Gree GTHD(09)AANK3A1AI Manual de usuario
OPERATION
INSTALLATION
&
INSTRUCTIONS
FLOOR AND CEILING TYPE UNIT
GREE ELECTRIC APPLIANCES, INC. OF ZHUHAI
Read this operating & installation instruction carefully and keep it for future reference
MODEL
GTHD(09)AANK3A1AI
GTHD(12)AANK3A1AI
GTHD(18)AANK3A1AI
HEATPUMPSYSTEM
CONTENTS
OPERATION INSTRUCTIONS
1. Part names and their functions........................................................................................................... 1
2. How to use the remote control to operate the unit.............................................................................. 2
3. Maintenance............................................................................................................................................11
4. Operating guide................................................................................................................................. 12
5. Precautions ....................................................................................................................................... 13
6. Checking before contact the service man......................................................................................... 14
INSTALLATIONINSTRUCTIONS
7. Installation of Indoor unit.................................................................................................................... 15
8. Refrigerant piping work ..................................................................................................................... 18
9. DRAIN PIPING WORK ...................................................................................................................... 19
10. Test running ...................................................................................................................................... 20
11. ROUTINE CHECK AFTER INSTALLATION..................................................................................... 21
12.FAULT INDICATION.........................................................................................................................22
1
1
Remote Control
Remote Control Holder
PARTNAMESANDTHEIRFUNCTIONS
OPERATION INSTRUCTIONS
2
Name and Function-Remote control
Note:
Be sure that there are no obstructions between receiver and remote controller.
Don’t drop or throw the remote controller.
Don’t let any liquid in the remote controller and put the remote controller
directly under the sunlight or any place where is very hot.
SWING button
When it is pressed, the louvers
start to rotate automatically and
stop when repressed.
FAN button
Press this button to change
the fan speed of:
“ ” COOL mode
“ ” DRY mode
“ ” FAN mode
“ ” HEAT mode
ON/OFF button
Press this button to turn
on or turn off the unit.
MODE button
press this button to change the
operation mode in order of:
AUTO
TEMP. button
SET TEMP. increases 1 by
pressing button once,and de-
creases 1 by pressing button
once.
At COOL mode operation, SET
TEMP. can be selected from 16
to 30 .
At DRY mode operation, SET
TEMP. can be selected from 16
to 30 .
At HEAT mode operation, SET
TEMP. can be selected from 16
to 30 .
2
Howtouse the remote control tooperate theunit
OPERATION INSTRUCTIONS
3
Name and Function-Remote control. (Remove the cover)
Note: This type of remote controller is a kind of new current controller.
some buttons of the controller which are not available to this Air con-
ditioner will not be described below.
Operate on unmentioned buttons would not impact on the normal use.
SLEEP button
PressthisbuttontosetSLEEP
operation, and stop when re-
pressed
Liquid crystal displayer. It
shows all set contents.
TIMER ON button
At stopping, press TIMER ON button,
set ON TIME in range of 0 to 24 hour
at the interval of 0.5h to start the unit
automatically.
TIMER OFF button
At operating, press TIMER
OFF button, set OFF TIME
in range of 0 to 24 hour to
stop the unit automatically.
0 24h
Timer
cancellation
0 24h
Timer
cancellation
How to use theremote control to operate the unit
OPERATION INSTRUCTIONS
4
COOL mode operation procedure
4.Press FAN button, set
fan speed.
5.Press TEMP. but-
ton, set suitable SET
TEMP.
2.Press MODE button,
set operation
mode.
3.Press SWING button,
the louvers start to ro-
tate automatically, and
stop when repress.
1.Plug in, press ON/OFF button,then air
conditioner is turned on.
According to difference between room temp. and set temp., microcomputer can control
cooling on or not.
If room temp. is higher than set temp., compressor runs at COOL mode.
If room temp. is lower than set temp., compressor stops and only indoor fan motor runs.
SET TEMP. should be in range of 16 to 30
How to use theremote control to operate the unit
OPERATION INSTRUCTIONS
5
HEAT mode operation procedure
If roomtemp.is lower than set temp, compressor runs at HEAT mode;
If roomtemp. is higher than set temp., compressor and outdoor fan motor stop.
SET TEMP. should be in range of 16 to 30
3.Press SWING button, the
louvers start to rotate
automatically, and stop
when repress it.
4.Press FAN button, set
fan speed.
5.Press TEMP. button, set
suitable SET TEMP.
1.Plug in, press ON/OFF
button,then air condi-
tioner is turned on.
2.Press MODE button,
set operation mode.
The unit (cool only) do not receive the
control signal which is used under the
heat mode.
How to use theremote control to operate the unit
OPERATION INSTRUCTIONS
6
DRY mode operation procedure
If roomtemp. is lower than set temp., compressor ,outdoor fan motor stop. If room temp. is
between 2of set temp., airconditioneris drying.If roomtemp. is higher than set
temp, it’s at COOL mode.
SET TEMP. should be in range of 16 to 30
3.Press SWING button,
the louvers start to ro-
tate automatically, and
stop when repress it.
4.Press TEMP. button,set
suitable SET TEMP.
2.Press MODE button,set
operation mode.
Air speed couldn’t be
changed after the
being set.
1.Plug in,pressON/OFF button,then
air conditioner is turned on.
How to use theremote control to operate the unit
OPERATION INSTRUCTIONS
7
AUTO mode operation procedure
Under Auto mode operation, standard SET TEMP. is 25 for COOL mode and 20 for
HEAT mode.
1
.Plug in,press ON/OFF button, then
air conditioner is turned on.
2.According to room temp. micro-
computer can automatically set
operation mode,so
as for best effect.
How to use theremote control to operate the unit
OPERATION INSTRUCTIONS
8
TIMER mode operation procedure
At stopping,press TIMERON
button, set ON TIME in
range of 0 to 24 hour to start
the unit automatically.
At operating,press TIMER
OFF button, set OFF TIME
in range of 0 to 24 hour to stop
the unit automatically.
024h
Timer
cancellation
0 24h
Timer
cancellation
How to use theremote control to operate the unit
OPERATION INSTRUCTIONS
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Acondicionador de aire de Gree
Gree
Gree WHD(18)ND3CO Manual de usuario
Gree
Gree ETAC2-07HC230VA-A Manual de usuario
Gree
Gree GWH07AAAXA-K3NNA5A Manual de usuario
Gree
Gree GMV-ND100L/A-T Manual de usuario
Gree
Gree GWH(09)RA-K3DNA1E/I Manual de usuario
Gree
Gree GWHD(24)NK3FO Manual de usuario
Gree
Gree GJC05BT-A6NRNE1A Manual de usuario
Gree
Gree E-TAC Manual de usuario
Gree
Gree SOLEUSAIR SG-WAC-06SE Manual de usuario
Gree
Gree GWC12NC-K3NNA3F Manual de usuario
Gree
Gree GMV-Y96WM/A-F(U) Manual de usuario
Gree
Gree GWH09UB-K3DNXXB Manual de usuario
Gree
Gree GJC10BL-A6NRNC5D Manual de usuario
Gree
Gree GWH18MC-K3DNA2G Manual de usuario
Gree
Gree TS15-8PACWHTK1-A Manual de usuario
Gree
Gree GWHD14NK3BO Manual de usuario
Gree
Gree HLR8Pd/Na-K Manual de usuario
Gree
Gree TOSOT MOMA-19 Manual de usuario
Gree
Gree GMV-224WM/G-X Manual de usuario
Gree
Gree FGR25Pd/DNa-X Manual de usuario
