

SWING

(2) Press TIMER button to change TIMER mode.

Select TIMER ON-OFF. "ON" will flash.

Operation

HEALTH Operation

2.Health anion function

Press the ON/OFF switch

1.Unit start

Press the " HEALTH"again, then the healthy function

stops.

The anion generator in the air conditioner can generate a lot of anion

effectively balance the quantity of position and anion in the air and also to

kill bacteria and speed up the dust sediment in the room and finally clean

the air in the room.

Brief introduction to health anion function

3.To Cancel HEALTH Model

is displayed on the remote

HEALTH ON/OFF

FAN

MODE

SWING

TIMER

CLOCK

SET SLEEP

LOCK RESET

Press HEALTH button

controller and is displayed on the display

board .

When indoor fan motor is running, it has healthy

process function. (It's available under any mode)

Otros manuales para HSU-09CRA03-HK

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Acondicionador de aire de Haier

Haier

Haier AS092FCAIA Hoja de especificaciones

Haier

Haier HWR10XC6 - annexe 1 Manual de usuario

Haier

Haier FCE-034BCN2A Manual de usuario

Haier

Haier ESA3059 Manual de instrucciones

Haier

Haier HPR99XC5-C Manual de usuario

Haier

Haier ADH071M1ERG Instrucciones de instalación y funcionamiento

Haier

Haier HSU-18CR03-Y Manual de usuario

Haier

Haier 1U09MADFRA Manual de usuario

Haier

Haier AU282AHBEA Manual de usuario

Haier

Haier HSU18VHK-G Manual de usuario

Haier

Haier AS072XCEAA Manual de usuario

Haier

Haier HSU-09LG03 Manual de usuario

Haier

Haier HWF05XCPT Manual de usuario

Haier

Haier HSU-07HE03/R2 Manual de usuario

Haier

Haier HSU-07HEA03 - annexe 1 Manual de usuario

Haier

Haier ESA3155 - Window Air Conditioner Manual de usuario

Haier

Haier MRV Series Manual de usuario

Haier

Haier AS53HE1HRA Manual de usuario

Haier

Haier GE APPLIANCES USYL24UCDDA Manual de usuario

Haier

Haier 2HUM18HA03/R2 Manual de usuario

Haier

Haier AB072FDAHA Manual de usuario

Haier

Haier H2SM-18RA03 Manual de usuario

Haier

Haier CA0035EAND Manual del propietario

Haier

Haier HSU-09LEA13-W Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario