Grizzly H6192 Manual de usuario

Product Information

• 10,000 RPM

• Requires 90 PSI

• Requires 5 CFM

• Requires 5" hook and loop sanding disc with

5-hole pattern

• 1/4" NPT air inlet

• Weighs 2.4 lbs.

• 11/4" Dust port

• Directional exhaust port

Inventory

A. Orbital Sander ..............................................1

B. Wrench .........................................................1

MODEL H6192

RANDOM ORBITAL SANDER

INSTRUCTION SHEET

EYE INJURY HAZARD!

Always wear safety glasses

when using this tool to

prevent serious personal

injury.

INJURY HAZARD!

Always disconnect tool from

air to prevent unexpected

operation during service.

DUST HAZARD!

Always wear respirator when

using this tool. Figure 1. Model H6192 inventory.

Assembly

To assemble the Model H6192:

1. Install a 1⁄4" NPT male quick-connect fitting

(not included) into the air inlet.

2. Attach a 5" hook and loop sanding disc to the

sanding pad as shown in Figure 2.

Figure 2. Attaching sanding disc.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BL8505 PRINTED IN TAIWAN

DO NOT EXCEED 120 PSI!

Personal injury could

occur.

Maintenance

Lubricate at the beginning of the sanding task.

Place one or two drops of pneumatic tool oil

directly into the air fitting as shown in Figure 5.

Figure 5. Lubricating directly into air fitting.

Operation

To operate the sander:

1. Plug the tool into compressed air and turn ON

the optional canister vacuum.

2. Hold the sander and press the throttle lever

(Figure 4) to turn the sander ON.

Considerable caution must be used with an inline

lubricator set up, as excess oil will be expelled

from the sander onto the workpiece. If you must

use an inline lubricator, monitor the exhaust port

for oil emissions to avoid spraying oil on your

workpiece.

Before installing the sanding disc, run the sander

for a few minutes to eject excess oil, then wipe

the tool down with a clean rag and begin sanding.

Oil the tool after use or storage.

Service

To replace the sanding pad:

1. Insert the included wrench onto the spindle

as shown in Figure 6.

3. Turn the regulator (Figure 4) to adjust the

sanding pad speed to a fixed rate, and rotate

the directional exhaust port.

4. Remove pressure on the throttle lever to stop

the sanding pad, then turn the vacuum OFF.

5. When the sandpaper loses its effectiveness,

disconnect the sander and replace the

sandpaper.

If you need help with your new pneumatic tool, call

our Tech Support at: (570) 546-9663.

Figure 4. Sander controls.

Figure 6. Wrench inserted onto spindle.

2. Hold the wrench and unscrew the sanding

pad.

3. Install a new sanding pad (Part # PH6192039)

and secure it with the wrench.

Wrench

Sanding

Pad

3. (Optional) Attach the sander to a 11/4" vacu-

um hose as shown in Figure 3.

Figure 3. Attaching sander to 11/4" canister

vacuum hose.

Regulator

Exhaust

Port

Throttle

Lever

Accessories

G9955—Bench Top Dual Fan Dust Filter

Two separately switched fan motors can be used

to draw a maximum 400 CFM of your dusty shop

air though the 5 micron pleated filter. Perfect for

sanding and power carving, the clear plastic hood

helps to direct flow from the work area directly into

the filter.

Figure 10. G9955 Dust Filter.

Figure 9. Half-mask respirator and disposable

cartridge filters.

H2499—Small Half-Mask Respirator

H3631—Medium Half-Mask Respirator

H3632—Large Half-Mask Respirator

H3635—Disposable Cartridge Filter Pair P100

Wood dust is now considered a known carcino-

gen and has been linked to nasal cancer and

severe respiratory illnesses. If you work around

dust everyday, a half-mask respirator can be a

lifesaver. Also compatible with safety glasses!

H3275—1⁄4" x 25' Coil Hose

These recoil hoses stay neatly coiled when not

in use, yet stretch to full length when needed.

Great for bench-top use when clutter is always a

concern. Coil springs protect ends from kinking.

1⁄4"NPT.

Figure 8. H3275 Coil Hose.

H3263—5 Pc. Quick Coupler Set

This 5-Pc. Solid Brass Quick Coupler Set includes

one 1⁄4" NPT female quick coupler, one 1⁄4" NPT

female thread connector and three 1⁄4" NPT male

thread connectors.

Figure 7. H3263 Quick Coupler Set.

