Grundig RS-Set 2 Manual de usuario

WIRELESS LOUDSPEAKERS

RS-Set 2

______________________________________________________________________________________________________

DEUTSCH

ENGLISH

FRANÇAIS

ITALIANO

PORTUGUÊS

ESPAÑOL

NEDERLANDS

DANSK

SVENSKA

SUOMI

3 Aufstellen und Sicherheit 10 Informationen

6 Auf einen Blick 94 Service

8 Anschließen und Betrieb

12 Set-up and safety 19 Information

15 Overview 94 Service

17 Connection and operation

22 Installation et sécurité 29 Informations

25 Vue d’ensemble 94 Service

27 Raccordement/fonctionnement

31 Installazione e sicurezza 38 Informazioni

34 In breve 94 Service

36 Collegamento e funzionamento

40 Instalação e segurança 47 Informações

43 Vista geral 94 Service

45 Ligação e funcionamento

49 Instalación y seguridad 56 Información

52 Vista general 94 Service

54 Conexión y funcionamiento

58 Installatie en veiligheid 65 Informatie

61 In een oogopslag 94 Service

63 Aansluiten en gebruik

67 Opstilling og sikkerhed 74 Informationer

70 Kort oversigt 94 Service

72 Tilslutning og brug

76 Uppställning och säkerhet 83 Information

79 En överblick 94 Service

81 Ansluta och använda

85 Sijoittaminen ja turvallisuus 92 Tietoja

88 Yleiskatsaus 94 Service

90 Liittäminen ja käyttö

SET-UP AND SAFETY ______________________________________________

To ensure that these high-quality, easy-to-use loudspeakers provide you with

lasting enjoyment, please observe the following instructions when setting them

up.

These loudspeakers are designed for the playback of wireless audio signals.

Any other use is expressly prohibited.

If the loudspeakers are subjected to sudden changes in temperature, for exam-

ple if they are brought in from the cold to a warm room, let them stand for at

least two hours. Do not connect them to the mains supply during this time.

The loudspeakers are designed for use in dry rooms. You must make sure that

the device is protected from moisture such as rain or splashing water.

When deciding where to place the device, please note that furniture surfaces

are covered by various types of varnish and plastic, most of which contain che-

mical additives. These additives can corrode the device supports, resulting in

residues on the furniture surfaces which are difficult or impossible to remove.

Do not place the loudspeakers close to heating units or in direct sunlight, as this

will impair the internal cooling.

Do not place any vessels containing fluids such as vases on the loudspeakers.

Should they be knocked over, fluid may spill on the electrical components, thus

presenting a safety risk.

Do not open the loudspeaker casing under any circumstances. The manufacturer

will not accept any liability for damage resulting from improper handling.

Thunderstorms are a danger to all electrical devices. Even if the loudspeakers

are switched off, they can be damaged by a lightning strike to the mains.

Always remove the mains plug in the event of an electrical storm.

Clean the gauze of the loudspeakers with a vacuum cleaner from time to time

(at low vacuum power without exerting any pressure).

°C

MAINS

230V

50/60Hz

RESET

! SERVICE !! SERVICE !! SERVICE !

MAINS

230V

50/60Hz

RESET

ENGLISH

SET-UP AND SAFETY_________________________________________________________________

The wireless transmission system

Your loudspeakers are equipped with an HF system which enables them to trans-

mit and receive audio and data signals. Cables, with the exception of the mains

cable are no longer necessary.

The HF transmission strength is limited by national and international regulations

to prevent radio interference from neighbouring devices.

The HF transmission power of the whole system is < 10 mW. This guarantees an

unhindered reception range of approximately 100 m. This range is restricted

inside buildings, depending on the construction materials used.

Avoid placing the system near metal objects such as radiators or electrical devi-

ces such as cordless telephones which use radio signals.

Since the audio and data signals are not transmitted on an exclusive range we

cannot guarantee that this will not cause interference. To avoid interference you

can change the communication channel for the audio transmitter (WT2).

In some circumstances, people, walls and other surfaces can reflect radio sig-

nals. Reflected signals can mix with direct (non-reflected) signals thus causing a

type of interference known as multi-path reception. This can lead to noise or a

temporary loss of sound. If such interference does occur, simply move the louds-

peakers or change transmission channels.

System components

Your RS-Set 2 loudspeakers are only suitable for use with the WT2 wireless

transmitter (in conjunction with the GRUNDIG Lenaro television).

SET-UP AND SAFETY_________________________________________________________________

MAINS

230V

0/60Hz

Positioning the active loudspeakers

There are two options for the RS-Set 2: wall-mounting or placing them on the

floor, on furniture or shelves.

1Place the active loudspeakers in the room around the television;

– or

hang the loudspeaker by the recess on the back of the speakers on a screw

which has been firmly anchored in the wall.

Note:

We recommend using the RS-Set 2 active loudspeaker as the rear loudspea-

ker. The LSP2 active loudspeakers can then be used as the front loudspea-

kers.

The rear loudspeakers should be placed at a sufficient distance and a suitable

height to the left and right or behind the listener. When setting up the active

loudspeakers, note that the minimum distance to the television is 50 cm.

When setting up the active loudspeakers, make sure that they stand securely

and are not affected by vibrations caused by resonance at high volumes.

Three feet are attached to the bottom of each active loudspeaker to increase

stability. If you hang the active loudspeakers to the wall you can remove the

feet from the bottom.

ENGLISH

OVERVIEW ________________________________________

The controls and connections for the RS-Set 2

ZPower switch, on the top of the device: switches the

device on and off again.

The loudspeaker is only fully disconnected from the

mains after the plug has been pulled out.

IAntenna.

Indicator In the mains button:

Flashing orange: installation phase 1 (sending iden-

tification);

Flashing green: installation phase 2 (identification

acknowledged);

Continuous orange: the loudspeaker is in stand-by

mode;

Continuous green: the loudspeaker is in operation;

Flashing green and red: reset mode – the loudspea-

kers have not been installed. This display changes to

flashing orange after a few seconds (see Installation

Phase 1).

Flashing red: the protective circuit has been actua-

ted.

Note:

If the protection circuit is actuated, switch off the

loudspeaker using the »Z« button and let it cool

down for at least 15 minutes.

OVERVIEW______________________________________________

RESET Back of device: press briefly to start installation with

WT2 manually; hold down (more than 10 seconds)

to delete the stored installation settings (initial state).

230 V Back of device: connection socket for mains

50/60 Hz cable.

Back of device: Flash plug cover. Only for dealers

for updating the device software.

RESET

MAINS

230V

50/60Hz

RESET

ENGLISH

Connection and installation

Connecting the mains cable

1Plug the mains cable into the »230 V 50/60 Hz« socket on the back of

the device.

2Insert the power cord plug in the socket.

3For instructions on how to install the loudspeakers with a WT2 transmitter

please refer to the appropriate operating manual.

Switching on and operating after installation

1Switch on both loudspeakers with »Z«.

– The orange indicators on the loudspeakers light up (stand-by).

2Switch on the television.

– The green indicators on the loudspeakers light up (operation).

Note:

The loudspeakers switch on or to stand-by mode automatically depending

on control signals from the WT2.

The change to stand-by function depends on the audio source and can take

up to 30 minutes.

CONNECTION AND OPERATION _____________

MAINS

230V

50/60Hz

CONNECTION AND OPERATION___________________________________________

Installing additional loudspeakers

For installation when expanding the system (for example from two to four

active loudspeakers), see the operating and installation instructions for WT2.

Resetting the loudspeakers to the original state

Note for dealers:

With this function you can delete all existing installation data and reset the

active loudspeakers to their original state.

1When switched on, press » RESET« on the bottom of the device for longer

than 10 seconds, using an implement such as a thin pencil.

– The display flashes green and red.

Note:

After the installation data has been deleted, the loudspeakers must be instal-

led again.

Reset mode is not required during operation and installation, and is there-

fore only available for specialist dealers.

RESET

ENGLISH

INFORMATION_____________________________________________________________

These loudspeakers are noise-suppressed according to the applicable EC directives.

This product fulfils the European directives 89/336/EEC, 73/23/EEC and 93/68/EEC.

This device conforms to the safety regulation DIN EN 60065 (VDE 0860) and therefore the interna-

tional safety regulation IEC 60065.

The type plate with information on the mains supply voltage and radio certification is located on the

back of the device.

The loudspeakers are intended for sale within the EU in the following countries: Belgium, Denmark,

Germany, UK, Finland, France, Ireland, Luxembourg, Netherlands, Norway, Austria, Portugal,

Sweden.

System

2-way bass reflex

Operating voltage: 230 V~ ± 10%

Mains frequency: 50/60 Hz

Max. power consumption: 210 W

Power consumption in Stand-by: < 3 W

Dimensions:

W x H x L 220 x 375 x 120 mm

Weight: 6,1 kg

Amplifier unit

Output: 75 W sine

120 W music

Receiver unit

Reception range – audio signal:

863...865 MHz

Reception range – data signal:

869.7…870 MHz

Transmission range: 50 ... 25,000 Hz

Technical data - RS-Set 2

DFM 869

Technical and optical modifications reserved.

Tabla de contenidos

Otros manuales de Oradores de Grundig

Grundig

Grundig GSB 600 NFC Manual de usuario

Grundig

Grundig BLUEBEAT GSB 500 Manual de usuario

Grundig

Grundig Sonoclock 360 Manual de usuario

Grundig

Grundig GSB 120 Manual de usuario

Grundig

Grundig GSB 750 Manual de usuario

Grundig

Grundig PartyHit Manual de usuario

Grundig

Grundig DPS 5200 Manual de usuario

Grundig

Grundig GSB 2000 Manual de usuario

Grundig

Grundig BLUEBEAT GSD 300 Manual de usuario

Grundig

Grundig Band 360 Manual de usuario

Grundig

Grundig SOLO-GBT Manual de usuario

Grundig

Grundig Bluebeat GSB 110 Manual de usuario

Grundig

Grundig FineArts MR 8000 Manual de usuario

Grundig

Grundig CLUB Manual de usuario

Grundig

Grundig GSB 200 NFC Manual de usuario

Grundig

Grundig GSB 800 Manual de usuario

Grundig

Grundig Audiorama 9000 Manual de usuario

Grundig

Grundig GSB 720 Manual de usuario

Grundig

Grundig Sonoclock 360 Manual de usuario

Grundig

Grundig GSB 810 Manual de usuario

Grundig

Grundig Sonoclock 360 Manual de usuario

Grundig

Grundig PSW 5000 Manual de usuario

Grundig

Grundig GSB 710 Manual de usuario

Grundig

Grundig PSW 5000 Manual de usuario

Manuales populares de Oradores de otras marcas

argon audio

argon audio IE20 Manual de usuario

Denon

Denon SC-N7 Manual de usuario

Gemline

Gemline Ace 3952 Manual de usuario

Focal

Focal ON WALL 300 Manual de instrucciones

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manual de usuario

SoundLogic

SoundLogic BCCS-6/6395 Manual de usuario

Peavey

Peavey DTH 218 Manual de usuario

Avantree

Avantree Pluto Air Manual de usuario

Morel

Morel Integra Series INTEGRA OVATION 4 Manual de usuario

Oppo

Oppo SONICA Manual de usuario

Bose

Bose SoundLink Wireless Music System Manual de usuario

Rocksteady

Rocksteady Stadium Manual de usuario

Bowers & Wilkins

Bowers & Wilkins 4 Manual de usuario

Sonance

Sonance SONOS OUTDOOR Series Manual de usuario

Electro-Voice

Electro-Voice EVID FM4.2 Manual de usuario

Pioneer

Pioneer XW-HTD630 Manual de usuario

Onn

Onn BWA16AA002 Manual de usuario

HP GL313AA - USB Speakers PC Multimedia Manual de usuario