Griven AL2502 Manual de usuario
GoboLED 80 D
AL2502
Manuale di istruzioni
Instructions manual
I DEX
1.0 Introduction .................................................................................................................................20
1.1 Safety information.......................................................................................................................................................20
1.1.1 Protecting against electric shock ..........................................................................................................................20
1.1.2 Installation ................................................................................................................................................................20
1.1.3 Protection against burns and fire ...........................................................................................................................20
1.1.4 Weather protection..................................................................................................................................................20
1.1.5 Forced ventilation ....................................................................................................................................................20
1.2 Compliance ................................................................................................................................................................20
2.0 Size ...............................................................................................................................................21
3.0 Packaging and transport ...........................................................................................................21
3.1 Packaging ...................................................................................................................................................................21
3.2 Transport ......................................................................................................................................................................21
4.0 Installation ...................................................................................................................................22
4.1 Fixing ............................................................................................................................................................................22
4.2 Adjusting light beam direction..................................................................................................................................22
4.3 Connection to mains power ......................................................................................................................................23
4.4 Connection to DM signal .........................................................................................................................................24
4.5 Gobo installation.........................................................................................................................................................25
4.6 Focus and zoom..........................................................................................................................................................27
5.0 Use of the unit..............................................................................................................................28
5.1 Setting operating mode .............................................................................................................................................28
5.2 Setting DM address...................................................................................................................................................28
5.3 DM functions .............................................................................................................................................................29
5.3.1 DM functions in CH mode = 1...............................................................................................................................29
5.3.2 DM functions in CH mode = 2...............................................................................................................................30
5.3.3 DM functions in CH mode = 3...............................................................................................................................30
5.3.4 DM functions in CH mode = 4...............................................................................................................................30
6.0 Master-Slave and Automatic function......................................................................................31
6.1 MASTER configuration.................................................................................................................................................31
6.2 SLAVE configuration....................................................................................................................................................32
6.3 AUTOMATIC configuration .........................................................................................................................................32
7.0 Thermal protection .....................................................................................................................33
8.0 Maintenance...............................................................................................................................33
8.1 Cleaning the unit ........................................................................................................................................................33
8.1.1 Fixture body..............................................................................................................................................................33
8.1.2 Fans and air passages.............................................................................................................................................33
8.2 Regular checks ...........................................................................................................................................................33
9.0 Spare parts ..................................................................................................................................33
10.0 Troubleshooting.........................................................................................................................34
11.0 Disposal......................................................................................................................................35
12.0 Technical specifications ..........................................................................................................35
1.1 Safety information
1.1.1 Protecting against electric shock
• Disconnect the unit from mains supply before servicing it or performing any other action.
• Always ground/earth the unit electrically.
• Before connecting the unit to power supplies, verify that operating voltage and frequency are compatible.
• Do not handle the unit with wet hands or in the presence of water.
• Check regularly that the power supply cable is not damaged or crushed.
• Apply to a qualified technician for any regular maintenance action not described in this manual.
1.1.2 Installation
• Fix the unit with screws, hooks or any other support able to bear the weight of the unit itself.
• The unit installation actions must be performed by a qualified staff.
1.1.3 Protection against burns and fire
• Suitable to be installed onto normally inflammable surfaces.
• Damaged fuses are always to be replaced with working fuses as per type and rate specified.
• The unit is not to be installed in places where the ambient temperature exceeds 40° (104°F).
1.1.4 Weather protection
The unit is classified as device with an IP65 weather protection rate.
The cooling system is classified as device with an IP55 weather protection rate.
1.1.5 Forced ventilation
You will note several air vents on the body of the projector. To avoid any problems associated with overheating,
clean air vent periodically.
1.2 Compliance
• Product in compliance with EN60598-1 EN60598-2-17.
• Product in compliance with 2002/95/CE (RoHS).
1.0 Introduction
Warning!
This unit is suitable for professional use only, not for domestic use.
20 English
3.1 Packaging
Check carefully the content of the box and, in case of damage, contact your forwarder immediately. The fol-
lowing items are included in the box of this unit:
n° 1 Goboled 80 D unit
n° 1 owner’s manual
3.2 Transport
The carton box has not been designed to be used more than once, therefore, it is recommended to use one of
our flight cases to transport the unit.
2.0 Size
280.5mm
11"
216mm
8.5"
150.3mm
5.9"
150.3mm
5.9"
64.5mm
2.5"
164mm
6.5"
152mm
6"
273mm
10.8"
425.3mm
16.7"
Ø80mm
3.2”
Ø10.5mm
0.4”
3.0 Packaging and transport
Warning!
• Griven S.r.l. liability will cease upon consignment of goods to the forwarder: claims for damage due to trans-
port must be addressed directly to the forwarder.
• Griven S.r.l. will accept claims for broken or missing goods only within seven days of receipt of the goods.
• Returns of equipment will not be accepted without prior authorization granted by Griven S.r.l. and if not duly ac-
companied by relevant shipping documents.
English 21
22 English
4.1 Fixing
The unit can be used both rested on floor and fixed onto a structure. The unit can operate in any position.
Use the holes “4” Ø10.5 (0.4”) in the bracket to fix the unit.
4.2 Adjusting light beam direction
A. Untighten the lateral screw “5”.
B. Rotate the bodies of the unit towards desired direction and
tighten the screw “5”.
4.0 Installation
Ø80mm
3.2”
Ø10.5mm
0.4”
4
5
English 23
4.3 Connection to mains power
The unit can operate with voltage from 100 to 240Vac and with frequency of 50 and 60Hz.
It is not necessary to effect any setup procedures. The fixture will automatically adjust its operation to suit any fre-
quency or voltage within this range.
The unit is fitted with internal pins for the connection of the of the main cable, as shown in the following
pictures.
A. Untighten the screw “6” and remove the box cover.
B. Let the signal cables pass through the cable glands “7”
located onto the unit body and connect the main cables to
the pin “8”.
The connection of the cable to the unit must be performed re-
specting the label next to the terminal box.
Size and connection scheme of the main cable are shown in
the following picture.
Warning!
• Before connecting the unit, verify that power supplies features are compatible with the unit features.
• The unit must never be installed if not grounded electrically.
• It is suggested to use a magnetothermic switch along the power supply line, as prescribed by in force rules.
• The unit must not be powered up through a dimmer power device.
• Wiring and connection actions are to be performed by a qualified staff.
6
78
ø4.5 MIN
ø10 MAX
3x1.5mm²
minimum cable
section
Ground
Neutral
Phase
Main cable size
L
N
24 English
C. Close the unit again by tighten the screw “6” previously re-
moved.
4.4 Connection to DMX signal
The DMX signal is to be connected by using a shielded cable designed for devices RS-485.
The unit is fitted with internal pins for the connection of the of the DMX signal cable, as shown in the following
pictures.
A. Untighten the screw “6” and remove the box cover.
B. Let the signal cables pass through the cable glands “9”
located onto the unit body and connect the DMX signal
cables to the pin “10”.
The connection of the cable to the unit must be performed re-
specting the label next to the terminal box, while from the end
of the DMX controller the connection must respect the follow-
ing table:
pin 1 = ND
pin 2 = data -
pin 3 = data +
Size and connection scheme of the DMX cable are shown in
the following picture.
6
6
10
9
Pin 1: GND
Pin 2: DATA-
Pin 3: DATA+
ø4 MIN
ø8 MAX
DMX cable size
English 25
C. Close the unit again by tighten the screw “6” previously re-
moved.
4.5 Gobo installation
The gobo size is Ø53.3 mm with image Ø40 mm.
The size is compatible with standard “D size”.
A. Untighten the screw “11” and remove the lower cover.
B. Untighten the knob “12” and move sideways the lenses.
Warning!
All data wires must be isolated one from another, from the shield and from the metal housing of the connectors.
Pin number 1 of the housing is not to be connected to the electric ground of the unit.
Insert a 120 Ω resistor connected to Data+ and Data- in the last unit.
6
11
12
26 English
C. Insert the gobo in the gear “13”.
D. Insert the rubber gobo holder “14”.
E. Block the gobo by using the spring “15”.
F. Close the unit again by tighten the screw “11” previously re-
moved.
13
14
15
11
English 27
4.6 Focus and zoom
A. Untighten the screw “11” and remove the lower cover.
B. Move the lenses on order to adjust the beam angle and then
tighten the knob “12”.
C. Close the unit again by tighten the screw “11” previously
removed.
Goboled 80 D produces an manually adjustable beam between 19° and 35°.
11
12
11
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Proyector de Griven
Griven
Griven Dune MK2 AL4850 Manual de usuario
Griven
Griven RISALTO 150 Manual de usuario
Griven
Griven Dawn AL1202 Manual de usuario
Griven
Griven Parade L1 Manual de usuario
Griven
Griven Powershine MK2 D Manual de usuario
Griven
Griven Zaphir AL4800 Manual de usuario
Griven
Griven DANUBE Manual de usuario
Griven
Griven SKY ROSE 1200 Manual de usuario
Griven
Griven GR 0025 HMI 2500 Manual de usuario
