Grundfos CRK Series Manual de usuario

CRK, MTR

Installation and operating instructions

GRUNDFOS INSTRUCTIONS

Table of contents

CRK, MTR

English (GB)

Installation and operating instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Čeština (CZ)

Montážní a provozní návod. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Deutsch (DE)

Montage- und Betriebsanleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Español (ES)

Instrucciones de instalación y funcionamiento . . . . . . . . . . . . . . . . . . . . . . . . . 40

Français (FR)

Notice d'installation et de fonctionnement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Italiano (IT)

Istruzioni di installazione e funzionamento . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Polski (PL)

Instrukcja montażu i eksploatacji . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Русский (RU)

Паспорт, Руководство по монтажу иэксплуатации . . . . . . . . . . . . . . . . . . . 88

Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

English (GB)

English (GB) Installation and operating instructions

Original installation and operating instructions

CONTENTS

Page

1. Symbols used in this document

2. Handling

When the entire pump is to be lifted, observe the

following:

• CRK and MTR pumps fitted with a Grundfos MG

motor up to 0.75 kW should be lifted in the pump

head by means of straps or the like.

• CRK and MTR pumps fitted with a Grundfos MG

motor from 1.1 to 22 kW must be lifted by means

of the lifting eyes.

• For other motor makes than those mentioned

above, we recommend to lift the pump in the

pump head by means of straps.

1. Symbols used in this document 4

2. Handling 4

3. Applications 5

3.1 Pumped liquids 5

4. Identification 5

4.1 Nameplate for CRK and MTR 5

4.2 Type key for CRK 6

4.3 Type key for MTR, MTRE 7

5. Technical data 8

5.1 Ambient temperature 8

5.2 Maximum permissible operating pressure

and liquid temperature for the shaft seal 8

5.3 Minimum flow rate 9

5.4 Electrical data 9

5.5 Maximum number of starts 9

6. Installation 9

6.1 Pump location 9

6.2 Suction conditions 10

7. Electrical connection 11

7.1 Frequency converter operation 11

7.2 Other motor makes 11

8. Start-up 12

8.1 Before starting the pump 12

8.2 Starting the pump 12

9. Maintenance 12

9.1 Filters 13

9.2 Periodic checks 13

10. Service 13

10.1 Service kits 13

10.2 Coupling adjustment 13

11. Sound pressure level 13

12. Fault finding 14

13. Disposal 15

Warning

Prior to installation, read these installation

and operating instructions. Installation and

operation must comply with local

regulations and accepted codes of good

practice.

Warning

If these safety instructions are not

observed, it may result in personal injury.

Warning

If these instructions are not observed, it

may lead to electric shock with consequent

risk of serious personal injury or death.

Warning

The surface of the product may be so hot

that it may cause burns or personal injury.

Caution

If these safety instructions are not

observed, it may result in malfunction or

damage to the equipment.

Note

Notes or instructions that make the job

easier and ensure safe operation.

English (GB)

3. Applications

The Grundfos pumps, types CRK and MTR, are tank

mounted multistage centrifugal pumps designed for

the following applications:

• liquid transfer in machine tools

• condensate transfer

• liquid transfer in industrial washing machines

• pressure boosting of cold or hot clean liquids

• similar applications.

3.1 Pumped liquids

Thin, non-explosive liquids, not containing fibres.

The liquid must not attack the pump materials

chemically.

When pumping liquids with a density and/or viscosity

higher than that of water, use motors with

correspondingly higher outputs, if required.

MTR version A pumps have a cast iron pump head.

In MTR version I and CRK version I pumps all parts

in contact with the pumped liquid are of stainless

steel EN/DIN 1.4301 or better.

4. Identification

4.1 Nameplate for CRK and MTR

Fig. 1 Example of nameplate

Warning

Do not use the pump for flammable liquids,

such as diesel oil and petrol.

TM05 5279 3912

Pos. Description

1 Type designation

2 Model

3 Product number

4 Place of production

5 Production year and week (YYWW)

6 P2, 50 Hz

7 Head against closed valve

8 Head at rated flow rate

Direction of rotation

CCW: Counter-clockwise

CW: Clockwise

10 Country of production

11 Approval marks

12 Frequency

13 Speed

14 Rated flow rate

15 Maximum pressure and temperature

The number of the copy of the technical

file kept at KEMA (stated if the pump is

ATEX classified)

17 The serial number of the pump (stated if

the pump is ATEX classified)

18 ATEX category (stated if the pump is

ATEX classified)

19 Minimum efficiency index

20 Hydraulic pump efficiency

Type MTR10-6/3 A-W-A-HUUV

Model A 96889995 P1 1019

f 50 Hz 1.1P2 kW

30.3 mmin H

max

2853n

Q10 m /h H 22.7 m

CCWbar/ C25/90

Made in Hungary

max

Serial No. 0001

MEI 0.70 p

-1

DK-8850 Bjerringbro, Denmark

--.-

12 3 4 5

19 20

English (GB)

4.2 Type key for CRK

*) See fig. 2.

Fig. 2 Number of chambers / impellers

Example CRK E 4 - 160 / 2 -x -x -x -xxxx

Pump type

Pump with integrated

frequency control

Rated flow rate [m3/h]

Number of chambers*) x 10

Number of impellers*)

Code for pump version

Code for pipework connection

Code for materials

Code for shaft seal and rubber pump parts

TM01 4991 1299

Number of

impellers

Number of

chambers

English (GB)

4.3 Type key for MTR, MTRE

Example MTR E 32 (s) -2 /1 -1 -A -F -A -H UU V

Pump type

Pump with integrated frequency control

Rated flow rate [m3/h]

All impellers with reduced diameter (applies only to MTR 1s)

Number of chambers, see fig. 2

Number of impellers, see fig. 2

Number of impellers with reduced diameter

Pump version

ABasicversion

B Oversize motor

C Suction pipe

E Pump with certificate/approval

F 120 °C version

H Horizontal version

J Pump with different max. speed

P Undersize motor

T Double oversize

X Special version

Pipe connection

F DIN flange

G ANSI flange

J JIS flange

M Square flange with internal thread

W Internal thread

WB NPT internal thread

X Special version

Materials

ABasicversion

I Wetted parts EN/DIN 1.4301 / AISI 304

X Special version

Shaft seal

H Balanced cartridge seal

Q Silicon carbide

U Tungsten carbide

B Carbon

E EPDM

FFXM

KFFKM

VFKM

English (GB)

5. Technical data

* Applies to pump version F

5.1 Ambient temperature

If the ambient temperature exceeds the above

temperature values or the pump is installed at an

altitude exceeding the above altitude values, the

motor must not be fully loaded due to the risk of

overheating. Overheating may result from excessive

ambient temperatures or the low density and

consequently low cooling effect of the air.

In such cases, it may be necessary to use a motor

with a higher rated output.

Fig. 3 Relationship between motor output (P2)

and ambient temperature/altitude

Example: A pump with a 1.1 kW IE2 MG motor: If

this pump is installed 4750 m above sea level, the

motor must not be loaded more than 88 % of rated

output. At an ambient temperature of 75 °C, the

motor must not be loaded more that 78 % of rated

output. If the pump is installed 4750 m above sea

level at an ambient temperature of 75 °C, the motor

must not be loaded more than 88 % x 78 % = 68.6 %

of rated output.

5.2 Maximum permissible operating

pressure and liquid temperature for the

shaft seal

Fig. 4 MTR 1s to 64

Pump type CRK MTR

Minimum liquid temperature [°C] -10 -10

Maximum liquid temperature [°C] +90 +90

(120*)

Maximum operating pressure [bar] 25 25

Enclosure class IP55 IP55

Motor power

[kW]

Motor make

Motor efficiency class

Max. ambient

temperature at full load

[°C]

Max. altitude above sea level

[m]

Pos. in output curve in fig. 3

0.06 - 0.18 Siemens - +40 1000 1

0.25 - 0.55 MG - +40 1000 1

0.75 MG IE2 +60 3500 2

1.1 - 22 MG IE2 +60 3500 2

30-45 Siemens IE2 +55 2750 3

TM04 4914 2209

TM02 7854 4303

20 25 30 35 40 45 50 55 60 65 70 75 80

100

[%]

t[°C]

1000 2250 3500 4750 m

-20 -10 0 10 20 30 40 50 60 70 80 90 100 110

p [bar]

HUUE / HUUV

t [°C]

English (GB)

5.3 Minimum flow rate

Due to the risk of overheating, the pump should not

be used at flows below the minimum flow rate.

The curve below shows the minimum flow rate as a

percentage of the nominal flow rate in relation to the

liquid temperature.

Fig. 5 Minimum flow rate in relation to

temperature

Note: The pump must never operate against a

closed discharge valve.

5.4 Electrical data

See motor nameplate.

5.5 Maximum number of starts

6. Installation

6.1 Pump location

The pump is designed for tank mounting in vertical

and horizontal position. However, only MTR version

H and MTRE version H are suitable for horizontal

mounting.

The pump is positioned in a hole cut into the tank

and is secured to the tank by four hexagon head

screws through the holes in the mounting flange.

Fig. 6 Vertical and horizontal installation

On horizontally installed MTR, MTRE pumps with

motors from 5.5 kW and up the motors have feet and

must be supported.

Fig. 7 Horizontally installed MTR with foot

TM04 5693 3809

Motor size

[kW]

Recommended maximum

number of starts per hour

0.06 - 0.18 100

0.25 - 2.2 250

3-4 100

5.5 - 11 50

15-22 40

30-45 8

40 50 60 70 80 90 100 110 120

t [°C]

Qmin

[%]

Warning

The pump must be installed so that

persons cannot accidentally come into

contact with the hot surface of the motor.

TM01 4990 1399TM04 5755 3809

Caution

For horizontally mounted pumps ensure a

sufficient sealing between pump flange

and tank. A sealing gasket will usually

suffice.

Caution

Before changing shaft seals for

horizontally mounted pumps, drain the

tank.

Caution

MTR 32, 45 and 64 pumps can only be

installed in vertical position.

Vertical Horizontal

English (GB)

Fig. 8 Vertical installation

Mounting flange dimensions:

6.2 Suction conditions

The bottom of the pump strainer must be at least 25

mm above the bottom of the tank.

The pumps are designed to provide full performance

down to a level of A mm above the bottom of the

strainer.

At a liquid level between A and B mm above the

bottom of the strainer, the built-in priming screw will

protect the pump against dry running.

Note: MTR 32, 45 and 64 pumps have no priming

screw.

Fig. 9 CRK 2, 4 and MTR 1s, 1, 3, 5

Fig. 10 MTR 10, 15, 20

Fig. 11 MTR 32, 45, 64

TM02 8042 4503

Pump type D1 D2 D3 L C X

CRK 2, 4 140 160 180 100 Rp 1 1/4

G 1 1/4 ∅7.5

MTR 1s, 1,

3, 5 140 160 180 100 Rp 1 1/4

G 1 1/4 ∅9.5

MTR 10,

15, 20 200 225 250 125 Rp 2

G 2 ∅9

MTR 32 190 220 250 150 DN 65 ∅12

MTR 45,

64 240 265 290 165 DN 80 ∅12

Pump type A [mm] B [mm]

CRK 2, 4 and MTR 1s, 1, 3, 5 41 28

MTR 10, 15, 20 50 25

MTR 32, 45, 64 70 -

4 x X

TM05 7223 0813TM05 7224 0813TM05 7225 0813

25 mm

Otros manuales para CRK Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Bomba de agua de Grundfos

Grundfos

Grundfos CR Series Manual de usuario

Grundfos

Grundfos TPE 1000 Series Manual de usuario

Grundfos

Grundfos DME series Manual de usuario

Grundfos

Grundfos MQ 3-25 Manual de usuario

Grundfos

Grundfos CRN-SF Series Manual de usuario

Grundfos

Grundfos CR Series Manual de usuario

Grundfos

Grundfos Sololift+ C-3 Manual de usuario

Grundfos

Grundfos SMART Digital XL DDA Manual de usuario

Grundfos

Grundfos MAGNA3 Series Manual de usuario

Grundfos

Grundfos SL1 Series Manual de usuario

Grundfos

Grundfos Hydro Multi-S Manual de usuario

Grundfos

Grundfos CR 95 Manual de instalación y operación

Grundfos

Grundfos TPE 1000 Series Manual de usuario

Grundfos

Grundfos Unilift KP 150 Manual de usuario

Grundfos

Grundfos UPS 15 Manual de usuario

Grundfos

Grundfos PS.G Series Manual de usuario

Grundfos

Grundfos AEF Manual de usuario

Grundfos

Grundfos Sololift2 C-3 Manual de usuario

Grundfos

Grundfos LC Manual de usuario

Grundfos

Grundfos DMX Series Manual de usuario

Grundfos

Grundfos MAGNA1 D Manual de usuario

Grundfos

Grundfos NB Manual de usuario

Grundfos

Grundfos Multilift MOG Manual de usuario

Grundfos

Grundfos BMQE 15 Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario