H3C H3C SecPath F1800-A Manual de usuario

Installation Manual

H3C SecPath F1800-A Firewall Table of Contents

Table of Contents

Chapter 3 Installation....................................................................................................................3-1

3.1 Installation Flow.................................................................................................................3-1

3.2 Mounting a SecPath to a Specified Place .........................................................................3-2

3.2.1 Mounting a SecPath into the Rack..........................................................................3-2

3.2.2 Mounting a SecPath onto the Workbench ..............................................................3-3

3.3 Connecting the PGND.......................................................................................................3-4

3.4 Connecting Power Cable...................................................................................................3-5

3.4.1 Connecting AC Power Cable ..................................................................................3-5

3.4.2 Connecting DC Input Power Cable.........................................................................3-6

3.5 Connecting the Console Terminal .....................................................................................3-7

3.6 Connecting the SecPath to a LAN..................................................................................... 3-9

3.7 Connecting the SecPath to a WAN..................................................................................3-10

3.8 Installation Verification.....................................................................................................3-12

Installation Manual

H3C SecPath F1800-A Firewall Chapter 3 Installation

3-1

Chapter 3 Installation

3.1 Installation Flow

Start

Mountthe cabinet(optional)

Mountthe equipmentto the

specified location

Connectthe PGND wire

Connectthe power cord

Connectthe equipmentto

the console terminal

Install interface module

Connectthe equipmentto

the Ethernet

Connectthe equipmentthe

the WAN

Verifyinstallation

Poweron the equipment

Normal?

Yes

Fnd

No Turn off the power switch

Trouble shooting

Figure 3-1 Installation flow

Installation Manual

H3C SecPath F1800-A Firewall Chapter 3 Installation

3-2

Caution:

Before installing a SecPath, make sure that:

zYou have read Chapter 2 carefully.

zWhat described in Chapter 2 has been met.

3.2 Mounting a SecPath to a Specified Place

3.2.1 Mounting a SecPath into the Rack

 Note:

The SecPath can be mounted in N68 cabinet provided by Huawei-3Com.

For N68 cabinet installation in detail, refer to “N68 Cabinet Installation”.

The SecPath is designed to fit the 19-inch standard rack.

Its dimensions are 436.2 mm (Width) ×420 mm (Depth) ×130.5 mm (Height).

Its weight is 20 kg with full configuration.

Follow the steps below to mount a SecPath.

Step 1: Make confirmation before mounting.

Ensure the rack has been well fixed. The installation position for the SecPath has

been well arranged and there is no obstacle inside the rack or around.

Ensure the equipment is ready for installation and has been placed near the rack,

where the equipment can be moved easily.

Step 2: Install chassis brackets.

Fix the brackets to both sides of the chassis with M3 screw by a cross screwdriver and

remove cable holder on brackets, as shown in Figure 3-2.

Installation Manual

H3C SecPath F1800-A Firewall Chapter 3 Installation

3-3

Figure 3-2 Installing the brackets

Step 3: Mount the equipment to the rack.

1) Lift the SecPath a little higher than the shelf or guides in the rack;

2) Put the SecPath on the shelf or guides;

3) Push it into the rack.

Step 4: Fix the equipment to the rack.

Fix the equipment to the rack with M3 screw through brackets, as shown in Figure 3-3.

1. rack 2. Mounting brackets (without cabling racks) 3. Mounting screws

4. SecPath1000 5. Guides

Figure 3-3 Installing the SecPath into a rack

3.2.2 Mounting a SecPath onto the Workbench

In most cases, the SecPath is often placed on a clean bench. This mounting method

is simple.

Installation Manual

H3C SecPath F1800-A Firewall Chapter 3 Installation

3-4

You should ensure:

zKeep the workbench stable and the PGND cable is well grounded.

zLeave the at least 10 cm space around the chassis for heat dissipation.

zDo not put heavy objects on the chassis.

3.3 Connecting the PGND

Warning:

The proper connection of the PGND wire is the essential safeguard against:

zLightning shocks

zInterference

Therefore, you must first correctly connect the PGND wire when installing and using

the SecPath; otherwise, the SecPath and the peer equipment may be damaged.

The SecPath provides a separate PGND screw. You must properly connect the PGND

to the ground. In this way, you can ensure the faradism and leakage power to be

channeled into the earth ground. As a result, the anti-EMI capability of the entire

SecPath can be improved.

The PGND also provides protection against the high voltage of lightning shocks

caused by external network lines like E1/T1 line and ISDN/PSTN line.

The PGND screw is located at top right rear of the chassis and identified by a

grounding mark “ ”, as shown in Figure 3-4.

1. Grounding screw

Figure 3-4 PGND grounding screw

Installation Manual

H3C SecPath F1800-A Firewall Chapter 3 Installation

3-5

Connect the ground screw to the grounding bar using a PGND cable. It is required

that a grounding resistance should be less than 5 ohm. If you install the SecPath in a

19-inch standard rack, you must also ground the rack.

3.4 Connecting Power Cable

The SecPath supports:

zAC input power supply module

zDC input power supply module

You can choose one from them as needed. Both of them are the same in terms of

features and functions, except for the PWR type.

3.4.1 Connecting AC Power Cable

I. AC Input Power Supply

AC power input range: 90 to 264VAC, 50/60Hz.

Figure 3-5 showsAC input power socket.

1. Cable-retention clip 2. AC input

3. Power switch

Figure 3-5 Partial appearance of AC power socket

II. Recommended AC Power Socket

You should use a 3-line single-phase power socket with a grounding terminal, which

should be reliably connected to the ground in the building.

Normally, the grounding terminal of the power supply system in a building was buried

in the ground during theconstruction and cabling. You must make sure that the power

Installation Manual

H3C SecPath F1800-A Firewall Chapter 3 Installation

3-6

supply for the building has been well grounded before connecting the AC power

cable.

III. Connecting AC Power Cable

Step 1: Check that the PGND wire has been properly connected to the ground.

Step 2: Make sure that the power switch is in the OFF position. Insert one end of the

power cable into the power socket on the rear panel, and fix the cable onto the

cable-retention clip with a cable strap. Connect the other end of the cable to the AC

power socket.

Step 3: Place the power switch to the ON position.

Step 4: Check that the power LED on the front panel is ON, which means the power

cable is correctly connected.

3.4.2 Connecting DC Input Power Cable

I. DC Input Power Supply

DC power input range: -36 to -72V DC.

Figure 3-6 shows the DC input power socket.

1. Power switch 2. DC input

Figure 3-6 Partial appearance of DC power socket

II. Connecting DC Power Cable

Figure 3-7 DC power cable

Installation Manual

H3C SecPath F1800-A Firewall Chapter 3 Installation

3-7

Table 3-1 DC power cable pinouts

-48 power supply side SecPath side

X2 (blue -48V lead) X1.A1

X3 (black BGND lead) X1.A3

Step 1: Check that the PGND wire has been properly connected to the ground.

Step 2: Make sure that the power switch is in the OFF position. Connect one end of

the DC power cable to the power socket on the rear panel of the equipment chassis

and the other end to the –48V DC power supply.

Warning:

Read the label on the cable carefully before connecting the DC power cable. Thus,

you will not make mistakes.

Step 3: Place the power switch to the ON position.

Step 4: Check that the POWER LEDon the front panel is ON, which means the power

cable is correctly connected.

3.5 Connecting the Console Terminal

The SecPath provides an EIA/TIA-232 asynchronous serial console interface,

through which you can configure the SecPath.

For the console interface attributes, refer to Section 1.4.

I. Console Cable

The console cable is an 8-core shielded cable.

At one end of the cable is a crimped RJ-45 connector that is to be plugged into the

console interface of the SecPath; at the other end of the cable are a DB-9 (female)

connector and a DB-25 (female) connector.

You can plug either of them into the serial port on the console terminal as needed.

Figure 3-8 shows the console cable.

Installation Manual

H3C SecPath F1800-A Firewall Chapter 3 Installation

3-8

Figure 3-8 Console cable

For the pinouts of the console cable, refer to “AppendixA.1”.

II. Connecting Console Cable

Before you configure the SecPath at the console terminal, connect the console cable

in the following steps:

Step 1: Select a console terminal.

The console terminal can be:

zStandard ASCII terminal fit with an RS-232 serial port

zRegular PC

The latter is often used.

Step 2: Connect the cable.

1) Power off the SecPath and the console terminal;

2) Connect the RS-232 serial port to the console interface on the RPU through a

console cable.

Power on the SecPath after checking the installation; if the SecPath is working

normally, the system will display the equipment boot information on the console

terminal.

For details, refer to Section 1.4.3.

Installation Manual

H3C SecPath F1800-A Firewall Chapter 3 Installation

3-9

3.6 Connecting the SecPath to a LAN

I. Introduction to the Ethernet Interface

The SecPath provides the fixed 10/100Base-TX FE interface.

For its attributes in detail, refer to the section “1.4.1 RPU".

II. Ethernet Cable

The 10/100Base-TX Ethernet interface usually adopts the category 5 twisted-pair for

connection, as shown in Figure 3-9.

Figure 3-9 Ethernet cable

Ethernet cables fall into two categories:

zStraight-through cable

The wire sequences of the twisted pairs crimped in the RJ-45 connectors at both ends

are the same. It is used to connect a terminal device, such as PC and the SecPath to

a hub or LAN switch. The cables delivered with the equipment are straight-through

cables.

zCrossover cable

The wire sequences of the twisted pairs crimped in the RJ-45 connectors at both ends

are different. It is used to connect two terminal devices, such as PC and the SecPath.

Users can make it as needed.

For the pinouts of the cables and the making procedures, refer to “AppendixA”.

Note:

zThe standard equipping package of the SecPath has included the interface cables

for the fixed Ethernet interfaces.

zWhen preparing network cables, use shielded twisted-pair (STP) cables. In this

way, they are available for the sake of electromagnetic compatibility.

Otros manuales para H3C SecPath F1800-A

Tabla de contenidos

Otros manuales de Cortafuegos de H3C

H3C

H3C SecPath F5000-A5 Manual de usuario

H3C

H3C SecPath F10 0 Series Manual de usuario

H3C

H3C H3C SecPath F1800-A Manual de usuario

H3C

H3C H3C SECPATH F100-A Manual de usuario

H3C

H3C SecPath F5020 Manual de usuario

H3C

H3C SecPath F100-C Manual de usuario

H3C

H3C H3C SecPath F1800-A Manual de usuario

H3C

H3C LSUM1FWCEAB0 Manual de usuario

H3C

H3C SecPath F100-C-EI Manual de usuario

H3C

H3C H3C SECPATH F1000-S Manual de usuario

H3C

H3C SecPath F10X0 Manual de usuario

H3C

H3C SecPath F1000-E Manual de usuario

H3C

H3C SecPath F5030 Manual de usuario

H3C

H3C SecPath F100-X-G3 Manual de usuario

H3C

H3C SecPath F5030 Manual de usuario

H3C

H3C SecPath M9000-S NSQM2FWDFG0 Manual de usuario

H3C

H3C SecPath F5020 Manual de usuario

H3C

H3C SecPath Series Manual de instalación

H3C

H3C SecPath F50X0-D Series Manual de instalación

H3C

H3C SecPath F1000-AI-5 Series Manual de usuario

H3C

H3C SecPath NSQM1F1KGM0 Manual de usuario

H3C

H3C SecPath F5000-AI-15 Manual de usuario

H3C

H3C SecPath F5030 Manual de usuario

H3C

H3C SecPath F5000 Series Manual de instrucciones

Manuales populares de Cortafuegos de otras marcas

Cisco

Cisco S190 Manual de usuario

Fortinet

Fortinet FortiGate Voice Series Manual de usuario

ADTRAN

ADTRAN NetVanta 2300 Manual de usuario

SecureLogix

SecureLogix ETM System Manual de usuario

NETGEAR

NETGEAR ProSafe FVX538 Manual de usuario

Lanner

Lanner FW-8877 Manual de usuario

Huawei

Huawei USG6000 Series Manual de instalación y operación

Nexcom

Nexcom DNA 1150 Manual de usuario

Fortinet

Fortinet FortiGate-60 series Manual de usuario

Cisco

Cisco 3110 Manual

Draytek

Draytek Vigor2860 Series Manual de usuario

Lanner electronics

Lanner electronics FW-7650 Series Manual de usuario

Swisscom

Swisscom Internet Backup Manual de usuario

SonicWALL

SonicWALL NSa 5700 Manual de usuario

DPtech

DPtech FW1000 SERIES Manual de usuario

FEITIAN

FEITIAN MultiPass FIDO Manual de usuario

EBLOCKER

EBLOCKER PRO Manual de usuario

GTA

GTA GB-200 Manual de usuario