Greenlee 713 Manual de usuario
INSTRUCTION MANUAL
Read and understand all of the instructions and
safety information in this manual before operating
or servicing this tool.
999 4220.8 © 2019 Greenlee Tools, Inc. IM 1542 REV 2 1019
713
Plumbers Stud Punch
Greenlee Tools, Inc. 24455 Boeing Dr., Rockford, IL 61109-2988 815/397-7070
713 Plumbers Stud Punch
IMPORTANT SAFETY INFORMATION
SAFETY
ALERT
SYMBOL
This symbol is used to call your attention to hazards
or unsafe practices which could result in an injury or
property damage. The signal word, defined below,
indicates the severity of the hazard. The message
after the signal word provides information for
preventing or avoiding the hazard.
KEEPTHIS MANUAL
Hazards or unsafe practices which, if not avoided,
MAY result in injury or property damage.
Hazards which, if not avoided, COULD result in
severe injury or death.
Immediate hazards which, if not avoided, WILL result
in severe injury or death.
Do not add extensions (cheaters) to the handles.
Using excessive force can result in injury or damage
to the tool. If excessive force is required to complete
a punch, verify that the type and thickness of
material do not exceed the capacity of the tool.
Electric shock hazard. This is not
an insulated tool. Contact with live
circuits can result in severe injury
or death.
Wear eye protection when using
this tool.
Failure to wear eye protection can
result in serious eye injury from
flying debris.
• Inspect the tool prior to use. Replace worn,
damaged, or missing components with Greenlee
replacement parts. A damaged or improperly
assembled tool can break.
•
Use this tool for manufacturer’s intended use only.
Use other than that which is described in this
manual can result in injury or damage to the tool.
Do not use on heavier than 20 gauge mild steel.
Greenlee Tools, Inc. 34455 Boeing Dr., Rockford, IL 61109-2988 815/397-7070
713 Plumbers Stud Punch
Operation
1. Hold the C-head handle securely. Push the slotted
handle forward, using the slot to extend the handle.
2. Spread the handles apart to lift the punch and clear
the opening in the C-head.
3. Position the punch on the metal stud.
4. Pull the slotted handle back, using the slot.
5. When the handle reaches the end of the slot and
the punch shaft and link are at their closest position,
punch the hole.
6. Push the slotted handle forward using the slot to
raise the punch in the C-head to clear and remove
the tool from the stud.
Note: This tool will punch to its rated capacity with
approximately 200 newtons (45 pounds) of handle
force. If excessive force is required, stop and inspect
the tool and the material.
Maintenance
Lubricate all moving parts with a lightweight oil or
Molykote®lubricant.
Description
The Greenlee 713 Plumbers Stud Punch is intended to
punch round holes in 20 gauge steel studs.
The 713 punches a 66.9 mm (2-5/8") diameter hole to
accommodate a 2" inside diameter PVC white or CPVC
gray schedule 40 pipe.
Safety
Safety is essential in the use and maintenance of
Greenlee tools and equipment. This instruction manual
and any decals on the tool provide information for
avoiding hazards and unsafe practices related to the
use of this tool. Observe all of the safety information
provided.
Purpose
This instruction manual is intended to familiarize opera-
tors and maintenance personnel with the safe operation
and maintenance procedures for the Greenlee 713
Plumbers Stud Punch. This manual should be kept
available to all operating and maintenance personnel.
Molykote is a registered trademark of Dow Corning
Corporation.
4455 Boeing Dr., Rockford, IL 61109-2988 815/397-7070
713 Plumbers Stud Punch
ExplodedView and Parts List
1
2
3
4
6
8
7
14
13
10 1211
5
GREENLEE
15
713
9
UPC NO. PART
KEY NO. DESCRIPTION QTY.
1 905 0617.0 Screw, 1/4–20 UNC set.............................1
2 501 0465.9 C-head unit (includes one of item 14) .......1
3 500 8379.1 Die .............................................................1
4 500 8377.5 Punch ........................................................1
5 905 5315.2 Pin, spiral, .312 x .875...............................1
6 500 8375.9 Link............................................................1
7 905 4847.7 Nut, 3/4–16 hex .........................................1
8 500 8376.7 Shaft, punch ..............................................1
9 905 5316.0 Pin, groove, .312 x 1.75 ............................1
10* 905 1762.8 Screw, socket head, 6–32 x .38 ................2
11* 500 8382.1 Standoff .....................................................1
12* 500 8383.0 Washer ......................................................2
13 501 0466.7 Handle unit (includes one of item 14)........1
14 905 1174.3 Grip............................................................2
15
78-3310-
50617
10465
08379
08377
55315
08375
54847
08376
55316
51762G
08382
08383
10466
51174
08384 500 8384.8 Decal, identification ...................................1
* 10467 501 0467.5 Pin kit (includes items marked with an asterisk)
Printed in the USA
Greenlee Tools, Inc.
4455 Boeing Drive, Rockford, IL 61109-2988 USA
Customer Service (International): 815/397-7070 • Fax: 815/397-9247
Customer Service (North America): 800/435-0786 • USA Fax: 800/451-2632, 815/397-1865
Canada Fax: 800/524-2853
www.greenlee.com
Otros manuales de Herramientas de Greenlee
Greenlee
Greenlee 660QA Manual de usuario
Greenlee
Greenlee K1GL Manual de usuario
Greenlee
Greenlee 645-5/8 Manual de usuario
Greenlee
Greenlee EK1550FLT Manual de usuario
Greenlee
Greenlee 709 Manual de usuario
Greenlee
Greenlee JRF-4EPR Manual de usuario
Greenlee
Greenlee 1904Pg Manual de usuario
Greenlee
Greenlee 881MBTS Manual de usuario
Greenlee
Greenlee LS60L Manual de usuario
Greenlee
Greenlee G1 Versi-Tugger Manual de usuario
Greenlee
Greenlee K1GL Manual de usuario
Greenlee
Greenlee 45658 Manual de usuario
Greenlee
Greenlee 52061455 Guía del usuario
Greenlee
Greenlee ULTRA GLIDER UG5 Manual de usuario
Greenlee
Greenlee CR25 Manual de usuario
Greenlee
Greenlee K30GL Manual de usuario
Greenlee
Greenlee 1800 Mechanical Bender Manual de usuario
Greenlee
Greenlee 767 Manual de usuario
Greenlee
Greenlee HKL1232 Manual de usuario
Greenlee
Greenlee G2090/03560 Manual de usuario