G6407—60 Grit, 5" Sanding Disc

G6408—80 Grit, 5" Sanding Disc

G6409—100 Grit, 5" Sanding Disc

G6410—120 Grit, 5" Sanding Disc

G6411—150 Grit, 5" Sanding Disc

G6412—220 Grit, 5" Sanding Disc

H6604—280 Grit, 5" Sanding Disc

H6605—320 Grit, 5" Sanding Disc

H6606—400 Grit, 5" Sanding Disc

H6607—500 Grit, 5" Sanding Disc

H6608—600 Grit, 5" Sanding Disc

H6192 Parts Breakdown and List























































































































REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PH6192001 REGULATOR 23 PRP61M ROLL PIN 3 X 12

2 PH6192002 O-RING 24 PH6192024 CYLINDER

3 PR49M INT RETAINING RING 12MM 25 PH6192025 O-RING 47 X 2.5

4 PH6192004 O-RING 26 PH6192026 FRONT PLATE

5 PH6192005 VALVE STEM 27 P6000 BALL BEARING 6000ZZ

6 PH6192006 WASHER 28 PH6192028 SPECIAL WASHER

7 PH6192007 NEEDLE VALVE 29 PH6192029 SPECIAL WASHER

8 PH6192008 VALVE SPRING 30 PH6192030 WOODRUFF KEY

9 PH6192009 INLET BUSHING 31 PH6192031 MOTOR SHAFT BALANCER

10 PH6192010 MUFFLER BODY 32 PR48M EXT RETAINING RING 11MM

11 PH6192011 O-RING 33 P6001 BALL BEARING 6001ZZ

12 PH6192012 EXHAUST SLEEVE 34 PH6192034 SPECIAL EXT RETAINING RING

13 PH6192013 EXHAUST SLEEVE NUT 35 PH6192035 SHAFT

14 PH6192014 THROTTLE LEVER 36 PH6192036 HOUSING COVER

15 PRP53M ROLL PIN 3 X 40 37 PSB50M CAP SCREW M5-.8 X 10

16 PH6192016 HOUSING 39 PH6192039 5" SANDING PAD

17 PH6192017 GASKET 40 PH6192040 SPINDLE WRENCH

18 PR16M EXT RETAINING RING 9MM 44 PH6192044 VACUUM PORT 1-1/4 " OD

19 P6000 BALL BEARING 6000ZZ 45 PH6192045 SHROUD

20 PH6192020 REAR PLATE 46 PH6192046 DUST WARNING LABEL

21 PH6192021 ROTOR BLADE 47 PH6192047 GRIZZLY AIR TOOLS LABEL

22 PH6192022 ROTOR

Otros manuales de Lijadora de Grizzly

Grizzly

Grizzly G9984 Manual de usuario

Grizzly

Grizzly G1071 Manual de usuario

Grizzly

Grizzly G0518 Manual de usuario

Grizzly

Grizzly G0449 Manual de usuario

Grizzly

Grizzly G0458Z Manual de usuario

Grizzly

Grizzly G0936 Manual de usuario

Grizzly

Grizzly G0716 Manual de usuario

Grizzly

Grizzly G0644 Manual de usuario

Grizzly

Grizzly G0529 Manual de usuario

Grizzly

Grizzly H3120 Guía

Grizzly

Grizzly POLAR BEAR Series Manual de usuario

Grizzly

Grizzly G4185 Manual de usuario

Grizzly

Grizzly H3143 Guía

Grizzly

Grizzly T32004 Manual de usuario

Grizzly

Grizzly G0489 Manual de usuario

Grizzly

Grizzly G0474 Guía de inicio rápido

Grizzly

Grizzly G0563 Manual de instrucciones

Grizzly

Grizzly G0489 Guía de inicio rápido

Grizzly

Grizzly G0472 Manual de usuario

Grizzly

Grizzly G0538 Guía de inicio rápido

Grizzly

Grizzly H0584 Guía de inicio rápido

Grizzly

Grizzly G1066R Manual de usuario

Grizzly

Grizzly G0864 Manual de usuario

Grizzly

Grizzly G0563 Guía de inicio rápido

Manuales populares de Lijadora de otras marcas

Oliver

Oliver 6305 Manual de usuario

Jet

Jet 22-44 Pro-3 Manual de servicio

Makita

Makita M9204 Manual

Makita

Makita M9204 Manual de usuario

Craftsman

Craftsman 351.215131 Manual de usuario

Clarke

Clarke Woodworker CBS1-5B Manual de instrucciones

Chicago Pneumatic

Chicago Pneumatic CP9778 Manual de usuario

Nitto Kohki

Nitto Kohki BB-20 Manual de usuario

Ferm

Ferm FEOS-135 Manual de usuario

Unior

Unior 1510 Manual de usuario

stayer

stayer ls1200 Manual de usuario

Jet

Jet JSG-96 Manual de servicio

Parkside

Parkside PDS 290 B2 Manual de usuario

Status

Status XPA Series Manual de usuario

Clarke

Clarke EZ Sand Manual de usuario

Craftsman

Craftsman 113.22521 Manual de usuario

Craftsman

Craftsman 113.225831 Manual de usuario

CLAS

CLAS OP 1429 Manual de usuario