Grower Select HS583 Manual de usuario
Hog Slat Inc. Newton Grove, NC USA September 2014
1
VentilationSystems
HS583 Curtain/Vent Machine Installation Manual
General Installation Notes:
Make sure that power is disconnected from system prior to servicing.
Installation of this equipment and related OEM equipment should be in accordance with these
instructions, OEM’s installation instructions and local codes (if applicable). Failure to follow specified
instructions may cause damage to equipment and/or personal injury or death.
Take special note of any Warnings or Safety Decals on the equipment and in manuals.
Always wear protective clothing and any applicable Personal Protective Equipment (Safety Glasses
and/or Ear Plugs) when working with the equipment.
Discarded materials, equipment and boxes should be recycled in accordance with local and national
codes.
Note: Actuator Assembly is to be wired in accordance with all applicable local and national electrical wiring codes. All
wiring sizes and fuse capacities are to be sized according to applicable electrical code specifications or other regulations.
SAFETY INSTRUCTIONS:
Read all safety messages in this manual and on equipment safety decals. Follow recommended
precautions and safe operating practices.
Ground all electrical equipment for safety.
Ground all non-current carrying metal parts to guard against electrical shock.
Always keep safety decals in good condition and replace missing or damaged decals.
Hog Slat Inc. Newton Grove, NC USA September 2014
2
VentilationSystems
COMPONENT LAYOUT (SERVICE REPLACEMENT PARTS)
Hog Slat Inc. Newton Grove, NC USA September 2014
3
VentilationSystems
ITEM #
PART #
QTY PER
DESCRIPTION
1
HS583-34
3
Pulley, Cast 3-1/2" with double ball bearings
2
HS583-42
1
Bearing Flange 1" I.D
3
HS583-8-2
1
Load Nut, nylon
4
HS583-9
2
Slide, load block
5
HS583-8
1
Load block assembly with load nut & cotter pins
6
1
1 ¼” External snap ring, supplied with HS583-8-2
7
HS583-41
2
Threaded collar, seal thrust bearing nylon
8
HS583-12
1
Thrust bearing, 1” ID, D9
9
HS583-11A24
1
ACME screw, 24” machine
HS583-11A36
1
ACME screw, 36” machine
HS583-11A48
1
ACME screw, 48” machine
10
HS613
1
Spider Gear-spacer Hytrel (white) L090/L095
11
LOV38146
1
Coupling Jaw L095 5/8" bore with keyway
12
HS9050
1
Motor 1/8 HP, 115V AC, 60 Hz, 1.9A FL, 28RPM
HS9051
1
Motor 1/8 HP 230V AC, 50/60Hz, 0.75/0.90A FL, 24/29 RPM
HS9052
1
Motor 1/8 HP, 115V AC, 60 Hz, 1.65A FL, 16RPM
13
HS583-31
1
Switch assembly with (6) EL1135 micro switches
14
EL1001
1
Switch, Toggle SPDT , 10A @ 250 Volt, CTR OFF
15
EL1005
1
Switch, Toggle DPDT , 10A @ 250 Volt, CTR OFF
16
HS612
1
Knob, tri-handle, ¼-20 insert
17
HS583-45
1
Handle, Front door
18
HSLABEL-084
1
Label, “Caution Automatic Equipment”
19
HSLABEL-083
2
Label, “Warning Moving Parts”
20
HSLABEL-087
1
Label, “Grease Location”
21
HS583-27-24
1
Limit rod, 24” machine
HS583-27-36
1
Limit rod, 36” machine
HS583-27-48
1
Limit rod, 48” machine
22
HS583-28
2
Collar, steel 3/8'' w/ set screw
23
HS583-29
2
Spring, limit rod
24
EL1083
2
Rubber cover, toggle switch
25
HSLABEL-008
1
Label, Warning-Shock Hazard
Hog Slat Inc. Newton Grove, NC USA September 2014
4
VentilationSystems
SAFETY DECALS AND WARNING LABELS
SPECIFICATIONS:
Maximum Load: Ratio : Machine travel : vent/ curtain travel
Example: 2:1 = 2” machine travel : 1” vent/curtain travel
Refer to Figures 6 and 7
RPM 2:1 pulley ratio 1:1 pulley ratio 1:2 pulley ratio
15 & 28
4,000 lbs
2,000 lbs
1,000 lbs
60
2,000 lbs
1,000 lbs
500 lbs
Located on front door of machine
Located on side of cabinet near
cable/chain exits.
Located at bottom of front door
near removal point.
Hog Slat Inc. Newton Grove, NC USA September 2014
5
VentilationSystems
UNPACKING UNIT
Remove front cabinet door.
Packaged inside cabinet chassis:
1. HS583-50 Hardware Kit
a. Front cabinet door hardware
i. HS583-45 Handle
ii. (2) 605013 Flange head bolts
iii. (2) 60577 Flange nuts
iv. HS612 Tri-handle knob
b. Machine mounting hardware
i. (1) 3/8” x 3” Lag bolt
ii. (6) 3/8” x 2” lag bolts
iii. (2) 61646 liquid tight connectors
2. Installation manual
Assembly of Cabinet door with hardware supplied.
HS612 Tri-Handle Knob installs over threaded stud when cabinet door is placed on machine.
Door slides under lip at
top of machine
Lift up from bottom
and slide door down
to remove.
Hog Slat Inc. Newton Grove, NC USA September 2014
6
VentilationSystems
INSTALLATION / OPERATION
1. The HS583 Curtain/Vent machine is equipped with a key hole slot for easy installation as well as
(6) locations to secure unit to a wall.
2. Install (1) 3/8” X 3” Lag bolt (supplied) in the wall of the building in the desired location leaving
bolt out approximately ¼”. Lag bolt location to be center line of the machine and installed 6 1/4”
below the height of the top of the machine. Allow a minimum of 1” clearance above machine
from any structure in order to provide adequate clearance for hanging machine on keyhole lag
bolt.
3. Hang machine on bolt aligning keyhole slot located near top of the machine. (Figure 1)
Figure 1
Keyhole
mounting
location
MODEL LENGTH
“A”
24”
30 3/8”
36”
42 3/8”
48”
54 3/8”
Hog Slat Inc. Newton Grove, NC USA September 2014
7
VentilationSystems
4. DO NOT OPERATE MACHINE while hanging on this bolt. Level machine and secure machine
using 3/8” x 2” Lag bolts (supplied) in the (6) mounting locations. (Figure 2)
Figure 2
5. When connecting cables, the load nut should be near the “Closed” position to allow enough
cable for manual winch connection.
(4) Inside
chassis
mounting
locations
(2) External
Mounting
Locations
Hog Slat Inc. Newton Grove, NC USA September 2014
8
VentilationSystems
6. Run cable ends through side of machine around pulley down to the load block. Route cables
around pulleys as shown in below figures that best suits the application.
7. Cables should exit 90 Degrees to cabinet side to ensure even load on both sides of load block.
Changing the exit angle will change force distribution on load block resulting in shorter load
nut life.
Figure 3
Figure 4
Figure 5
One machine used to pull two
curtains from both sides, loop
cable around pulleys.
(Figure 3)
One machine used to pull
curtain from LEFT side, loop
cable around pulleys.
(Figure 4)
One machine used to pull
curtain from RIGHT side, loop
cable around pulleys.
(Figure 5)
Hog Slat Inc. Newton Grove, NC USA September 2014
9
VentilationSystems
8. Install corner brackets, through wall brackets and hand winch. Use bearing supported pulleys on
any pulley that rotates during operation of machine. Figures below show examples of external
cabling and hand winch location.
Figure 7
Pulley arrangement for 1:1
ratio. For each 1 inch travel of
the machine there is 1 inch
travel of the curtain. (Figure 6)
Pulley arrangement for 1:2
ratio. For each 1 inch travel of
the machine there is 2 inch
travel of the curtain. (Figure 7)
Hog Slat Inc. Newton Grove, NC USA September 2014
10
VentilationSystems
Outside Endwall Mount – Curtains
1:2 Ratio
Figure 8
Figure 9
Tabla de contenidos
