Grimani Systems Delta Speaker Manual de usuario

61 Galli Drive, Suite B |Novato, CA 94949, USA |+1.415.883.1476 |info@grimanisystems.com |www.grimanisystems.com

Delta Speaker

Installation and Operation Manual

April 25, 2017

Delta Speaker

Installation Manual

1. Unpack the speaker

a. Place shipping box flat, with model and serial number label at the top.

b. Cut packing tape, open the carton, and remove the accessories that are packed into the top foam

protection layer. These include the power cable, the four mounting brackets, and a pack of screws.

c. Carefully remove the top layer of protection foam.

d. Carefully remove the speaker from the carton. Do NOT pull it out by the waveguide

e. Keep the box and packing material in case you need to ship it back for returns, maintenance or

upgrades.

2. Prewire. Power, Signal, and Control network should be prewired to each Delta speaker

a. Power: The Delta is an active speaker with built-in signal processing and amplification. It requires

about 600 Watts of available AC power in the range from 100V to 250V. We recommend prewiring

one 120V-20A circuit, or a 220 / 240V –15A for each group of three Delta speakers, with either a

quad box near the three speakers, or a duplex near each speaker.

b. Audio Signal: The Delta takes Analog Balanced audio signal over twisted pair with braided shield

XLR cable. It is best to prewire for it. An “RCA” unbalanced signal can also be fed to the Delta,

ideally through a balancing transformer as close to the source as possible. Jensen Transformer

makes very good balance adapter transform units. Note that even for unbalanced analog audio

sources it is best to use a twisted pair with shield cable. See the connection section below for

termination recommendations. It is also possible to use Cat5 or Cat 6 cabling to feed a balanced

signal to the Delta, using XLR connectors at the speaker end. A few manufacturers, including

MuxLab (model 500028) and Audio Control (BLD-10) make unbalanced to Cat5 converters which

can be used for unbalanced feeds (see Appendix 2). There may be residual noise interference in

environments with a lot of radio frequency noise. Contact Grimani Systems Technical Support for

further details.

c. Control signal: The Delta is controlled and monitored through a USB interface. Using a USB to Cat5

converter, you can prewire with either Cat5, Cat5e, Cat6, Cat6a cabling from a central location to the

speaker, and add the converter unit at the speaker location. Terminate the Cat5 cables at a patch

panel at the equipment rack or other room location accessible during calibration. In all cases prewire

using Keystone punch-down connectors at wall plates or rackmount locations at the rack and

speaker locations. Test the connection using a certification meter to assure quality of connection and

bandwidth. The last interface should be accomplished with factory terminated and certified patch

cables.

3. Mounting Bracket. The Delta is designed to be installed on a wall, using the supplied the four supplied

hanging bracket. For placement behind acoustically transparent screens, paint

the brackets flat black before installation in order to control light refelctions.

a. Place the speakers correctly in the room. Set the speaker position on the

wall based on several factors: Position spread relative to the listener;

position relative the screen edge or center; boundary reflection conditions.

Set the height such that the middle of the waveguide is 6 inches above

seated ear height, or at the middle of the screen. Grimani Systems

Technical Support can assist with determining the best position upon

request.

b. The wall fastener location of the top pair of brackets will be 8 inches (203

mm) below the top of the waveguide, and 6-3/8” inches (162 mm) from

the center of the speaker. See diagram below.

c. The wall fastener location of the bottom pair of brackets will be 23.25 inches (591 mm) below the

top of the waveguide, and 10.5 inches (267mm) from the center of the speaker. See diagram below.

d. Install the four vibration isolation L brackets on the speaker, using the supplied screws (#6 x 1/2”).

Do not overtighten the screws in order to avoid stripping them.

e. Mark four wall hole locations for the mounting bracket, based on a. and b. above. Use the bracket as

a template, and make sure that it is vertical by using a bubble level.

f. Choose appropriate fasteners. The Delta weighs 35 lbs (16kg), so each fastener will need to be rated

for 9 pounds (4kg) each. For sheetrock walls, we suggest using EZAnchors and their associated

screws. For Concrete walls, we suggest using good quality wall anchors and screws. For plywood

surfaces, wood screws in a size 8 (4mm) and above will work well.

g. Holding the speaker from the wood cabinet (NOT the waveguide), pick it up and hold it in place while

driving the four screws through the large bracket hole into the wall. Make sure that the speaker is

properly centered.

h. Speaker aiming: The speaker can be aimed up or down by adding a shim behind the top or bottom

brackets.

23.25”

8”

6 3/8”

10.5”

4. Connections

a. Power: The Delta ships with a 9 foot (2.75m) long locking detachable IEC power cable. The receptacle

is on the connector plate at the bottom of the speaker. Plug the cable there, then to the mains

outlet. To remove the ICE cable from the speaker, pull back the red locking pin before easing out the

plug. After powering up the speaker, it will go through a few seconds of start-up sequence. There is

no standby switch.

b. Audio signal. Plug in the audio feed:

- - For Analog balanced over twisted pair cable with shield, terminate the cable to a male XLR plug,

using Pin 2 for +, Pin3 for -, and Pin 1 for ground/shield. Connect the XLR plug into the XLR Analog

female input, labeled (INPUT). See Appendix 1.

- For Analog unbalanced sources, it is also best to pre-wire with twisted pair with shield. On the

source side, use a balancing transformer (either passive or active). If a balancing transformer isn’t

available, connect the + signal to the + wire (usually Red) of the pair, and connect the source

ground to the –wire (usually Black) of the pair. On the speaker side, terminate the cable with a

male XLR plug, with Pin 2 for the + wire, Pin3 for - wire, and Pin 1 for the shield of the wire (See

Appendix 1). If you used regular coaxial wire, from the source, terminate the wire to a Male XLR

plug with Pin 2 for the + wire, Pin3 and Pin 1 for the shield of the wire. If there is a hum loop, try

disconnecting Pin 1 on the XLR plug. If the coaxial wire is already terminated with and RCA

connector, you can use a female-to-male XLR converter plug.

Power

Main

Level

Analog

Audio In

USB Control Port

Processing

Preset

Select

Analog Audio

through Out

You can also use Cat5 cable with a balancing converter unit such as the MuxLabs 500028, as shown

in Appendix 2, or the Audio Control BLD-10.

c. Control signal:

- The Delta is controlled and monitored through a USB interface (see 2.c above.). Assuming that you

prewired to a wall-mounted or rack-mounted keystone punch-down RJ45 receptacle, connect a

premade factory-terminated and certified patch cable, to the Cat5 to USB adapter, and plug this to

the speaker. Tie back the USB cable with a zip tie in order to prevent it from falling off. If you didn’t

prewire to a punch-down receptacle, carefully terminate the network cable with a male RJ45, using

EIA T568B standard, and ensure proper connection and strain relief. Test the connection with a

certification tester to ensure proper connectivity.

d. The Delta has an analog audio through output on a male XLR in order to feed another speaker

5. Settings

a. AC Voltage is automatically set for a range from 100V AC to 250V AC. There is nothing to set.

b. EQ preset. The Delta ships with a response curve that is voiced for the most typically neutral voicing

in-room. This is mostly flat anechoic response for both the axial and sound power frequency

response. This is stored into Presets 1 through 4. After installation, you can equalize and voice each

speaker to match the room, and store one or more EQ curves in one of the four presets. You can

switch between the presets by pressing the preset button on the connector plate at the bottom of

the speaker.

c. Input Volume. Set the volume knob to middle detent gain (0dB).

d. DSP programming. The Delta speaker includes a DSP engine with 5 bands of response tailoring, plus

several other signal processing functions. These are programmed through a computer application,

and requires advanced control by a factor trained professional. Contact Grimani Systems for DSP

programming and system calibration services.

6. Remote Monitoring

The Delta speaker can be tested and verified from a remote location. You will need to dedicate a small

Windows computer to be left enabled on an internet connection. It will need to run the Grimani Systems

Armonia control application as well as a remote desktop application. Both of these can be set up by a

Grimani Systems factory technician.

7. Limited Warranty

The Delta is warrantied to be free of manufacturing defects for a period of two years from the date of

purchase. This limited warranty does not apply to failures due to misuse, excessive sound pressure,

damage from handling and carriage, or any other defects that are outside the control of Grimani

Systems, LLC. Any warranty claim will need to be made directly with Grimani Systems, or through one of

its authorized dealers. An RMA number will need to be issued before any return is authorized.

Appendix 1

Balanced Analog Wire connection

Unbalanced to Balanced Analog Wire connection

Appendix 2

MuxLab 500028 Wiring Diagram

For use in driving unbalanced signals to XLR inputs of speakers

One Balun can be used to drive two speakers

From White

RCA Input

XLR Male to

speaker 1 input

Pin 3

Pin 1

Pin 2

Pin 3

Pin 1

Pin 2

XLR Male to

speaker 2 input

Cat5

Cable

From Red

RCA Input

Tabla de contenidos

Otros manuales de Oradores de Grimani Systems

Grimani Systems

Grimani Systems Alpha Manual de usuario

Manuales populares de Oradores de otras marcas

argon audio

argon audio IE20 Manual de usuario

Denon

Denon SC-N7 Manual de usuario

Gemline

Gemline Ace 3952 Manual de usuario

Focal

Focal ON WALL 300 Manual de instrucciones

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manual de usuario

SoundLogic

SoundLogic BCCS-6/6395 Manual de usuario

Peavey

Peavey DTH 218 Manual de usuario

Avantree

Avantree Pluto Air Manual de usuario

Morel

Morel Integra Series INTEGRA OVATION 4 Manual de usuario

Oppo

Oppo SONICA Manual de usuario

Bose

Bose SoundLink Wireless Music System Manual de usuario

Rocksteady

Rocksteady Stadium Manual de usuario

Bowers & Wilkins

Bowers & Wilkins 4 Manual de usuario

Sonance

Sonance SONOS OUTDOOR Series Manual de usuario

Electro-Voice

Electro-Voice EVID FM4.2 Manual de usuario

Pioneer

Pioneer XW-HTD630 Manual de usuario

Onn

Onn BWA16AA002 Manual de usuario

HP GL313AA - USB Speakers PC Multimedia Manual de usuario