GreenWorks LME470 Manual de usuario

P0803119-02

GWK 2*24V Mower

2512807

技术要求：

@此为P0803119-01编号升级版本，增加UKCA

2.内容见电子档；保证色块朝外；

3.单色印刷，要求无色差、无污点；

4.胶装，裁切均匀、无连页；

5.以封样为准。

1.材质要求：封面封底120g双胶纸：4P; 内页60g双胶纸：184P;

85%本白

常州格力博集团

说明书

张君

陈丽

周艳

王小妮

李海平

21.08.12

版本号

重要度等级

日期

工艺

审核

校对

设计

标记处数签名日期

阶段标记视角标记重量比例

批准

审定

标准化

日期

更改文件号

SCALE: A5

210mm

145mm

6.料件需符合格力博HSF文件(编号：GLB-CGR-146) 里关于环保和有害物质的具体要求。

ＡB

@ 1

LME470

OPERATOR MANUAL / BEDIENUNGSHANDBUCH / MANUAL DEL OPERARIO /

MANUALE DELL’OPERATORE / MANUEL OPÉRATEUR / MANUAL DE UTILIZAÇÃO /

KASUTUSJUHEND

OriginalInstructions / Übersetzung der Originalanweisungen/ Traducciónde las instrucciones originales/ Traduzione delle istruzioni originali/ Traductiondes

instructions d'origine/ Traduzidoa partir das instruções originais/ Vertaling van de originelegebruiksaanwijzing/ Переводоригинальных инструкций/

Alkuperäisten ohjeiden käännös/ Översättning avoriginalinstruktionerna/ Produsentens instruksjoner/ Oversættelse afde originale vejledninger/ Tłumaczenie

oryginalnej instrukcji / Překlad originálníhonávodu/ Prekladoriginálneho návodu/ Prevodoriginalnih navodil/ Prijevod izvornih uputa/ Az eredeti utasítás

fordítása/ Traducere ainstrucţiunilor originale/ Превод на оригиналните инструкции/ Αυθεντικέςοδηγίες / / Orijinal

Talimatların Tercümesi // OriginaliosInstrukcijosvertimas/ Instrukciju tulkojums no oriģinālvalodas/ Originaalkasutusjuhendi tõlge

GD24X2LM46SP

P0803119-02 Rev B

Name and address of the manufacturer:

Name: GLOBGRO AB

Globe Group Europe

Address: Riggaregatan 53, 211 13 Malmö Sweden

Name and address of the Authorized representative:

Name: Garden Equipment Ltd

Address: 3a Groveley Road, Christchurch, Dorset, BH23 3HB, UK

Name and address of the person authorised to compile the technical file:

Name: Simon Del-Nevo

Address: 3a Groveley Road, Christchurch, Dorset, BH23 3HB, UK

Here with we declare that the product

Category: Lawn Mower

Model: GD24X2LM46SP (LME470)

Serial number: See product rating label

Year of Construction: See product rating label

• is in conformity with the relevant provisions of the Supply of Machinery (Safety) Regulations 2008.

• is in conformity with the provisions of the following other UK legislation:

• Electromagnetic Compatibility Regulations 2016

• Noise Emission in the Environment by Equipment for use Outdoors Regulations 2001

• The Restriction of the Use of Certain Hazardous

• ubstances in Electrical and Electronic Equipment Regulations 2012

Furthermore, we declare that the following standard have been used:

BS EN 60335-1, BS EN 60335-2-77, BS EN 62233, BS EN 55014-1, BS EN 55014-2,

BS EN ISO 3744, ISO 11094, BS EN 62321-3-1, BS EN 62321-4, BS EN 62321-5,

BS EN 62321-6, BS EN 62321-7-1, BS EN 62321-7-2, BS EN 62321-8

Conformity assessment method to Annex E Noise Emission in the Environment by Equipment for

use Outdoors Regulations 2001.

Measured sound power level 90 dB(A)

Guaranteed sound power level 92 dB(A)

Place, date: Christchurch, Dorset, UK 07.06.2021 Signature: Ted Qu, Quality Director

DECLARATION OF CONFORMITY (UK)

1 Description.........................................4

1.1 Purpose.............................................................. 4

1.2 Overview........................................................... 4

2 Safety.................................................. 4

3 Installation......................................... 4

3.1 Unpack the machine.......................................... 4

3.2 Unfold the lower handle.................................... 4

3.3 Install the upper handle .....................................4

3.4 Install the grass catcher......................................5

3.5 Install the mulch plug........................................ 5

3.6 Install the side discharge chute..........................5

3.7 Set the blade/cutting height............................... 5

3.8 Install the battery pack.......................................5

3.9 Remove the battery pack................................... 5

4 Operation........................................... 5

4.1 Start the machine............................................... 5

4.2 Stop the machine............................................... 6

4.3 Operate the self-propel system.......................... 6

4.4 Empty the grass catcher.....................................6

4.5 Operate on slopes...............................................6

4.6 Operation tips.................................................... 6

5 Maintenance.......................................6

5.1 General maintenance......................................... 6

5.2 Replace the blade...............................................7

5.3 Store the machine.............................................. 7

5.4 Stand the machine on end..................................7

6 Troubleshooting.................................7

7 Technical data....................................8

8 Warranty............................................8

9 EC Declaration of conformity..........8

English EN

1 DESCRIPTION

1.1 PURPOSE

This machine is used for domestic lawn mowing. The cutting

blade must be approximately parallel to the ground. All four

wheels must touch the ground while mowing.

1.2 OVERVIEW

Figure 1~12

1Bail switch

2Start button

3Upper handle

4Lower handle

5Rear discharge flap

6Height adjustment lever

7Battery compartment flap

8Side discharge flap

9Self-propel drive lever

10 Speed control button

11 Grass catcher

12 Lower handle knob

13 Mulch plug

14 Side discharge chute

15 Bolt

16 Upper handle knob

17 Battery pack

18 Battery release button

19 Safety key

20 Mounting screw

21 Spacer

22 Blade

23 Grass catcher hook

24 Storage switch

2 SAFETY

WARNING

Make sure that you follow all safety instructions.

Refer to Safety Manual.

3 INSTALLATION

WARNING

Do not use accessories that are not recommended by the

manufacturer.

WARNING

Do not put in the safety key or the battery pack until you

finalised the assembly of all the parts.

3.1 UNPACK THE MACHINE

WARNING

Make sure that you correctly assemble the machine before

use.

WARNING

• If parts of the machine are damaged, do not use the

machine.

•If you do not have all the parts, do not operate the

machine.

• If parts are damaged or missing, contact the service

center.

1. Open the package.

2. Read the documentation provided in the box.

3. Remove all the unassembled parts from the box.

4. Remove the machine from the box.

5. Discard the box and packing material in compliance with

local regulations.

WARNING

For your personal safety, do not insert battery before the

tool is assembled completely.

3.2 UNFOLD THE LOWER HANDLE

Figure 2

1. Pull and turn the handle knobs 90°.

2. Unfold the lower handle.

3. Line up the handle knobs in one of the three positions on

the brackets.

4. Turn the handle knobs 90° until they engage the holes in

the brackets.

NOTE

Make sure that the two handle knobs are in the same

position.

WARNING

Do not make damage to the cables when you fold or unfold

the handle.

3.3 INSTALL THE UPPER HANDLE

Figure 3

1. Align the holes in the upper handle and the lower handle.

2. Put the bolts through the holes.

English

3. Tighten the knobs onto the bolts.

4. Do the same operation on the other side.

3.4 INSTALL THE GRASS CATCHER

Figure 4

1. Remove the mulch plug.

2. Remove the side discharge chute.

3. Open the rear discharge flap and hold it.

4. Hold the the grass catcher by its handle and engage the

hooks on the door rod.

5. Close the rear discharge flap.

3.5 INSTALL THE MULCH PLUG

Figure 5.

1. Remove the grass catcher.

2. Open the rear discharge flap and hold it.

3. Hold the mulch plug by its handle and fit it in the

discharge chute.

4. Close the rear discharge flap.

3.6 INSTALL THE SIDE DISCHARGE

CHUTE

Figure 6

CAUTION

When you use the side discharge chute,

•Do not install the grass catcher.

• Keep the mulch plug installed.

1. Open the side discharge flap and hold it.

2. Line up the recesses of the side discharge chute below the

pivot.

3. Close the side discharge flap.

3.7 SET THE BLADE/CUTTING

HEIGHT

The machine can be set to different blade/cutting heights.

Figure 7

1. Pull the height adjustment lever rearward to increase the

blade/cutting height.

2. Push the height adjustment lever forward to decrease the

blade/cutting height.

3.8 INSTALL THE BATTERY PACK

Figure 8

WARNING

• If the battery pack or charger is damaged, replace the

battery pack or the charger.

• Stop the machine and wait until the engine stops before

you install or remove the battery pack.

• Read, know, and follow the instructions in the battery

and charger manual.

WARNING

USE ONLY 24V BATTERY. DO NOT USE DUAL-

VOLTAGE 24/48V BATTERY.

NOTE

Both batteries should be installed into the compartments in

order to start the machine.

1. Open the battery flap.

2. Align the lift ribs on the battery pack with the grooves in

the battery compartment.

3. Push the battery pack into the battery compartment until

the battery pack locks into place.

4. When you hear a click, the battery pack is installed.

5. Do the same operation with the other battery.

6. Close the battery flap.

NOTE

The motor starts only when you put in the safety key.

3.9 REMOVE THE BATTERY PACK

Figure 8

1. Open the battery compartment flap

2. Remove the safety key.

3. Push and hold the battery release button.

4. Remove the battery pack from the machine.

4 OPERATION

WARNING

Wear eye protection during operation.

4.1 START THE MACHINE

Figure 9

1. Put in the safety key.

2. Push and hold the start button.

3. While you hold the start button, pull the bail switch in the

direction of the handle bar.

4. Release the start button to start the machine.

English EN

4.2 STOP THE MACHINE

1. Release the bail switch to stop the machine.

WARNING

Wait until the blades fully stop before you start the machine

again. Do not quickly turn the machine off and on.

WARNING

Always remove the safety key and battery pack after you

complete the work.

4.3 OPERATE THE SELF-PROPEL

SYSTEM

Figure 10

1. Start the machine.

2. While you hold the bail switch, push the self-propel lever

in the direction of the handle bar.

3. Hold the bail switch and the self-propel lever at the same

time with your right hand.

4. Adjust the speed control button with your left hand.

• Push the speed control button in the direction of the

Cougar Symbol to increase the speed.

• Pull the speed control button in the direction of the

Turtle Symbol to decrease the speed.

5. Release the self-propel lever to close the self-propel

system.

4.4 EMPTY THE GRASS CATCHER

1. Stop the machine.

2. Remove the safety key.

3. Remove the battery pack.

4. Open the rear discharge flap and hold it.

5. Hold the grass catcher by its handle and unhook it from

the door rod.

6. Close the rear discharge flap.

7. Empty the grass catcher.

4.5 OPERATE ON SLOPES

WARNING

Do not mow on the slopes with incline more than 15°. If

you are not comfortable, do not mow on a slope.

WARNING

Please keep a low self-propelled speed when you mow on a

slope.

• Do not go up and down on a slope, mow across the face

of the slope. Be careful when you change the direction on

a slope.

• Monitor the holes, ruts, rocks, and other hidden objects

that can cause you to fall. Remove all obstacles such as

rocks and tree limbs.

•Make sure that your footing is stable. If you are out of

balance, release the bail switch immediately.

• Do not mow near drop-offs, ditches, or embankments.

4.6 OPERATION TIPS

• Do not try to override the operation of the start button or

bail switch.

•Do not tilt the machine when you start it.

• Do not put hands or feet near or below the turning parts.

• Keep the discharge chute clean.

• Do not cut wet grass.

• Higher blade height is necessary for new or thick grass.

• Clean the bottom of the mower deck after each use.

Remove grass clippings, leaves, dirt, and other debris.

5 MAINTENANCE

WARNING

Remove the safety key and battery pack from the machine

before maintenance.

WARNING

Keep the motor and battery pack free from grass, leaves or

too much grease.

CAUTION

Use only approved replacement parts.

CAUTION

Do not let brake fluids, gasoline, petroleum-based materials

touch the plastic parts. Chemicals can cause damage to the

plastic, and make the plastic unserviceable.

CAUTION

Do not use strong solvents or detergents on the plastic

housing or components.

NOTE

Recommended tightening torque (blade): 33-37 Nm.

5.1 GENERAL MAINTENANCE

• Before each use, examine the machine for damaged,

missing, or loose parts such as screws, nuts, bolts and

caps.

•Tighten correctly all the fasteners and caps.

• Clean the machine with a dry cloth. Do not use water.

English

5.2 REPLACE THE BLADE

Figure 11

WARNING

Use only approved replacement blades.

WARNING

Wear heavy gloves or wind cloth around the blade when

you touch the blade.

1. Stop the machine.

2. Make sure that the blades fully stop.

3. Remove the safety key and battery pack.

4. Turn the machine to its side.

5. Use a piece of wood to prevent the movement of the

blade.

6. Remove the mounting screw and spacer with a wrench or

socket.

7. Remove the blade.

8. Install the new blade. Make sure that the arrows engage

the holes in the blade.

9. Put in the mounting screw and spacer and tighten them.

5.3 STORE THE MACHINE

• Remove the safety key.

•Remove the battery pack(s).

• Clean the machine before storage.

• Make sure the motor is not hot when you store the

machine.

• Make sure that the machine does not have loose or

damaged parts. If it is necessary, follow these

instructions:

• Replace the damaged parts.

• Tighten the bolts.

• Speak to a person at an approved service center.

• Store the machine in a dry area.

• Make sure that children cannot come near the machine.

5.4 STAND THE MACHINE ON END

Figure 12

1. Remove the grass catcher.

2. Pull and turn the handle knobs 90°.

3. Fold down the handle.

4. Turn the handle knobs 90° to lock the handle into

position.

5. Stand the machine on end and make sure that the brackets

touch the floor.

Storage Switch

The machine has a storage switch that prevents its startup in

the storage position.

It is necessary to remove the safety key and the battery pack

to prevent accidental startup or unapproved use. The storage

switch does not replace this function.

6 TROUBLESHOOTING

Problem Possible cause Solution

The handle is not

in position.

The bolts are not

engaged correctly.

Adjust the height

of the handle and

make sure that the

knobs and bolts

are aligned cor-

rectly.

The machine does

not start.

The battery ca-

pacity is low.

Charge the battery

pack.

The bail switch is

defective.

Replace the bail

switch.

The safety key is

not put in.

Put in the safety

key.

The machine cuts

grass unevenly.

The lawn is rough. Examine the mow-

ing area.

The blade height is

not set correctly.

Adjust the blade/

cutting height to a

higher position.

The machine does

not mulch correct-

ly.

Wet grass clip-

pings attach to the

deck.

Wait until the

grass dries before

mowing.

The mulch plug is

missing.

Install the mulch

plug.

The machine is

hard to push.

The grass is too

tall, or the blade

height is too low.

Increase the blade/

cutting height.

The grass catcher

and the blade

drags in thick

grass.

Empty the grass

clippings from the

grass catcher.

There is a high vi-

bration in the ma-

chine.

The blade is un-

balanced and

worn.

Replace the blade.

The motor shaft is

bent.

1. Stop the mo-

tor.

2. Remove the

safety key and

battery pack.

3. Inspect for

damage.

4. Repair the ma-

chine before

you start it

again.

English EN

Problem Possible cause Solution

The machine stops

during mowing.

The blade height is

too low.

Increase the blade/

cutting height.

The battery pack is

out of power.

Charge the battery

pack.

The grass clip-

pings attach to the

deck or the blade.

Remove the bat-

tery pack and

check the deck.

Operation temper-

ature of the ma-

chine is too high.

Cool the machine.

* If you cannot find the solution to these problems, go to the

service center.

7 TECHNICAL DATA

Voltage 48 V

No load speed 2800 / min

Cut width 460 mm

Cut height 25 - 80 mm

Self-propelled speed 0.7-1.3 m/s

Grass catcher capacity 55 L

Weight (without battery

pack)

27.5 kg

Measured sound pressure

level

LPA= 78.1 dB(A) , K = 3

dB(A)

Guaranteed sound power lev-

LWA.d= 92 dB(A)

Vibration ≤ 2.5 m/s2 , K = 1.5 m/s2

Battery model G24B4/G24B2 and other

BAG series

Charger model G24X2UC2/G24X2UC4/

G24X2C and other CAG ser-

ies

Double-insulated construc-

tion

IPX IPX4

8 WARRANTY

(The full warranty terms and conditions can be found on

Greenworks website https://www.greenworkstools.eu)

The Greenworks warranty is 3 years on the product, and 2

years on batteries (consumer/private usage) from the date of

purchase. This warranty covers manufacturing faults. A faulty

product under warranty might be either repaired or replaced.

A unit that has been misused or used in other ways then

described in the owner’s manual might be rejected for

warranty. Normal wear, and wear parts are not considered as

warranty. The original manufacturer warranty is not affected

by any additional warranty offered by a dealer or retailer.

A faulty product must be returned to the point of purchase in

order to claim for warranty, together with the proof of

purchase (receipt).

9 EC DECLARATION OF

CONFORMITY

Name and address of the manufacturer:

Name: GLOBGRO AB

Globe Group Europe

Address: Riggaregatan 53, 211 13 Malmö, Sweden

Name and address of the person authorised to compile the

technical file:

Name: Micael Johansson

Address: Riggaregatan 53, 211 13 Malmö, Sweden

Herewith we declare that the product

Category: Lawn Mower

Model: GD24X2LM46SP (LME470)

Serial number: See product rating label

Year of Construction: See product rating label

• is in conformity with the relevant provisions of the

Machinery Directive 2006/42/EC.

•is in conformity with the provisions of the following

other EC-Directives:

• 2014/30/EU

• 2000/14/EC & 2005/88/EC

• 2011/65/EU & (EU)2015/863

Furthermore, we declare that the following parts, clauses of

harmonised standards have been used:

• EN 60335-1, EN 60335-2-77, EN 62233, EN ISO 3744,

EN 55014-1, EN 55014-2, ISO 11094, IEC 62321-3-1,

IEC 62321-4, IEC 62321-5, IEC 62321-6, IEC

62321-7-1, IEC 62321-7-2. IEC 62321-8

Conformity assessment method to Annex VI Directive

2000/14/EC.

Measured sound power level LWA: 90 dB(A)

Guaranteed sound power level LWA.d : 92 dB(A)

Place, date: Malmö,

08.08.2021

Signature: Ted Qu, Quality Director

English

English EN

Otros manuales para LME470

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Cortacésped de GreenWorks

GreenWorks

GreenWorks GD40SC38II Manual de usuario

GreenWorks

GreenWorks MO48L2211 Manual de usuario

GreenWorks

GreenWorks MO10B00 Manual de usuario

GreenWorks

GreenWorks LMF318 Manual de usuario

GreenWorks

GreenWorks MO40L4413 Manual de usuario

GreenWorks

GreenWorks 25322 Manual de usuario

GreenWorks

GreenWorks LMC403 Manual de usuario

GreenWorks

GreenWorks Elite M-210-SP-T Manual de usuario

GreenWorks

GreenWorks G40LM40 Manual de usuario

GreenWorks

GreenWorks GD24LM33 Manual de usuario

GreenWorks

GreenWorks LMF320 Manual de usuario

GreenWorks

GreenWorks MO48L520 Manual de usuario

GreenWorks

GreenWorks POWERALL MO48L4212 Manual de usuario

GreenWorks

GreenWorks GLM801602 Manual de usuario

GreenWorks

GreenWorks 25222 Manual de usuario

GreenWorks

GreenWorks GD60LM46SP Manual de usuario

GreenWorks

GreenWorks LMA123 Manual de usuario

GreenWorks

GreenWorks MO80L08 Manual de usuario

GreenWorks

GreenWorks G40LM35K2X Manual de usuario

GreenWorks

GreenWorks Optimow 15 Manual de usuario

GreenWorks

GreenWorks MO09B01 Manual de usuario

GreenWorks

GreenWorks Optimow 10 Manual de usuario

GreenWorks

GreenWorks LMF317 Manual de usuario

GreenWorks

GreenWorks MO40L04 Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario