Haier Arctic Multi 2U20EH2VHA Manual de referencia

Este manual sirve para los siguientes modelos

5

Tabla de contenidos

Otros manuales de Acondicionador de aire de Haier

Haier

Haier HWR08XC7 - annexe 1 Manual de usuario

Haier

Haier HSU-09LF03 Manual de usuario

Haier

Haier HSU-09H03 Manual de usuario

Haier

Haier ESA4089 Manual de instrucciones

Haier

Haier HW-07LN03 Manual de usuario

Haier

Haier HM-05CC03/R1 Manual de usuario

Haier

Haier HBU-14CL03/R1 Manual de usuario

Haier

Haier HW-12LM03 Manual de usuario

Haier

Haier HSU-09HEA03/R2 - annexe 4 Manual de usuario

Haier

Haier AS09GN3ERA Manual de usuario

Haier

Haier HSM-24HEA03-R2 Manual de usuario

Haier

Haier HSU-09LG03 Manual de usuario

Haier

Haier ACD187R Manual de usuario

Haier

Haier 1U24TR4ERA Manual de usuario

Haier

Haier AC-8888-20 Manual de usuario

Haier

Haier HSU-09C03/Z1 Manual de usuario

Haier

Haier SUPER MATCH AS50S2SF1FA-CW Manual de usuario

Haier

Haier HPAC99ER Manual de usuario

Haier

Haier AC122ACERA Manual de usuario

Haier

Haier HSU-18RK03-R2 Manual de usuario

Haier

Haier T-Series Manual de usuario

Haier

Haier AS35S2SF1FA-BH Manual de usuario

Haier

Haier HWS06XCA Manual de usuario

Haier

Haier HSU-09CB13 Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario

DFS05-19

DFS05-19

Multi-Split Communication Wiring Check

The FlexFit Multi and Arctic multi systems are capable of performing a self-test to check

communication wiring between the outdoor to the indoor units. This is a crucial step when performing

start-up on a system as well as performing checks during a service call. It allows you to confirm that

the wiring matches with the associated refrigerant lines for a given circuit.

Arctic Multi 2U20EH2VHA

3U24EH2VHA

FlexFit Multi 3U24MS2VHB

4U36MS2VHB

1

Models affected:

Instructions:

1. Disconnect power to the outdoor unit.

2. Set Dip Switches SW1-1, SW1-2, SW1-3 &

SW1-4 to the ON position. These dip

switches are located on the Service Monitor

Board. (pictured right).

3. Turn ON power to the outdoor unit.

JUNE 2019

Service Bulletin

SW1

Testing Process:

1. All indoor fans will come on at HIGH fan speed.

2. EEV for Circuit A will open.

3. All other EEV’s will close.

4. After a 3 minute delay, the Compressor will start and ramp up to 55HZ.

5. The digital display will alternately display “CH” and “Compressor Frequency (HZ)” at

5-second intervals (pictured below).

6. The system will circulate refrigerant through Circuit Afor about 10 minutes.

7. Afterwards, Circuit A’s EEV will close and Circuit B’s EEV will open.

8. This process will be repeated for each indoor unit that is connected.

2

Service Bulletin

JUNE 2019

DFS05-19

DFS05-19

Testing Process (continued):

9. Once all indoor units have been checked, the digital display will show either “EC” or “0”

•“EC” indicates there is an error in the wires to the indoor unit(s).

•The LED(s) will be flashing, indicating which circuit(s) has the fault.

•For example, if the wires for circuit A and B are switched, then LED1 and

LED 2 will flash.

•Once the wiring is corrected, re-run this test to confirm everything is functional.

o“0”indicates that all wiring is correct.

oIf all the wiring is correct, the LED’s remain solid.

10. Once the test is complete, make sure to change the dip switches back to the OFF

position.And set each indoor unit to preferred set points.

3

Service Bulletin

JUNE 2019

DFS05-19

DFS05-19