Hach PHC28101 Manual de usuario

User Manual DOC022.52.80024

pH Refillable Probe for Low Ionic Strength Samples: Model

PHC28101 or PHC28103

Safety information

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the

instrument could occur if not observed. A symbol on the instrument is referenced in the

manual with a precautionary statement.

Electrical equipment marked with this symbol may not be disposed of in European public disposal systems after

12 August of 2005. In conformity with European local and national regulations (EU Directive 2002/96/EC), European

electrical equipment users must now return old or end-of-life equipment to the Producer for disposal at no charge to

the user.

Note: For return for recycling, please contact the equipment producer or supplier for instructions on how to return end-of-life

equipment, producer-supplied electrical accessories, and all auxiliary items for proper disposal.

Specifications

Note: Specifications are subject to change without notice.

Specifications Details

Probe type Digital combination probe with refillable double junction reference and built-in

temperature sensor

pH range pH 0 to 14

pH resolution User-selectable stabilization time and resolution—Fast: 0.1, Fast: 0.01,

Medium: 0.01, Slow: 0.01 or Slow: 0.001

Slope -59 mV/pH (90 to 110% at 25 °C per Nernstian theoretical value)

Operating temperature range 0 to 50 °C (32 to 122 °F)

Storage temperature range 5 to 40 °C (41 to 104 °F)

Junction Open

Reference type Ag/AgCl

Minimum sample depth 15 mm (0.59 in.)

Dimensions Diameter: 12 mm (0.47 in.)

Length: 175 mm (6.89 in.)

Cable length: 1 or 3 m (3.28 or 9.84 ft)

Cable connection M12 digital output and connector compatible with HQd meters

Product overview

The PHC281 series probe is a pH refillable probe made for difficult samples with a built-in

temperature sensor (Figure 1). The PHC28101 or PHC28103 probe is available with a

1 or 3 m (3.28 or 9.84 ft) cable and is intended for laboratory use. The pH refillable probe

has a high electrolyte flow rate and a large open junction ideal for difficult samples, such

as Low Ionic Strength (LIS), Ultrapure, dirty samples and samples with high solids

content. The probe is not suitable for use with organic solvents. A 59-mL bottle of 2.44 M

KCl Electrode Filling Solution is included with the probe.

Figure 1 Probe overview

1 Probe soaker bottle 4 Protective tape and filling-hole

2 Glass bulb, reference junction and temperature sensor 5 1 or 3 meter (3.28 or 9.84 ft) cable

3 Filling-hole cap 6 Probe soaker bottle holder

Preparation for use

Prepare the probe for use before calibration or sample measurement.

1. Turn the probe soaker bottle cap counter-clockwise to loosen the cap.

2. Remove the soaker bottle from the probe.

3. Rinse the reference junctions and glass bulb with deionized water thoroughly to

remove the viscous storage/filling solution completely. Blot dry with a lint-free cloth.

4. Remove the protective tape from the filling hole before initial use (refer to Figure 1

on page 2). Dispose of the protective tape.

5. Add filling solution to the probe as necessary (refer to Fill the probe on page 10).

The filling solution must be above the standard solution or sample level during

measurement (Figure 2).

6. Make sure that the filling hole is open during measurement for the proper flow of the

filling solution.

Note: For the best stabilization time, condition the probe for several minutes in the sample

before use.

Figure 2 Measurement method

1 Container 3 Filling solution level

2 Probe body 4 Standard solution or sample level

Calibration

Before calibration:

The probe must have the correct service-life time stamp. Set the date and time in the meter before the probe is attached.

It is not necessary to recalibrate when moving a calibrated probe from one HQd meter to another if the additional meter is

configured to use the same calibration options.

To view the current calibration, push , select View Probe Data, then select View Current Calibration.

If any two probes are connected, push the UP or DOWN arrow to change to the single display mode in order to show the

Calibrate option.

Prepare the probe for use (refer to Preparation for use on page 2).

Calibration notes:

•pH buffers can be used in any order. Use buffers that are two pH units apart.

• Additional standard sets along with the minimum number of calibration points can be

selected in the Calibration Options. For a two point calibration, it is recommended that

two buffers be selected: one with a pH above and one with a pH below the expected

sample pH. For a one point calibration, select the buffer nearest to the expected

sample pH.

• The calibration is recorded in the probe and the data log. The calibration is also sent

to a PC, printer or flash memory stick if connected.

• Air bubbles under the sensor tip when submerged can cause slow response or error

in measurement. If bubbles are present, gently shake the probe until bubbles are

removed.

• If a calibration error occurs, refer to Troubleshooting on page 11.

Calibration procedure:

1. Connect the

probe to the

meter. Make sure

that the cable

locking nut is

securely

connected to the

meter. Turn on the

meter.

2. Push

Calibrate. The

display shows the

buffers that are

necessary for

calibration.

3. Prepare the

fresh buffers in

separate beakers

or appropriate

containers.

4. Rinse the

probe with

deionized water.

Blot dry with a lint-

free cloth.

5. Put the probe

in the pH buffer

solution and stir

gently. Make sure

that the reference

junctions are

completely

submerged.

Shake the probe

from side to side

in the standard

solution to refresh

the reference

junction.

6. Push Read.

Stir gently. The

display will show

"Stabilizing" and a

progress bar as

the probe

stabilizes in the

standard. The

display shows the

buffer that has just

been read and

shows the

temperature

corrected pH

value when the

reading is stable.

7. Repeat steps

4 - 6 until the

minimum number

of calibration

points specified in

the current

method have been

collected.

8. Push Done to

view the

calibration

summary. The

display will not

show Done until

the minimum

number of

calibration points

have been

collected.

9. Push Store to

accept the

calibration and go

back to

measurement

mode.

Sample measurement

Before measurement:

The probe must have the correct service-life time stamp. Set the date and time in the meter before the probe is attached.

If complete traceability is necessary, enter a sample ID and operator ID before measurement. Refer to the HQd meter

manual for more information.

Regular calibration is required for the best measurement accuracy (refer to Calibration on page 3).

Prepare the probe for use (refer to Preparation for use on page 2).

Measurement notes:

•Data is automatically stored in the data log when Press to Read or Interval is

selected in the Measurement Mode. When Continuous is selected, data will only be

stored when Store is selected.

• Air bubbles under the sensor tip when submerged can cause slow response or error

in measurement. If bubbles are present, gently shake the probe until bubbles are

removed.

• If a measurement error occurs, refer to Troubleshooting on page 11.

Measurement procedure:

1. Connect the

probe to the

meter. Make sure

that the cable

locking nut is

securely

connected to the

meter. Turn the

meter on.

2. For the best

stabilization time,

condition the

probe in the

sample for at least

10 minutes before

the initial sample

measurement.

3. Rinse the

probe with

deionized water

and then with the

sample. Blot dry

with a lint-free

cloth.

4. Put the probe

in the sample and

stir gently. Make

sure that the

reference

junctions are

completely

submerged. Do

not put the probe

on the bottom or

sides of the

container. Shake

the probe from

side to side in the

sample to refresh

the reference

junction.

5. Push Read.

The display will

show "Stabilizing"

and a progress

bar as the probe

stabilizes in the

sample. The

display will show

the lock icon when

the reading

stabilizes.

6. Repeat steps

2-4 for additional

measurements.

7. When

measurements

are done, store

the probe (refer to

Storage

on page 10).

Run a check standard

The run check standard feature validates instrument performance between sample

measurements. Use the run check standard feature for periodic or user-defined interval

measurements of a traceable standard solution. Set the criteria for check standards from

the PHC281 Settings menu.

Note: Access control must be off or a valid password must be entered before any of the check

standard method options can be changed.

1. Push . The Full Access Options menu is shown.

2. Select Run Check Standard.

Note: Select the correct probe if two probes are connected to the meter.

3. Get the standard solution shown on the display.

4. Rinse the probe with deionized water. Blot dry with a lint-free cloth.

5. Put the probe in the standard solution until the temperature sensor is completely

submerged. Move the probe up or down or gently tap on the beaker to remove air

bubbles from the probe.

6. Push Read. The display will show "Stabilizing" and a progress bar as the reading

stabilizes. The display shows the value of the check standard and either Check

Standard Passed or Check Standard Failed.

7. If the display shows Check Standard Passed, the check standard measurement is

within the accepted limits set by the administrative user. Select Done to continue with

the sample measurement.

8. If the display shows Check Standard Failed, the measurement is outside of

accepted limits set by the administrative user and a recalibration is recommended. If

the acceptance criteria is set to Cal Expires on Failure: Yes, the display shows the

calibration icon and a question mark until the probe is recalibrated. To correct the

probe calibration and status indicator, calibrate the probe (refer to Calibration

on page 3).

Advanced operation

Parameter-specific settings can be changed through the Full Access Options menu.

Details about menu navigation, available options and how to change them are given in

the screens, tables and procedures throughout this section.

The settings that can be changed are shown in Table 1.

Table 1 Parameter-specific settings

Setting Options

Measurement Options • Resolution

•Upper and lower range limits

Calibration Options • Buffer set

• Buffer set values (if Custom Buffer Set selected)

• Reminder

• Minimum Cal points

• Slope limit

Check Standard Options • Standard (temperature compensated buffer or custom at 25 °C)

• Reminder

• Acceptance criteria

• Standard value at 25 °C (if custom standard selected)

Units • pH

• mV

Change measurement options

Methods are groups of default or user-defined settings relevant to specific applications. If

the meter is set to the default method and the Modify Current Settings option is chosen, a

prompt for a new name is shown after the changes are entered. The settings are saved

with this name to distinguish them from the default method settings, which cannot be

changed. A saved method can be used instead of multiple adjustments to the individual

settings. Changes made to a user-defined method are automatically saved with the

existing name. Multiple methods can be saved for the same probe on each meter.

1. Make sure a probe is connected to the meter.

2. Push and select PHC281 Settings.

3. Select Modify Current Settings.

4. Select Units. Select pH (default) or mV.

Note: The mV option can be used to find the probe offset in a pH 7 buffer or to measure the

slope. Both units are shown when the detail display mode is selected.

5. Select Measurement Options and update the settings:

Option Description

Resolution Sets the resolution:

•0.1pH—Fast

• 0.01pH—Fast (default)

• 0.01pH—Medium

• 0.01pH—Slow, or

• 0.001pH—Slow

The resolution affects the number of decimal places and the stabilization

time. Higher resolution measurements take more time to stabilize. Slower

stabilization times provide higher accuracy measurements.

Measurement

Limits

Set the measurement limits—Lower limit (default: 0.00 pH) or Upper limit

(default: 14.00 pH).

The measurement limits can be set to match the acceptable values for the

sample. When the measurement is above the upper limit setting or below

the lower limit setting, the meter shows an "Out of limits" message. This

message is an alert to a potential problem with the process conditions.

6. If prompted, enter a name for the new method settings. Additional changes made to

the settings of an existing method are automatically saved with the same method

name.

7. Push EXIT until the meter returns to the measurement mode.

Change calibration options

1. Make sure a probe is connected to the meter.

2. Push and select PHC281 Settings.

3. Select Modify Current Settings.

4. Select Calibration Options and update the settings:

Option Description

Buffer Set Sets the temperature compensated buffer set used for calibration—

•Color Coded—4.01, 7.00, 10.01 (default)

• IUPAC—4.01, 7.00, 10.01, 12.45

• DIN—4.65, 9.23

• IUPAC—4.01, 6.86, 10.01, 12.45

• IUPAC—4.01, 6.86, 9.18, 12.45

• IUPAC—4.01, 7.00, 9.18, 12.45

• Custom Buffer Set (refer to Table 2)

Custom buffer sets are characterized at 25 °C (77 °F).

Buffer set values are shown on the Calibration Options screen.

Note: Only the minimum calibration points must be measured for DONE to

be shown on the calibration screen.

Buffer Set

Values

If the Buffer Set is set to Customer Buffer Set, sets the custom buffer set

(refer to Table 2).

Minimum Cal

Points

Sets the minimum number of calibration points necessary before a

calibration can be completed—1 (default), 2 or 3.

Slope Limit Sets the slope limit—1% to 10% (acceptable slope criteria, default = 5%).

The slope must fall within set limits for successful calibration.

5. Select Calibration Reminder and update the settings:

Option Description

Reminder

Repeat

Meter will make an audible sound when a calibration is due and repeat the

sound at the selected interval—Off (default), 2 h, 4 h, 8 h, 2 d, 5 d or 7 d.

Expires Calibration expires after the selected time—Immediately, Reminder +

30 min, Reminder + 1 h, Reminder + 2 h or Continue Reading.

Note: The meter cannot be used to read samples after calibration has

expired unless Continue Reading is selected.

6. If prompted, enter a name for the new method settings. Additional changes made to

the settings of an existing method are automatically saved with the same method

name.

7. Push EXIT until the meter returns to the measurement mode.

Table 2 Custom buffer set

Buffer set values Option Description

Std1

Std2

Std3

Std4

Std5

1.09pH—25 °C Pre-set temperature compensated buffer values.

Note: Selected standards must differ by a minimum of 2 pH units. For example, if 1.09 pH is

chosen for the first standard, the second standard must differ by at least 2 pH. Standards that do

not meet this minimum will appear gray on the screen and will not be selectable.

1.68pH—25 °C

4.01pH—25 °C

4.65pH—25 °C

6.86pH—25 °C

7.00pH—25 °C

9.18pH—25 °C

9.23pH—25 °C

10.01pH—

25 °C

12.45pH—

25 °C

Custom Buffer Custom buffer value.

Range = 2.000 pH to 14.000 pH.

Custom buffer values are not temperature compensated. Custom buffers should be read

at 25 °C.

No Buffer Standard is undefined when this option is selected.

Change check standard options

1. Make sure a probe is connected to the meter.

2. Push and select PHC281 Settings.

3. Select Modify Current Settings.

4. Select Check Standards Options and update the settings:

Option Description

Standard Sets the temperature compensated buffer value for check standard—

•4.01pH—25 °C

• 4.65pH—25 °C

• 6.86pH—25 °C

• 7.00pH—25 °C

• 9.18pH—25 °C

• 9.23pH—25 °C

• 10.01pH—25 °C

• 12.45pH—25 °C

• Custom

The standard value is shown on the Check Standard Options screen.

No temperature compensation for custom buffers.

Standard

Value

When Standard is set to Custom, enter the standard value using the up/down

arrow keys.

5. Select Check Standard Reminder and update the settings:

Option Description

Reminder Repeat Sets the time interval for the check standard reminder—Off, 30 minutes,

2 h, 4 h, 8 h, 12 h or 24 h.

Allow Defer Allows the postponement of check standard reminders—Yes or No.

6. Select Acceptance Criteria and update the settings:

Option Description

Acceptance Limits Sets the tolerance limits for check standard—0.005pH (default) to

1.000pH.

Cal Expires on Failure Recalibration required if check standard fails—Yes or No.

7. If prompted, enter a name for the new method settings. Additional changes made to

the settings of an existing method are automatically saved with the same method

name.

8. Push EXIT until the meter returns to the measurement mode.

Maintenance

Clean the probe

Clean the probe when:

•Drifting/inaccurate readings occur as a result of contamination on the glass sensor or

the probe being left dry for extended periods of time.

• Slow stabilization time occurs as a result of contamination on the glass sensor.

• A calibration error occurs as a result of contamination on the glass sensor.

For general contaminants:

1. Rinse the probe with deionized water and blot dry with a lint-free cloth.

2. Soak the glass bulb for 12 to 16 hours in Hach Electrode Cleaning Solution.

3. Rinse or soak the probe for 1 minute in deionized water.

4. Soak the probe in pH 4 buffer for up to 20 minutes, then rinse with deionized water.

5. Blot dry with a lint-free cloth.

For fats, grease and oils:

1. Soak the glass bulb in a warm detergent solution for up to 2 hours.

2. Rinse or soak the probe for 1 minute in deionized water.

3. Soak the probe in pH 4 buffer for up to 20 minutes, then rinse with deionized water.

4. Blot dry with a lint-free cloth.

Fill the probe

To add filling solution to the probe:

1. If the filling hole is closed, remove the filling-hole cap from the filling hole (refer to

Figure 1 on page 2).

2. Remove the cap from the tip of the filling solution bottle.

3. Hold the bottle so that the tip is down. Put the tip of the bottle in the filling hole.

4. Slowly squeeze the bottle and fill the probe completely.

Note: Fill the probe completely for the best performance.

5. If the probe will not be used immediately, store the probe (refer to Storage

on page 10).

6. Keep the filling solution bottle and cap for later use.

Note: If the dispensing tip becomes clogged, remove the dispensing tip and soak the tip in

warm water. Dry thoroughly and assemble.

Storage

For the best probe performance, do not let the reference junction dry out.

Short-term and long-term storage

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento analítico de Hach

Hach

Hach Lange ORBISPHERE 3100 Manual rápido

Hach

Hach Polymetron 9582sc Manual de usuario

Hach

Hach 9586sc Manual rápido

Hach

Hach PHOSPHAX indoor sc Manual de usuario

Hach

Hach ORBISPHERE 32301 Manual rápido

Hach

Hach NV3300 Manual de usuario

Hach

Hach sension8 Manual de usuario

Hach

Hach Polymetron 9611sc PO4 3- Manual de usuario

Hach

Hach CL17sc Manual de usuario

Hach

Hach Polymetron 9610sc SiO2 Manual de usuario

Hach

Hach Polymetron 9526 Manual rápido

Manuales populares de Instrumento analítico de otras marcas

Cocraft

Cocraft NLT04 Manual de usuario

M&C

M&C GENTWO PMA1000 Manual de usuario

MICRO-EPSILON

MICRO-EPSILON optoncdt 1700 Manual de usuario

CONDTROL

CONDTROL XP4 PRO Manual de usuario

Extech Instruments

Extech Instruments BR200 Manual de usuario

Dewetron

Dewetron DEWE-30-16 Manual del producto

EXTOL PREMIUM

EXTOL PREMIUM 8820043 Instrucciones de instalación y funcionamiento

RIDGID

RIDGID SeeSnake Compact Manual de usuario

Teledyne

Teledyne 3000PA Manual de usuario

YDLIDAR

YDLIDAR TIA Manual de usuario

Olympus

Olympus IPLEX FX Series Manual de usuario

Bosch

Bosch GLM 50 C Professional Manual de usuario

Reflecta

Reflecta DigiEndoscope Manual de usuario

Chinavision

Chinavision CVACZ-G696 Instrucciones de montaje

Fuji Electric

Fuji Electric ZKMA Manual de usuario

Teledyne

Teledyne 3300TA Manual de usuario

VOLTCRAFT

VOLTCRAFT IC-100HD Manual de usuario

RIDGID

RIDGID micro CA-25 Manual de usuario