Grizzly H8093 Manual de usuario

Model H8093

21⁄2 Ton Low Profile

Garage Jack

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TR8824 PRINTED IN CHINA

Specifications

Maximum Lifting Capacity ................... 5000 Lbs.

Lifting Range ......................................33⁄8"–151⁄16"

Weight ................................................... 108 Lbs.

If you need help with the Model H8093, call our

Technical Support line at: (570) 546-9663.

Failure to follow these instructions could

result in serious personal injury or death:

1. DO NOT overload this jack beyond its

rated capacity. Overloading can cause

the jack to collapse and drop the load.

2. ALWAYS support the vehicle with appro-

priately rated support stands before

working under it.

3. DO NOT attempt to move the vehicle

while the jack is in use.

4. Use only on hard level surfaces like

concrete or asphalt. Other surfaces are

potentially unstable.

5. Center the load on the jack to maintain

proper balance and stability.

6. DO NOT use jack if it begins leaking

fluid or if it sinks when placed under

load. These are indications that the jack

needs to be immediately serviced.

Operation

To raise the jack, rotate the pump valve knob

clockwise completely, then move the pump han-

dle or foot pump up and down. To lower the jack,

slowly rotate the pump valve knob counterclock-

wise.

Figure 1. Jack controls.

Pump

Handle

Pump Valve

Knob

Foot

Pump

Maintenance

Keep the hydraulic rams clean and free of any

dust, dirt, or foreign debris. Abrasive material

stuck to the ram can damage the hydraulic seal

when the ram is retracted back into the jack.

Regularly wipe the hydraulic rams clean with a

lightly oiled rag.

The Model H8093 will require hydraulic fluid after

long-term use. This will be noticeable if the jack

will not reach its maximum height when pumped.

Only use a high quality hydraulic fluid.

To add hydraulic fluid:

1. Completely lower the jack.

2. Remove the top cover plate from the jack and

remove the fill plug shown in Figure 2.

Bleeding the Air

If the jack becomes spongy or will not rise when

pumped, then air bubbles may be in the hydraulic

system.

To remove the air bubbles:

1. Remove the fill plug.

2. Rotate the pump valve knob counterclock-

wise one full turn.

3. Pump the jack quickly ten times to purge the

air from the system.

4. Replace the fill plug and test the operation of

the jack.

—If the jack did not perform properly, then air

may need to be bled from the pump system

again.

3. Add fluid until it reaches the top of the fill plug

hole.

4. Replace the fill plug.

5. Test the operation of the jack by pumping

it up to the maximum height and applying a

load. The jack should hold the weight of the

load without a sinking or spongy feeling.

—If the jack did not perform properly, then

air may need to be bled from the pump

system.

Figure 2. Fill plug.

Fill Plug

H8093 Parts Breakdown and List

















































 







  











































REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PH8093001 COVER 27 PH8093027 SUPPORT ROD

2 PN09M HEX NUT M12-1.75 28 PH8093028 TORSION SPRING

3 PH8093003 FENDER WASHER 12MM 29 PH8093029 EXTENSION SPRING

4 PH8093004 FRONT WHEEL SLEEVE 30 PH8093030 PUMP ASSEMBLY

5 PH8093005 FRONT WHEEL 31 PH8093031 FOOT PEDAL

6 PH8093006 LEFT FRAME 32 PS14M PHLP HD SCR M6-1 X 12

7 PH8093007 RUBBER PAD 33 PH8093033 PEDAL BASE

8 PH8093008 SADDLE 34 PH8093034 IDLER WHEEL

9 PH8093009 LIFTING ARM ASSEMBLY 35 PH8093035 IDLER WHEEL SHAFT

10 PH8093010 FRONT WHEEL AXIS 36 PH8093036 TORSION SPRING

11 PH8093011 CONNECTING ROD AXIS 37 PH8093037 HANDLE SOCKET

12 PH8093012 LONG CONNECTING ROD 38 PB35M HEX BOLT M12-1.75 X 40

13 PR06M EXT RETAINING RING 16MM 39 PW06M FLAT WASHER 12MM

14 PH8093014 RIGHT FRAME 40 PH8093040 OPERATION HEAD

15 PH8093015 CONNECTING ROD 41 PH8093041 OPERATION ROD 2

16 PLW06M LOCK WASHER 10MM 42 PH8093042 COTTER PIN 4 X 26MM

17 PN02M HEX NUT M10-1.5 43 PH8093043 COTTER PIN 3 X 16MM

18 PS26M PHLP HD SCR M6-1 X 20 44 PH8093044 OPERATION ROD 1

19 PH8093019 AXIS FOR PUMP 45 PH8093045 COTTER PIN 3 X 28MM

20 PB20M HEX BOLT M8-1.25 X 35 46 PH8093046 PUMP VALVE KNOB

21 PR11M EXT RETAINING RING 25MM 47 PH8093047 LOWER HANDLE

22 PLW05M LOCK WASHER 12MM 48 PS03M PHLP HD SCR M6-1 X 8

23 PLW12M LOCK WASHER 18MM 49 PH8093049 UPPER HANDLE

24 PH8093024 CONNECTING BOLT 50 PH8093050 MACHINE ID LABEL

25 PH8093025 REAR CASTER ASSEMBLY 51 PH8093051 FILL PLUG

26 PS29M PHLP HD SCR M12-1.75 X 25

The machine ID label warns about hazards and ways to prevent injury. The owner of the jack

MUST maintain the original location and readability of the label. If the label is removed or becomes

unreadable, contact Grizzly at (800) 523-4777 or www.grizzly.com to order a new label.





















Tabla de contenidos

Otros manuales de Herramientas eléctricas de Grizzly

Grizzly

Grizzly G0633 Guía de inicio rápido

Grizzly

Grizzly G0490X Manual de usuario

Grizzly

Grizzly G4017 Manual de usuario

Grizzly

Grizzly G0801 Manual de usuario

Grizzly

Grizzly Extreme Series Manual de usuario

Grizzly

Grizzly H0778 Manual de usuario

Grizzly

Grizzly G0610 Manual de usuario

Grizzly

Grizzly Vertical Mill G0667X Manual de usuario

Grizzly

Grizzly G0543 Manual de usuario

Grizzly

Grizzly G1004 Manual de usuario

Grizzly

Grizzly G8689 Manual de usuario

Grizzly

Grizzly G9901 Manual de usuario

Grizzly

Grizzly T28048 Manual de usuario

Grizzly

Grizzly G0530 Manual de usuario

Grizzly

Grizzly T10828 Manual de usuario

Grizzly

Grizzly G0747 Manual de usuario

Grizzly

Grizzly AGS 720 Lion-Set Instrucciones de funcionamiento e instalación

Grizzly

Grizzly H8090 Manual de usuario

Grizzly

Grizzly H5503 Manual de usuario

Grizzly

Grizzly G1024 Manual de usuario

Grizzly

Grizzly G0734 Manual de usuario

Grizzly

Grizzly H2801 Manual de usuario

Grizzly

Grizzly G0473 Guía de inicio rápido

Grizzly

Grizzly H8231 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual