GrowSpan 115020 Manual de usuario
1
Revision date: 01.28.20
©2020 GrowSpan™
All Rights Reserved. Reproduction
is prohibited without permission. STK#
115020 (Twin-Wall Polycarbonate)
GrowSpan™
Single Swinging Door – Black-Out Door Kit
ATTENTION: Door kit includes materials for door only. All other components shown in the diagram above
and diagrams throughout this guide are not included and require additional purchase. Actual building may
differ from examples shown throughout this guide.
Ground Level
2Revision date: 01.28.20
READ THIS DOCUMENT BEFORE YOU BEGIN
Thank you for purchasing this GrowSpan™ door kit.
When properly assembled and maintained, this product
will provide years of reliable service. These instructions
include helpful hints and important information needed to
safely assemble and properly maintain the door. Please
read these instructions before you begin.
SAFETY PRECAUTIONS
• Wear eye protection.
• Wear head protection.
• Use a portable GFCI (Ground Fault Circuit
Interrupter) when working with power tools and cords.
WARNING: Individuals assembling this door are
responsible for designing and furnishing all temporary
bracing, shoring, and supports during assembly.
For safety reasons, those who are not familiar with
recognized construction methods and techniques
must seek the help of a qualified contractor.
REQUIRED TOOLS
This list identifies the main tools needed. Additional tools
and supports may be required depending on structure,
location, and application.
• Tape measure or measuring device
• Fine point marker to mark frame members
• Variable speed drill and impact driver (cordless with
extra batteries works best)
• Tool to cut polycarbonate panel
• Hammers, gloves, and eye protection
• Ladders, work platforms, and other machinery for
lifting designed to work safely at door and door frame
height.
ATTENTION: Consult the services of a qualified,
professional contractor if you are not familiar with
construction of similar frame structures and components.
Important Information
UNPACK AND IDENTIFY PARTS
Complete these steps to ensure that you have all
necessary parts:
1. Unpack shipment and place where you can easily
inventory parts. Refer to the Bill of Materials/Spec
Sheets.
2. Verify that all parts listed on Bill of Materials/Spec
Sheets are present. If anything is missing or you
have questions, consult parts guide and all diagrams
for clarification, or contact customer service.
NOTE: At this time, do not open plastic bags
containing smaller parts such as fasteners and
clamps (if equipped).
QUICK START DIAGRAMS
For a quick overview of door and door components,
consult the diagrams near the back of this guide.
ASSEMBLY PROCEDURE
Following instructions as presented will help ensure the
proper installation of end frame and door. These step
outline the assembly process:
1. Verify that all parts are included in the shipment.
Notify Customer Service for questions or concerns.
2. Read these instructions and all additional
documentation before you begin.
3. Gather the tools, bracing, and ladders (and lifts)
needed to install door and door frame.
4. Read the care and maintenance information on next
page.
3
Revision date: 01.28.20
Important Information
PARTS IDENTIFICATION
The following graphics and photos help identify hardware
for the door. (Some parts are not shown.)
Twin-Wall Black-Out Polycarbonate Door Kit
102921B & FA4484B
Tek Screws and neo-
bonded washers
104213
Aluminum
U-Channel Profile
108553
Wafer head screw
CARE AND MAINTENANCE
Proper care and maintenance of the door is important.
Check the following items periodically to properly maintain
door and door frame:
• Regularly check polycarbonate panel to ensure it
remains secure and is in good condition. Replace
damaged panel if needed.
• Check connections and all fasteners to verify that they
remain tight.
• Check contents of shelter to verify nothing is touching
polycarbonate panel that could cause damage or
interfere with door operation.
• Do not leave door partially opened. Close door and
secure with latch or prop open to avoid personal injury
or damage.
• For replacement or missing parts, contact your sales
representative.
SINGLE SWINGING DOOR KIT: READ THIS BEFORE
YOU BEGIN
Consult the services of a qualified contractor if needed. It
is the responsibility of the owner/contractor to adapt these
instructions to safely and competently install this door in
an end wall or building that it was not designed for.
Complete these steps:
1. Based on door dimensions, determine door position
in end frame. Use diagrams from both this guide and
end wall assembly guide (if availble).
2. Return to end wall instructions and frame end wall as
needed based on door location. Secure door framing
to end wall framing.
3. Assemble door and attach to door frame.
IMPORTANT NOTICE: Remove protective film from the
polycarbonate panel. Allowing film to remain intact and
in direct sunlight will make it difficult if not impossible
to remove. Store panel out of direct sunlight until film is
removed.
Rest panel edges on cardboard or other material to
protect it from dirt and damage during assembly.
Protective Film
Mark UV-protected side with a piece of tape after
protective film is removed and install that side
toward sun.
