Greenlee 93-70 Guía del usuario

DIGITAL MULTI-TESTER

OPERATION, MAINTENANCE AND

SAFETY INSTRUCTIONS

93-70/00628

P–HD–H

R S T

BAT

AC MK

KHz

°C °F

GREENLEE



Cat./UPC No. 93-70/00628

Read and understand this material before operating.

Failure to understand how to safely operate the tester

could result in an accident causing serious injury or

death. This tester should only be operated by qualified

personnel.

Español; p. 17

Français; p. 33

DANGER

HIGH

VOLTAGE

CAUTION

SAFETY INFORMATION

Follow operating instructions carefully.

Contact with live circuits can cause serious injury or death.

Do not use meter if wet or damaged.

To avoid electric shock, do not perform any service or maintenance other

than that described in these instructions. Always disconnect test leads

before opening case.

To avoid personal injury and possible damage to the meter, never connect

a source of voltage with the rotary function switch in Ω(ohms) position.

To avoid electric shock, hazard or damage to meter do not apply voltage

exceeding the over voltage rating of the function between any terminals of

the instrument.

Failure to observe these warnings may result in serious injury or death!

• Observe proper safety precautions when working with voltages above 50V DC or 25V AC

RMS. These voltage levels pose a shock hazard to the user.

• If the meter is used near equipment that generates electro-magnetic interference the

display may be unstable or indicate incorrect measurement values.

• Use only the correct, properly rated fuses, when replacement is necessary.

• Disconnect test leads from items being tested before changing rotary function selector.

• Do not store instrument in hot, 135°F (57°C) and above, or humid areas.

• Replace weak or discharged battery as soon as it is detected (see Maintenance

information).

• Use only for specified use and capacities.

Failure to observe these warnings may result in minor injury and/or

damage to the instrument!

PACKING LIST

The following items should be packed with the multimeter unit:

Item # Part # Qty. Description

1 500 0409.3 2 Test Leads - 1 Black, 1 Red

2 500 0842.0 3 RST Leads, 1 ea. - Black, Red, Yellow

3 999 1961.3 1 IM-1245, Instruction Manual

4 500 0841.2 1 Protective Holster

93-70 Digital Multi-Tester

GREENLEE



Cat./UPC No. 93-70/00628

P–HD–H

R S T

KHz

°C °F

BAT

AC MK

Fig. 1

FEATURES (Fig. 1)

•Digital Display - 3-1/2 digit LCD read-out, 1999 maximum reading; indicates AC voltage and

current, DC voltage and current, resistance, frequency, diode, continuity, temperature and

phase sequence. Also indicates overload (OL), low battery (BAT) and automatic polarity.(A)

•Power Switch - Turns unit on and off. (B)

•Display Hold (D-H) - Captures a stable measurement and holds it on the display.*(C)

•Peak Hold - Displays maximum reading when testing AC voltage or current.* (D)

•Rotary Selector Switch - Selects function and test range. (E)

•Temperature Probe Connection - For K-Type probe connection for temperature measure-

ment. (F)

•VΩInput Terminal - For DC and AC voltage, resistance, frequency, diode, continuity and

phase sequence indicator (using Black Lead in T terminal). (G)

•COM Input Terminal - The ground input terminal or the input terminal for phase sequence

indicator (using yellow lead in S terminal). (H)

•mA, µAInput Terminal - For current measurement, plus input terminal for phase sequence

indicator (using red lead in R terminal). (I)

•10A Input Terminal - For current measurement above 200mA and below 10A, positive (+)

terminal. (J)

•Auto Off - Tester will automatically shut off after approximately 26 minutes.

* See Feature Usage in OPERATION section for information about using these features.

OPERATION

Preparation for Measurement

1. Set rotary switch to desired function before connecting test leads to item being tested.

2. Always disconnect test leads from item being tested before changing the rotary function

selector.

3. If the unit is used near equipment that generates electro-magnetic interference, the display

may be unstable or indicate incorrect measurement values.

Feature Usage

•Peak Hold - Utilized with AC Voltage or Current measurements, this function holds the

peak measurement on the display. Push Peak Hold (P-H) before taking measurement. P-H

will appear on the display. Take measurement and the maximum rms value will appear on

the display. Push Peak Hold button again to turn off this feature.

•Data Hold - Push this button (D-H) when taking a measurement and the measurement

value shown at time button is pushed will be held on the display.

Voltage Measurement

IMPORTANT: Please refer to Safety Information about exceeding voltage maximums.

1. Connect the black test lead to the COM terminal and the red test lead to the VΩterminal.

2. Set the rotary selector switch to the AC Vor DC Vposition for the range you are

testing.

NOTE: If measuring an unknown voltage, start at the highest range then adjust to the proper

lower range for best resolution.

3. Connect the test leads across the source or load being measured. The polarity of the red

lead connection will be indicated at the same time the voltage is displayed.

Current Measurement

1. Connect the black test lead to the COM terminal and the red test lead to the mA terminal for

a maximum of 200mA. For a maximum of 10A, connect the red test lead to the 10A

terminal.

2. Set the rotary switch to the desired AC (A) or DC (A) range.

NOTE: If measuring an unknown current, start at the highest range then adjust to the proper

lower range for best resolution.

3. Turn off power to item being tested. Connect the test leads in series with the load being

measured.

4. Turn on power to item being measured and read value on display. Turn off power again

before disconnecting leads.

Diode Check

IMPORTANT: Before taking any in circuit measurement remove power from the circuit and

discharge all capacitors in the circuit.

1. Set the rotary switch to position and A will be shown on the display.

93-70 Digital Multi-Tester

2. Connect the black test lead to the COM terminal and the red test lead to the VΩterminal.

NOTE: The polarity of the red test lead is +.

3. Connect test leads across the diode to check.

4. The forward voltage drop on LCD should be approximately 0.3~0.9 V. If the LCD reads OL

(over range), reverse the lead connection.

Continuity Test

IMPORTANT: Before conducting this test be sure there is no voltage present in the circuit.

Please refer to Safety Information before proceeding.

1. Connect the black test lead to the COM terminal and the red test lead to the VΩterminal.

2. Set the rotary selector switch to the 200 position.

3.` Connect the test leads across the two points being measured. The value of the resistance

will appear on the display.

4. If the resistance is less than approximately 30Ω, the unit will produce a continuous tone in

addition to displaying the value.

Resistance Measurement

IMPORTANT: Before conducting this test the device being tested should be turned off, any

capacitors should be discharged and voltage should not be present. Please

refer to Safety Information before proceeding.

1. Connect the black test lead to the COM terminal and the red test lead to the VΩterminal.

NOTE: The polarity of the red test lead is +.

2. Set the rotary selector switch to the Ωposition for the range you are testing.

NOTE: If measuring an unknown resistance, start at the highest range then adjust to the

proper lower range for best resolution.

3. Connect the test leads across the resistance being measured. The resistance value will

appear on the display.

Frequency Measurement

1. Connect the black test lead to the COM terminal and the red test lead to the VΩterminal.

2. Set the rotary switch to the Hz position.

3. Connect the test leads across the source or load under measurement. The frequency value

will appear on the display.

Phase Sequence Indication

IMPORTANT: When connecting leads to a 3 phase system, turn off power, connect leads and

then restore power to take reading.

1. Set the rotary switch to the RST position.

2. Connect the red test lead to the Rterminal, the yellow test lead to the Sterminal and the

black test lead to the Tterminal. The buzzer will sound and will appear on the display.

3. Check that power is not present in system. Then connect the test leads to the 3-phase AC

circuit. Restore power to take reading.

4. One of the following results should appear on the display:

a. A right arrow symbol - the circuit is positive phase sequence.

b. A left arrow symbol - the circuit is negative phase sequence.

c. No arrow - the three phase circuit is only sending two phase voltage.

Temperature Measurement

1. Set the rotary selector switch to the °For °Cposition.

2. Connect probe plug to Temperature Input Connector.

NOTE: Uses standard Type K thermocouple (NiCr/Ni) probes; see below for Greenlee probe

information.

3. Place probe tip in contact with item being measured. The temperature will appear on the

display.

Greenlee Temperature Probes (Type K, NiCr/Ni)

For use with 93-70 digital MultiTester and 93-1062 Digital Thermometer, plus other devices

using Type K probes.

5794-75TIP/34942 - Replacement Tip for 5794-75 Liquid Probe.

Cat./UPC No. 5791/34558 5792/34559 5793/34560 5794/34561

5794-75/34562

5795/34563

Probe Tip

Application Pipe Air/Gas Semi-Solid Liquid Liquid Surfaces

Range °F-58 - +572 -58 - +1112 -58 - +1112 -58 - +2012 -58 - +2012 -58 - +842

(°C) (-50 - +300) (-50 - +600) (-50 - +600) (-50 - +1100) (-50 - +1100) (-50 - +450)

To Measure Heat System Exhaust, Meats, Water, Water, Stove Plates,

Temp. of Components Fumes, etc. Foods, etc. Oil, etc. Oil, etc.

Heat Units, etc.

Response 5 sec. 5 sec. 12 sec. 12 sec. 12 sec. 6 sec.

Length or Max. Pipe Dia. 5" 5" 5" 29-1/2" 5"

Capacity

1-3/8" (35 mm)

(130 mm) (130 mm) (130 mm) (750 mm) (130 mm)

93-70 Digital Multi-Tester

SPECIFICATIONS

Display: Liquid Crystal Display (LCD) 3-1/2 digit plus icons. Maximum

reading of 1999.

Polarity Indication: Automatic, displays “–” for negative.

Sampling: 2.5 times per second

Overload Protection: 10A/600V 0.3Ø x 38 mm, 0.5A/250V 5Ø x 20 mm

Overrange Indication: OL appears on display

Low Battery: BAT appears on display

Auto Power Off: After approximately 26 minutes

Power Requirements: 1 - 9V battery, shipped installed in unit

Operating Temperature: 32°to 104°F (0°to 40°C)

Storage Temperature: 14°to 140°F (-10°to +60°C)

Relative Humidity: 0% to 80% operating; 0% to 70% storage

Dimensions: Approx. 7-3/8" x 3-3/8" x 1-1/2" (186 x 86 x 39 mm),

without protective holster

Weight: Approximately .88 lb. (400 g)

DC Voltage

Range Resolution Accuracy Over-voltage Protection

200mV 100µV±(0.5% + 1 digit)

2V 1mV 1000V DC

20V 10mV ±(0.5% + 3 digits) 750V rms AC

200V 100mV

1000V 1V

Input Impedence: 10MΩ

AC Voltage (40 Hz ~ 500 Hz)

200mV 100µV±(0.5% rdg. + 5 digits)

2V 1mV 1000V DC

20V 10mV ±(1.2% rdg. + 5 digits) 750V rms AC

200V 100mV

750V 1V ±(1.5% rdg. + 5 digits)

Input Impedence: 10MΩ

93-70 Digital Multi-Tester

DC Current

Range Resolution Accuracy Voltage Burden

200µA 100nA

2mA 1µA±(1.2% rdg. + 2 digits) <0.7V

20mA 10µA

200mA 100µA

10A 10mA ±(2.5% rdg. + 3 digits) <0.3V

Overload Protection: 0.5A/250V Fuse, less than 200mA; 10A/600V Fuse for 10A Range

AC Current (40 Hz ~ 500 Hz)

200µA 100nA

20mA 10µA±(1.5% rdg. + 3 digits) <0.7V

200mA 100µA

10A 10mA ±(3% rdg. + 1 digit) <0.3V

Overload Protection:

0.5A/250V Fuse, less than 200mA; 10A/600V Fuse for 10A Range

Diode Check

Range Resolution Test Voltage Test Current Overload Protection

1mV 3.3V max. 0.7mA AC/DC 500V rms

Continuity

Range Resolution Sound Open Voltage Overload Protection

0.1Ω<30Ω3.3V max. AC/DC 250V rms

Resistance

Range Resolution Accuracy Overload Protection

200Ω0.1Ω±(1.2% rdg. + 4 digits)

2KΩ1Ω

20KΩ10Ω±(1% rdg. + 2 digits) AC/DC

200KΩ100Ω500V rms

2MΩ1KΩ

20MΩ10KΩ±(3% rdg. + 5 digits)

Open Circuit Voltage: >0.3V, except 200Ωwhich is max. 3.3V

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Equipo de prueba de Greenlee

Greenlee

Greenlee 45081 Manual de usuario

Greenlee

Greenlee 6706 Manual de usuario

Greenlee

Greenlee RT-10 Manual de usuario

Greenlee

Greenlee 6700 Manual de usuario

Greenlee

Greenlee CMGRT-100 Manual de usuario

Greenlee

Greenlee 5774 Manual de usuario

Greenlee

Greenlee IPM-100 Manual de usuario

Greenlee

Greenlee Compact DSP Manual de usuario

Greenlee

Greenlee GT-540 Manual de usuario

Greenlee

Greenlee NETcat NC-100 Manual de usuario

Greenlee

Greenlee 5715 Manual de usuario

Greenlee

Greenlee DVC-6 Manual de usuario

Greenlee

Greenlee TC1S Manual de usuario

Greenlee

Greenlee 5715 Manual de usuario

Greenlee

Greenlee 6711 Guía

Greenlee

Greenlee 5123 Manual de usuario

Greenlee

Greenlee CMGRT-100A Manual de usuario

Greenlee

Greenlee 6706 Manual de usuario

Greenlee

Greenlee 200XP Manual de usuario

Greenlee

Greenlee PA1574 Manual de usuario

Greenlee

Greenlee 200fp Manual de usuario

Greenlee

Greenlee 6701 Manual de usuario

Greenlee

Greenlee 6710 Manual de usuario

Greenlee

Greenlee CS-2072 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario