Hafele PP9000 Manual de usuario
www.hafele.com
Model PP9000
Digital door lock
* The contents of this user manual are subject to change without prior notice
to the user in order to enhance performance of the products.
PP9000
Installation guide
Contents
Product specification…………………………………………………………………………………...2
Components………….…………………………………………………………………………………3
Prepare for installation………….………………………………………………………………………4
Installation…………………………….…………………………………………………………………5
1
Product specifications
Inside panelOutside panel
2
Mortise Lock
Deadbolt
Shaft socket
Sensor latch
Latch bolt
Touch keypad
CLOSE/OPEN
button
Reset button
Upper cover
Battery cover
Card reader area
Fingerprint sensor
Emergency power port
Reboot button
Key cylinder
Manual open knob
Components
3
14
15
1
10 12 13
2 3 4 5 6 7 8 9
11
1. Upper cover (1 pc)
2. M6 Mounting screw (2 pcs)
3. Inside panel assembly (1pc)
4. Pressure spring (2 pcs)
5. Square shaft (2 pcs)
6. M5 Mounting plate screw (4 pcs)
7. Mounting plate (1 pc)
8. M6 Connecting screw bolt (1 pc)
9. Outside panel assembly (1 pc)
10. Battery cover (1 pc)
11. Mortise lock (1 pc)
12. Mortise mounting screw (2 pcs)
13. M5 Connecting screw bolt (4 pcs)
14. Strike assembly
-Left strike plate (1 pc)
-Right strike plate (1 pc)
-Strike box (1 pc)
15. Mechanical key (2 pcs)
Preparing for installation
4
Check door open direction
This product fits for all door open directions-Left-in/Left-out/Right-in/Right-out
Indoor
Outdoor
Outdoor
Outdoor
Outdoor
Indoor
Indoor
Indoor
Installation
5
1. Mark and drill bores by using the installation
template first, then fix the mortise into the
door frame and tighten the 2 screws to fix the
mortise on the door.
2. Fix 5 screw bolts on the front panel, place
square shaft and pressure spring into the
bore.
M6 Connecting
screw bolt *1 Square shaft
Pressure spring
M5 Connecting
screw bolt *4
Do not make the
mortise deadbolt
come out.
1. Spring: the big end is downward.
2. Select the square shafts and screw bolts with proper
length according to door thickness range.
3. Pass the connection wire through the top bore.
Then align and insert square shaft into mortise
holes to make the front panel against the door
closely.
4. Install the mounting plate with fixing screws
tightly against the door surface.
Installation
6
6. Insert the connecting wires of front panel into
the related sockets of the back panel. Then
align and insert the square shaft into mortise
hole, make the back panel against the door
closely. Finally tighten the 2 fixing screws.
5. Place pressure spring and square shaft in the back
panel in proper order.
Square shaft
Pressure spring
7. Install the batteries, the battery cover and the upper
cover. Then install the striker assembly to finish in-
stallation.
8. please check push-pull handle and mechanical
key if they are working properly.
Upper cover
Battery cover
After installing the striker assembly, please check if the lock
works smoothly by opening/closing door.
Test if mechanical key works smoothly after installation.
Otros manuales para PP9000
1
Tabla de contenidos
Otros manuales de Cerradura de puerta de Hafele
Hafele
Hafele 981.16.100 Manual de usuario
Hafele
Hafele PP8100 Manual de usuario
Hafele
Hafele DT 510 Manual de usuario
Hafele
Hafele DT 600 Manual de usuario
Hafele
Hafele Dialock DT 210 R2 Manual de usuario
Hafele
Hafele DT 700 Manual de usuario
Hafele
Hafele DT 700 Manual de usuario
Hafele
Hafele Series 7000 Manual de usuario
Hafele
Hafele DT 100 FH Manual de usuario
Hafele
Hafele DT 100 Manual de servicio