4Revision date: 01.28.20
ASSEMBLE DOOR FRAME COMPONENTS
Consult diagrams near the back of this guide before you begin.
ATTENTION: Photos and diagrams show attaching door frame to an end
wall constructed using girts with a specific profile. If actual end wall frame
differs, take necessary steps to alter instructions as needed to allow proper
installation of door jambs and header.
The following steps describe one way to set door jambs.
1. Using dimensions from Door Frame Layout located in Quick Start
section, locate and mark door jamb positions on site.
2. Dig a 10"-12" diameter hole at locations found in previous step to a
depth that is below geographic frost line. (Minimum depth: 24".)
3. Locate the 120" door jambs (105488120). Using a metal saw, cut and
remove 2-1/2" sections from one end of each door jamb as shown in
photo A. This creates a lip and allows jamb to be attached to girt (see
photo B and C and Side View diagram).
ATTENTION: Diagrams A-D show left door jamb only. Adjust cuts when
cutting end for right jamb.
4. Using diagrams as guides, attach jambs to girts using 108553 wafer
head screws (photo C, D, and E). Install end wall girts if needed.
ATTENTION: Position door jambs so open sides of C-channel face
away from door opening (as shown in photo C) and lip overlaps
girt. When attached to girt, lower end of each jamb extends into a
ground anchor hole and is secured in place using concrete. Consult
a knowledgeable contractor if needed. During installation, verify that
inside-to-inside dimension for door frame remains consistent.
Door Frame Assembly
Cut along
dotted lines.
Remove
this section
Vertical
Support
2-1/2" 2-1/2"
A
105488120
Door Jamb
End wall as seen
from the outside.
105488120
Door Jamb
Ground Level
C
D E
(inside-to-inside)
48-1/2"
48-1/2"
Install lower girts after
door frame (see X).
X
X
X
X
Wafer
Head
Screws
D
Left
Jamb
2-1/2" Lip
Left Jamb
B
Door Side
Front
E
Wafer Head
Screws
Front
Right Jamb
E
Girt
Side View
Jamb
Front
108553
Wafer Head
Screws Toward
Door
Opening
Front
C
5
Revision date: 01.28.20
ASSEMBLE DOOR FRAME COMPONENTS (continued)
Door Frame Assembly
Cut along
dotted lines.
Bend this
section inward
Door
Header
F
G
5. With door jambs attached, measure and mark height of rough
door opening. Consult drawing below and Door Frame Layout
located in Quick Start. Measure from finished grade to underside
of header.
6. Locate the 10548872 header material, measure outside-to-outside
width of door jambs, and cut header to required length.
7. Using a metal saw, cut two 2" sections and bend lip inward from
both ends of door header as shown at right (see photos F and G).
This creates two (2) tabs and allows header to attach to jambs.
Open channel of header points upward.
8. Position header so the two (2) tabs on each side overlap door
jambs (see photo H). Align header bottom with vertical support
marks made in Step 5. Ensure header is level and check
dimensions.
9. Attach front and back of header to jambs using wafer head
screws. Reinforce header by securing bent lip to vertical support
using Tek screws as shown in photo H. (Customer-supplied bolts
can also be used.)
10. After door frame is square and assembled, secure door jambs in
ground using concrete.
NOTE: Concrete should remain at least 2"- 4" below ground level
so it does not interfere with construction, installation of other end
wall components (if equipped), or door operation.
11. After assembling door frame, continue with door assembly.
H H
Concrete Ground Level
48-1/2"
92-1/2"
(inside-to-inside)
Door jamb
in concrete.
Ground
Level
*Not to
scale.
NOTE: Sample end frame and rafter
are not included with any door kit.
10548872
Header (cut to length)
(inside-to-inside)
Step 6
(outside-to-outside)
Wafer
Head
Screws
Tek screw
TOP VIEW
H
6Revision date: 01.28.20
Twin-Wall Single Swinging Door
SINGLE TWIN-WALL DOOR ASSEMBLY
Materials and parts needed to assemble the 115020 door
include:
• Door frame (102923), 8mm panel (113296Z096), door
hinges (FA5030), and latch (FA2410)
• Tek screws (FA4484B), neo-bonded washers
(102921B), and aluminum profile (104213)
Assemble and Attach Door
NOTE: Install polycarbonate panel with UV-protected side
toward the outside/sun. See panel film cover for details.
1. Locate door frame (102923), assemble (if needed),
and place on a flat surface.
2. Take panel and trim so length is one-quarter inch
(1/4") shorter than length of door frame.
3. Trim width of panel (if needed) so that it is one-quarter
inch (1/4") narrower than width of door frame.
NOTE: Trimming panels as instructed keeps panel
flush with door frame edge once aluminum profile
(104213) is installed.
4. Center panel on door frame.
5. Using Tek screws (FA4484B) and galvanized neo-
bonded washers, attach panel to horizontal cross tube
of door frame. Evenly space Tek screws and washers
every 12".
Photo shows panel attached to outside of door frame
and finished with aluminum (104213) U-channel.
7. To keep panel and profile in place, install Tek screws
and neo-bonded galvanized washers so screw
drills through longer edge of U-channel (underside
of panel) and washer overlaps shorter edge of
U-channel (top) as shown above. Evenly space Tek
screws every 12".
8. Locate door latch hole (5" from edge of door in cross
member) and drill 1" hole through panel at hole
location.
6. Install aluminum U-channel profile along all pannel
edges. Ends can be mitered or cut as shown.
NOTE: Attach panel in locations shown in photo to
hold panel in place while attaching aluminum profile
to panel.
To prevent interfering with latch installation, do not
install fasteners near latch mounting hole located in
frame cross tube.
Handle
9. Insert main handle of assembly through hole in door
and manuver handle and front plate into place as
shown above.
Hole in frame for door
latch. Set Step 8.
7
Revision date: 01.28.20
Twin-Wall Single Swinging Door
SINGLE TWIN-WALL DOOR ASSEMBLY (continued) 13. With assistance, set assembled door in door frame
and secure hinges to door jamb using one Tek screw
per hinge at this time.
Locations of door hinges may vary.
10. Mark plate mounting hole locations on panel and drill
a 5/16" hole through panel and door frame. Support
frame with a block of wood if needed.
11. Slide back mounting plate into position, align it with
mounting holes and front plate and secure using two
(2) ¼" x 3" bolts and lock nuts. Verify that latch turns
freely. Mount door latch guide (slotted plate) using the
remaining ¼" x 3" bolts. Position so latch handle is
level. See below.
Horizontal
Position
Door Latch
Guide
Latching
Plate
12. After assembling door, evenly space three (3) hinges
along door frame and attach using Tek screws.
14. Verify there is sufficient clearance along all door
edges to allow door to swing freely in the opening.
15. Test door operation, adjust hinges as needed, and
install remaining Tek screws.
16. Mount latching plate to door jamb using Tek screws.
Screws supplied with latch are not for metal jambs.
17. Attach weather stripping to inside door frame around
door to seal gaps.
12"
8Revision date: 01.28.20
QUICK START GUIDE
Single Swinging Door Kit
Quick Start Guide
Twin-Wall Door Sample
115020
Ground Level
ATTENTION: End frame and end rafter are not included with any
door kit. These are presented to demonstrate installation.
9
Revision date: 01.28.20
Door Frame Layout
48-1/2"
92-1/2"
inside-to-inside
measurements
105488120
Door Jamb
105488120
Door Jamb
Ground Level
10548872
Header
Wafer Head
Screws
Wafer Head
Screws
Wafer Head
Screws
Tek
Screws
Concrete
Tabla de contenidos
Otros manuales de Kit de invernadero de GrowSpan
GrowSpan
GrowSpan Gothic Pro Manual de usuario
GrowSpan
GrowSpan 108197H Manual de usuario
GrowSpan
GrowSpan PB01700R6 Manual de usuario
GrowSpan
GrowSpan 113463H Manual de usuario
GrowSpan
GrowSpan 103103 Manual de usuario
GrowSpan
GrowSpan 500 Series Manual de usuario
GrowSpan
GrowSpan Gothic Premium 108185H Manual de usuario
GrowSpan
GrowSpan 500 Series Manual de usuario
GrowSpan
GrowSpan 106363 Manual de usuario
GrowSpan
GrowSpan PB01670R4 Manual de usuario
GrowSpan
GrowSpan 500 Series Manual de usuario
GrowSpan
GrowSpan PGFLSAXXFCW0063 Manual de usuario
GrowSpan
GrowSpan 113170 Manual de usuario
GrowSpan
GrowSpan Round Premium Manual de usuario
GrowSpan
GrowSpan 2000 Series Manual de usuario
GrowSpan
GrowSpan 106205 Manual de usuario
GrowSpan
GrowSpan 117149 Manual de usuario
GrowSpan
GrowSpan Canopy-Top Cold Frame Series Manual de usuario
GrowSpan
GrowSpan 2000 Series Manual de usuario
GrowSpan
GrowSpan Gothic Premium 108190H Manual de usuario
Manuales populares de Kit de invernadero de otras marcas
ACD PRESTIGE
ACD PRESTIGE MR3 H Manual de usuario
Vitavia
Vitavia VA0040-TRP Manual de usuario
VegTrug
VegTrug Nursery Manual de usuario
Riverstone Networks
Riverstone Networks Monticello 041315V Manual de usuario
STC
STC Easy Grow 6x12 Greenhouse Manual de usuario
CLIMA POD
CLIMA POD Spirit V7 Series Manual de usuario
