GW Instek PSU Series Manual del propietario

Programmable DC Power Supply

PSU Series

PROGRAMMING MANUAL

ISO-9001 CERTIFIED MANUFACTURER

All manuals and user guides at all-guides.com

all-guides.com

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

rights to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.

All manuals and user guides at all-guides.com

Table of Contents

SAFETY INSTRUCTIONS .................................................. 4

GETTING STARTED.......................................................... 8

PSU Series Overview .............................. 9

Appearance .......................................... 14

Configuration Settings ......................... 22

REMOTE CONTROL ....................................................... 32

Interface Configuration ........................ 34

Command Syntax ................................. 63

Command List ..................................... 67

Status Register Overview ................... 127

Error List ........................................... 140

APPENDIX ....................................................................149

PSU Default Settings ......................... 149

Error Messages & Messages .............. 151

LED ASCII Table Character Set ........... 153

INDEX ..........................................................................154

All manuals and user guides at all-guides.com

PSU Programming Manual

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow during

operation and storage. Read the following before

any operation to insure your safety and to keep

the instrument in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the

instrument.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the PSU or to other

properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

All manuals and user guides at all-guides.com

SAFETY INSTRUCTIONS

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased.

Safety Guidelines

General

Guideline

CAUTION

Do not place any heavy object on the PSU.

Avoid severe impact or rough handling that

leads to damaging the PSU.

Do not discharge static electricity to the PSU.

Use only mating connectors, not bare wires, for

the terminals.

Do not block the cooling fan opening.

Do not disassemble the PSU unless you are

qualified.

(Measurement categories) EN61010-1:2010 and EN61010-2-030

specifies the measurement categories and their requirements as

follows. The PSU falls under category II.

Measurement category IV is for measurement performed at the

source of low-voltage installation.

Measurement category III is for measurement performed in the

building installation.

Measurement category II is for measurement performed on the

circuits directly connected to the low voltage installation.

0 is for measurements performed on circuits not directly

connected to Mains.

Power Supply

WARNING

AC Input voltage range: 85Vac~265Vac

Frequency: 47Hz to 63Hz

To avoid electrical shock connect the protective

grounding conductor of the AC power cord to

an earth ground.

All manuals and user guides at all-guides.com

PSU Programming Manual

Cleaning the PSU

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid.

Do not use chemicals containing harsh material

such as benzene, toluene, xylene, and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Relative Humidity: 20%~ 85% (no condensation)

Altitude: < 2000m

Temperature: 0°C to 50°C

(Pollution Degree) EN61010-1:2010 and EN61010-2-030 specifies

the pollution degrees and their requirements as follows. The PSU

falls under degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of dielectric

strength or surface resistivity”.

Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

Pollution degree 2: Normally only non-conductive pollution

occurs. Occasionally, however, a temporary conductivity caused

by condensation must be expected.

Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment

is normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature

nor humidity is controlled.

Storage

environment

Location: Indoor

Temperature: -25°C to 70°C

Relative Humidity: ≤90%(no condensation)

Disposal

Do not dispose this instrument as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased. Please make sure

discarded electrical waste is properly recycled to

reduce environmental impact.

All manuals and user guides at all-guides.com

all-guides.com

SAFETY INSTRUCTIONS

Power cord for the United Kingdom

When using the power supply in the United Kingdom, make sure

the power cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

As the colours of the wires in main leads may not correspond with

the coloured marking identified in your plug/appliance, proceed

as follows:

The wire which is coloured Green & Yellow must be connected to

the Earth terminal marked with either the letter E, the earth symbol

or coloured Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the

terminal marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment

or contact the supplier.

This cable/appliance should be protected by a suitably rated and

approved HBC mains fuse: refer to the rating information on the

equipment and/or user instructions for details. As a guide, a cable

of 0.75mm2should be protected by a 3A or 5A fuse. Larger

conductors would normally require 13A types, depending on the

connection method used.

Any exposed wiring from a cable, plug or connection that is

engaged in a live socket is extremely hazardous. If a cable or plug is

deemed hazardous, turn off the mains power and remove the cable,

any fuses and fuse assemblies. All hazardous wiring must be

immediately destroyed and replaced in accordance to the above

standard.

All manuals and user guides at all-guides.com

PSU Programming Manual

GETTING STARTED

This chapter describes the power supply in a

nutshell, including its main features and front /

rear panel introduction. After going through the

overview, please read the theory of operation to

become familiar with the operating modes,

protection modes and other safety considerations.

PSU Series Overview.................................................. 9

Series lineup ........................................................................................ 9

Main Features ...................................................................................10

Accessories ........................................................................................11

Appearance.............................................................. 14

PSU Series Front Panel...................................................................14

PSU Series Display and Operation Panel ....................................17

Rear Panel..........................................................................................19

Configuration Settings ............................................. 22

Setting Normal Function Settings.................................................22

Setting Power On Configuration Settings ...................................24

Configuration Table.........................................................................26

All manuals and user guides at all-guides.com

GETTING STARTED

PSU Series Overview

Series lineup

The PSU series consists of 10 models, covering a number of

different current, voltage and power capacities:

Model name

Voltage Rating1

Current Rating2

Power

PSU 6-200

200A

1200W

PSU 12.5-120

12.5V

120A

1500W

PSU 20-76

20V

76A

1520W

PSU 40-38

40V

38A

1520W

PSU 60-25

60V

25A

1500W

PSU 100-15

100V

15A

1500W

PSU 150-10

150V

10A

1500W

PSU 300-5

300V

1500W

PSU 400-3.8

400V

3.8A

1520W

PSU 600-2.6

600V

2.6A

1560W

1Minimum voltage guaranteed to 0.2% of rating voltage.

2Minimum current guaranteed to 0.4% of rating current.

All manuals and user guides at all-guides.com

PSU Programming Manual

Main Features

Performance

High power density: 1500W in 1U

Universal input voltage 85~265Vac, continuous

operation.

Output voltage up to 600V, current up to 200A.

Features

Active power factor correction.

Parallel master/slave operation with active

current sharing.

Remote sensing to compensate for voltage drop

in load leads.

19" rack mounted ATE applications.

A built-in Web server.

OVP, OCP and OHP protection.

Preset memory function.

Adjustable voltage and current slew rates.

Bleeder circuit ON/OFF setting.

CV, CC priority start function. (prevents

overshoot with output ON)

Supports test scripts.

Interface

Built-in RS-232/485, LAN and USB interface.

Analog output programming and monitoring.

Optional interfaces: GPIB, Isolated Voltage (0-

5V/0-10V) and Isolated Current (4-20mA)

programming and monitoring interface.

(Factory options)

All manuals and user guides at all-guides.com

Otros manuales para PSU Series

Tabla de contenidos

Otros manuales de Fuente de alimentación de GW Instek

GW Instek

GW Instek PPH-1503D Manual de usuario

GW Instek

GW Instek PSW 30-36 Manual de usuario

GW Instek

GW Instek PEL-3000AH Series Manual de usuario

GW Instek

GW Instek PSW Series Manual de usuario

GW Instek

GW Instek Tequipment PEL-3000 Manual del propietario

GW Instek

GW Instek GPS-2303 Manual de usuario

GW Instek

GW Instek GRA-441 Manual de usuario

GW Instek

GW Instek PEL-3000A Series Manual de usuario

GW Instek

GW Instek PSW Series Manual del propietario

GW Instek

GW Instek SPD-3606 Manual de usuario

GW Instek

GW Instek PSH series Manual de usuario

GW Instek

GW Instek SPS-1230 Manual de usuario

GW Instek

GW Instek ASD Series Manual de usuario

GW Instek

GW Instek PSW Series Manual de usuario

GW Instek

GW Instek PSU Series Manual de usuario

GW Instek

GW Instek PEL-3000 Series Manual de usuario

GW Instek

GW Instek PSB-1400M Manual de usuario

GW Instek

GW Instek APS-9301 Manual de usuario

GW Instek

GW Instek PSB-2000 series Manual de usuario

GW Instek

GW Instek GPE-1326 Series Manual de usuario

GW Instek

GW Instek PSU Series Manual de usuario

GW Instek

GW Instek PLR Series Manual de usuario

GW Instek

GW Instek GCP-206P Manual de usuario

GW Instek

GW Instek PSS-3203 Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario