H3C LSXM1BSR Manual de usuario

Manual version: 6PW102-20170317 BOM: 3105A03T

i

H3C LSXM1BSR 1U Bottom-Support Rails Installation

Guide

1 Introduction

The H3C LSXM1BSR 1U adjustable bottom-support rails can be adjusted in the range of 630 mm

(24.80 in) to 900 mm (35.43 in).

The bottom-support rails are applicable only to four-post racks. To attach the bottom-support rails to

a rack, make sure the rack depth is in the length range of the bottom-support rails.

2 Installation procedures

WARNING!

To avoid bodily injury, keep the bottom-support rail horizontal and hold the front and rear endsof the

bottom-support rail when you unpack and install a bottom-support rail.

The bottom-support rail installation might vary by rack type. The following installation procedure is for

your reference only.

To install the bottom-support rails:

1. Read the signs on the bottom-support rails to avoid making a mistake.

Figure 1 Left bottom-support rail

(1) Bottom-support rail installation hole (2) Sign

(3) Guide rail (4) Front plate installation hole

(5) Locating tab

2. Mark the bottom-support rail installation position on the mounting rails:

The bottom-support rails are installed in the 1 RU region below the device.

a. As shown in Figure 2, align the installation holes in the bottom-support rail with the

uppermost and lowermost standard square holes in the 1 RU region on the mounting rail.

The bottom-support rail has a locating tab on the front and rear ends. You can also align the

locating tab with the auxiliary installation hole in the 1 RU region on the mounting rail.

Figure 2 uses the right bottom-support rail and the right front mounting rail.

Manual version: 6PW102-20170317 BOM: 3105A03T

ii

b. Mark the lowermost standard square hole in the 1RU region on the mounting rail.

c. Mark the standard square holes at the same height on the other three mounting rails.

Figure 2 Locating the bottom-support rail installation holes

(1) Auxiliary installation hole (2) Standard square hole for installing the bottom-support rail

3. Install cage nuts on the uppermost and lowermost standard square holes in the marked 1 RU

region on each mounting rail, as shown in Figure 3.

You need to install a total of eight cage nuts.

Figure 3 Installing a cage nut

4. Attach the bottom-support rails to the rack:

a. Place the right bottom-support rail at the marked position in the rack. Hold both ends of the

right bottom-support rail to compress it so that the locating tabs at both ends of the

bottom-support rail are inserted into the auxiliary installation holes in the mounting rails.

b. Use screws to secure the bottom-support rail to the mounting rails.

c. Perform the same steps to install the left bottom-support rail. Make sure the two

bottom-support rails are at the same height so the device can be placed horizontally.

Install a screw in each mounting hole of the bottom-support rail. You need to install a total of

eight M6 screws.

Manual version: 6PW102-20170317 BOM: 3105A03T

iii

Figure 4 Attaching the bottom-support rail to the mounting rails

(1) Compress the bottom-support rail, making sure both ends of the bottom-support rail are attached to the

mounting rails.

(2) Install screws

5. Attach the front plate to the rack:

a. Orient the front plate so that the front of the plate faces outward. Figure 5 shows the rear of

a front plate.

Figure 5 Rear of a front plate

(1) Installation hole

b. Align the installation holes in the front plate with the front plate installation holes in the

bottom-support rails, and fasten the screws.

Two M4 screws are required to secure the front plate to the rack.

1

2

Manual version: 6PW102-20170317 BOM: 3105A03T

iv

Figure 6 Installing the front plate

Copyright © 2015-2017 New H3C Technologies Co., Ltd.

Tabla de contenidos

Otros manuales de Servidor de H3C

H3C

H3C UniServer BT716F Manual de usuario

H3C

H3C UniServer R4900 G3 Manual de usuario

H3C

H3C XE 200 IP Manual de usuario

H3C

H3C UniServer R6900 G5 Manual de operación y mantenimiento

H3C

H3C UniServer R6700 G3 Manual de operación y mantenimiento

H3C

H3C UniServer R2700 G3 Manual de usuario

H3C

H3C UniServer R2900 G3 Manual de operación y mantenimiento

H3C

H3C UniServer R4900 G3 Manual de usuario

H3C

H3C UniServer R4900 G3 Manual de usuario

H3C

H3C UniServer R6900 G3 Manual de operación y mantenimiento

H3C

H3C UniServer R6700 G3 Manual de usuario

H3C

H3C UIS-Cell 3000 G3 Manual de usuario

H3C

H3C UniServer R4700 Manual de operación y mantenimiento

H3C

H3C UniServer R6900 Manual de operación y mantenimiento

H3C

H3C UniServer B5700 G5 Manual de usuario

H3C

H3C UniServer T1100 G3 Manual de usuario

H3C

H3C UniServer R4900 G5 Manual de operación y mantenimiento

H3C

H3C UniServer R4900 G5 Guía del usuario

H3C

H3C UniServer R4300 G3 Manual de operación y mantenimiento

H3C

H3C MS8000 Manual de usuario

H3C

H3C SecPath L5030 Manual de operación y mantenimiento

H3C

H3C UniServer R6900 G5 Manual de usuario

H3C

H3C UniServer R6900 G3 Manual de usuario

H3C

H3C UniServer B5800 G3 Manual de usuario

Manuales populares de Servidor de otras marcas

HP

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario